Kenmore Elite 66513759K602 dishwasher Parts

Common Kenmore dishwasher problems include not starting, stopping mid-cycle, not filling with water, not draining, leaking, and poor cleaning. On Kenmore Elite model 66513759K602, many issues trace back to power, door latch, water supply, or a worn pump, valve, seal, or control.

Most common symptoms and what they usually mean

• Won’t start or stops during a cycle: door not fully latched, cycle not set correctly, power interruption, tripped breaker, or a blown house fuse.
• No water in the tub after starting: water shutoff valve is off, supply issue, or a failing inlet valve.
• Water won’t drain: drain hose restriction, clogged drain path, or a weak drain pump.
• Leaks: door seal wear, tub edge debris, or installation issues (hose routing, clamps).
• Poor cleaning: loading issues, spray arm blockage, or maintenance needed.

Quick checks we recommend first (fast and free)

These checks align with the troubleshooting guidance for this model in the documentation.

• Reset the circuit breaker or replace a blown house fuse.
• Confirm the door is closed tightly and latched.
• Verify the cycle is selected correctly, then press Start/Resume.
• Make sure the water supply valve is turned on.
• Start a short cycle; after about 2 minutes, open the door and confirm water is in the bottom of the tub.

Parts that commonly solve these problems

If the basic checks pass, these model-compatible parts are frequent fixes:

Symptom	Common part to check	Example model-compatible part
Not draining	Drain pump, drain hose	Dishwasher drain pump WPW10348269, dishwasher drain hose 8269144A
Not filling	Water inlet valve	Dishwasher water inlet valve WPW10158389
Dead or intermittent power	Fuse, control board	Fuse W10258275, dishwasher electronic control board WPW10084141
Leaking at door	Door seal	Dishwasher door seal W11196317

Why it matters

Dishwasher problems often look “major” but start with simple causes like a tripped breaker, a door that is not fully latched, or the water valve being off. Catching those early prevents repeat cycle failures and helps avoid water damage.

For model-specific operating steps, cycle behavior, and troubleshooting, use the 66513759K602 owner’s manual.

Last updated: January 2026

On Kenmore Elite dishwasher model 66513759K602, the F4E1 service code points to a wash motor or wash pump (circulation) problem, meaning the dishwasher is not moving water through the spray arms correctly. After correcting the cause, clear the code using the reset steps in the 66513759K602 owner's manual.

What you’ll usually notice with F4E1

• Dishes come out dirty because spray pressure is weak
• You hear abnormal humming or grinding during wash
• The cycle may stop early or drain without washing well
• Water may be present but not circulating
• The unit may run but cleaning performance drops sharply

What to check first (before replacing parts)

1. Power reset: Turn off the breaker for 1 minute, then restore power.
2. Loading and spray arms: Make sure tall items are not blocking spray arm rotation.
3. Filters and sump area: Clean the filter area and remove debris that can jam the wash system.
4. Water supply: Confirm the shutoff valve is fully open and the fill is strong.
5. Drain issues that mimic wash issues: If water is not clearing correctly, inspect the drain path and hose routing.

Parts commonly involved when F4E1 won’t clear

If the checks above do not restore normal washing, these model-matched parts are common fixes:

Symptom	Most likely area	Example model-matched part
Hums but little or no spray	Circulation motor / wash pump	Pump motor WPW10780877
Fills but seems to struggle to wash	Water inlet / fill performance	Dishwasher water inlet valve WPW10158389
Drains poorly or leaves water behind	Drain system	Dishwasher drain pump WPW10348269 or dishwasher drain hose 8269144A

Clearing the code after the repair

Many Kenmore Elite dishwashers require a control reset after the underlying problem is fixed. Use the exact key sequence and timing shown in the 66513759K602 owner's manual so the control exits service mode and runs normally.

Why it matters

F4E1 is a wash-performance fault; continuing to run cycles with poor circulation can leave detergent undissolved, reduce sanitizing performance, and increase residue buildup in the sump and spray system.

Last updated: January 2026

The model number for your Kenmore Elite dishwasher is printed on the model and serial number label inside the tub. Open the door and look along the tub frame edge; the label lists both the model number and serial number (see the owner's manual).

Where to look on model 66513759K602

On this Kenmore Elite dishwasher, the label is located inside the door opening on the tub, not on the outer door panel.

• Open the dishwasher door fully.
• Look around the tub frame near the door opening.
• Find the sticker that says “Model” and “Serial.”
• Write down the full model number and serial number exactly as shown.
• Keep the information with your purchase date for future service or parts lookup.

What the label typically includes

Item on label	What it’s used for
Model number	Matching the correct diagrams and replacement parts
Serial number	Identifying the production series for service and compatibility
Purchase date (you record it)	Warranty and service records

Why it matters

Using the exact model number helps us match the correct Kenmore dishwasher parts for your unit, such as a dishwasher drain pump WPW10348269 or dishwasher water inlet valve WPW10158389, and avoids ordering a similar-looking part that will not fit.

Last updated: March 2026