Kenmore 11080754001 stacked laundry center Parts

You can tell the age of your Kenmore stacked laundry center model 11080754001 by reading the model and serial number plate on the unit, then decoding the serial number to find the manufacturing date. The plate location and labeling are shown in the 11080754001 owner's manual.

Where to find the serial number on model 11080754001

On this Kenmore laundry center, the manual shows a model and serial number plate on the appliance cabinet. Common places to check include:

• Inside the washer lid area (around the lid opening)
• On the cabinet frame behind the washer lid
• On the back panel of the laundry center
• Near the dryer door opening on the cabinet frame

How to decode the date from the serial number

Kenmore laundry products were built by different manufacturers over the years, so the serial number format varies. Use this process:

• Write down the full serial number exactly as shown
• Identify the manufacturer format (often tied to the first characters)
• Match the serial format to a Kenmore age chart
• Convert the coded year and month (or week) into a calendar date

Quick decoding guide (what you are looking for)

What the serial code contains	What it tells you	What to do next
Year + month code	Approximate build month/year	Convert to a calendar month/year
Year + week code	Approximate build week/year	Convert week number to a date range
Plant + sequence + date code	Build location plus date info	Focus on the date segment

Why it matters

Knowing the manufacture date helps us choose the right repair approach for your Kenmore 11080754001, including matching the correct washer parts (like a timer, drain pump, or motor coupling) and estimating remaining service life.

Tip for parts and service records

If you are already ordering parts or troubleshooting, keep a photo of the model and serial plate with your records. It speeds up matching parts to your exact laundry center configuration.

Last updated: February 2026

The Kenmore stacked laundry center washer in model 11080754001 is a standard, agitator-style top-load design; these typically measure about 3.2 to 3.5 cu. ft. Use the model-specific spec listing in the 11080754001 owner's manual to match the exact capacity for your unit.

How to get the exact capacity for model 11080754001

Use the manual first because it ties the capacity to the exact Kenmore model and configuration.

• Open the Specifications section (sometimes listed as “Dimensions” or “Capacity”)
• Confirm the model and serial number plate matches 11080754001
• If capacity is listed in liters or gallons, convert to cubic feet (see table below)
• If only basket dimensions are listed, use those to compare to typical top-load sizes
• Match the control panel features (Heavy Duty, Permanent Press, Knit/Delicate, Soak) to ensure you are using the correct manual

Quick conversions (if the manual lists volume in another unit)

If you see this in the manual	Equals
1 cubic foot	7.48 gallons
1 cubic foot	28.3 liters
25 gallons	3.34 cu. ft.

Why it matters

Washer capacity affects load size, cleaning action around the agitator, and spin balance. Staying within the rated capacity helps prevent poor wash performance, out-of-balance spinning, and excess wear on drive components.

Last updated: February 2026

For the Kenmore 11080754001 stacked laundry center, the most common problems are washer no-spin or no-agitate, washer not draining, excessive vibration, and dryer no-heat or no-start. These symptoms usually trace to a small set of wear parts and a few basic checks in the owner's manual.

Most common symptoms and likely causes

• Washer won’t spin or agitate: worn drive coupling, lid switch not closing, clutch wear
• Washer won’t drain: clogged or failing drain pump, kinked drain hose
• Washer is noisy or bangs: tub support wear, counterweight spring issues, unbalanced loads
• Dryer won’t start: push-to-start switch failure, door not latching
• Dryer runs but won’t heat: heating circuit wiring issue (and related heater components)

Parts that commonly fix these issues

If your symptoms match, these model-compatible parts are frequent solutions:

• Coupling 285753A (washer won’t agitate/spin)
• Washer lid switch assembly WP3355806 (washer won’t spin, intermittent operation)
• Washer drain pump WP3363394 (won’t drain, humming, slow drain)
• Clutch 285785 (weak spin, slow or incomplete spin)
• Dryer push-to-start switch WP3977456 (dryer won’t start)

Quick checks we recommend before replacing parts

1. Confirm the lid and dryer door fully close; listen for a solid click.
2. Run a drain and spin; if you hear a hum but no drain flow, suspect the pump or a blockage.
3. Check for kinked hoses and a restricted standpipe (slow drain can mimic a bad pump).
4. Reduce to a small, balanced load to rule out out-of-balance vibration.
5. If the dryer won’t heat, inspect for loose or heat-damaged wiring at the heater circuit.

Symptom-to-part cheat sheet

Symptom	Most common part to check	What you’ll notice
No agitate/no spin	Coupling	Motor runs but tub/agitator doesn’t move normally
No spin (fills, agitates)	Lid switch assembly	Stops when lid is opened, may be intermittent
Won’t drain	Drain pump	Water stays in tub, may hum or drain slowly
Weak spin	Clutch	Clothes wetter than normal after spin
Dryer won’t start	Push-to-start switch	Button feels normal but motor never starts

Why it matters

Catching these issues early prevents secondary damage, like a slipping drive system wearing the gearcase, or a slow drain causing repeated cycle failures. Using model-matched Kenmore parts helps restore proper fit and performance.

Last updated: March 2026