Installation guide
Owner’s manual
Error Codes
How to reset Kenmore oven model 79096122409?
To reset the Kenmore electric range model 79096122409, turn the oven controls off, then reset power by switching the range circuit breaker off and back on. After power is restored, reset the clock and reselect your oven function as needed (bake, broil, timer).
- Turn all surface element knobs to OFF.
- Set the oven to OFF/Cancel.
- Switch the range breaker OFF for about 1 minute.
- Switch the breaker ON.
- Reset the clock and then test Bake or Broil.
For control-specific steps and safety notes, follow the 79096122409 owner's manual.
This model has an oven lockout feature that can make the keypad seem unresponsive. If you see “LOC” or the door lock indicator is on, cancel lockout:
- Press and hold the oven lockout pad for 3 seconds.
- Wait about 15 seconds for the door lock motor to finish.
- Confirm the display returns to the time of day.
Use this checklist to narrow down whether you had a simple control glitch or a part issue:
- Display is blank: check the breaker, power cord, and terminal connections.
- Oven heats poorly or is inaccurate: test with an oven thermometer; the sensor may be the issue.
- Broil works but bake does not (or vice versa): suspect a failed heating element.
- Error code returns immediately: troubleshoot the specific code.
| Symptom after reset | Most likely area | Common next step |
|---|---|---|
| No heat in bake | Bake circuit/element | Inspect and ohm-test the element 316407501 |
| Temperature swings | Sensor/control | Check the frigidaire range oven temperature sensor 316490000 |
| Error code on display | Control/sensor/wiring | Use Kenmore 790 range 4-digit error codes |
A reset clears temporary control faults after a power interruption, but it also helps you confirm whether the problem is a repeating failure (like a bad bake element, temperature sensor, or wiring) that needs repair.
Last updated: January 2026
What does EO F2 mean on Kenmore oven?
On Kenmore range model 79096122409, an E0 F2 (sometimes shown as EO F2) display points to an electronic control problem, most often a keypad (touchpad) input issue or an oven control fault. Start by clearing the code with STOP/CLEAR and resetting power.
- Press STOP/CLEAR to clear the display and stop the beeping.
- Turn the range OFF at the circuit breaker for about 5 minutes, then restore power.
- If the code returns immediately, avoid using Bake/Broil until the issue is corrected.
- If the control panel was recently cleaned, let it dry fully; moisture can trigger false key signals.
- Check that no buttons are stuck or being pressed by a misaligned control overlay.
Many E0 F2 events are caused by a “stuck key” condition or a failing touchpad ribbon connection.
- Inspect the control panel for stuck, damaged, or unresponsive keys.
- If you can access the back of the control, reseat the keypad ribbon cable (unplug power first).
- If the oven temperature seems inaccurate (separate issue), use the calibration steps in the 79096122409 owner's manual.
| What you notice | Most likely cause | What usually fixes it |
|---|---|---|
| Beeping with E0 F2 right after power-up | Keypad signal fault | Keypad/control overlay or touchpad service |
| Code appears after cleaning the panel | Moisture under keypad | Dry time, gentle cleaning habits |
| Random beeps, intermittent code | Loose ribbon connection or failing control | Reseat connection, then replace failed component |
If troubleshooting points to a control input problem, these model-related parts are commonly checked during diagnosis:
- Range control overlay 316419141 (overlay can contribute if it’s peeling or misaligned)
- Range control overlay 316419137 (alternate overlay option depending on finish)
An E0 F2 condition can disable normal oven operation and may cause unexpected beeping or unresponsive controls. Clearing the code and confirming the keypad and control connections helps prevent repeat shutdowns and restores reliable Bake and Broil use.
Last updated: January 2026
What is the width of a Kenmore range?
For the Kenmore electric range model 79096122409, the overall width is 30 inches (the cabinet opening is typically 30 inches wide as well). We use the exact clearance and dimension diagram in the 79096122409 installation guide to size the cutout and confirm fit.
- Overall width: 30 in.
- Overall depth: about 25-3/4 in. (body)
- Depth with door handle: 28-13/32 in.
- Overall height: about 46-1/8 in. to 46-5/8 in. (varies by leveling legs)
| Measurement | What it means | Typical use |
|---|---|---|
| 30 in. width | Side-to-side outside dimension | Cabinet opening and countertop fit |
| 25-3/4 in. depth | Front-to-back range body | Planning clearances behind the unit |
| 28-13/32 in. depth | Depth including handle | Door swing and walkway clearance |
- Measure across the widest point of the range top, left to right.
- Measure with the range pushed back into its normal position.
- Do not include the oven door when it is open.
- If you are checking a cabinet opening, measure inside-to-inside of the cutout.
Using the correct width prevents installation problems like rubbing against cabinets, misaligned anti-tip bracket placement, and insufficient side clearance near combustible surfaces.
For the full clearance diagram and cabinet spacing notes, use the 79096122409 installation guide.
Last updated: January 2026
