Kenmore 10650269990 side-by-side refrigerator Parts

Yes. Several brands make 30-inch class side-by-side refrigerators, but true 30-inch wide side-by-side models are less common than 33-inch and 36-inch sizes. For fit, we recommend confirming the exact cabinet opening and required clearances in your owner's manual before choosing a replacement.

What “30 inch” usually means (and what to measure)

When shoppers say “30 inch,” they may mean the cabinet opening, not the exact refrigerator width. Measure these before you buy:

• Opening width (wall to wall at the front)
• Opening depth (including baseboard and door swing clearance)
• Height (floor to cabinet or soffit)
• Door swing space (especially next to a fixed wall)
• Ventilation gaps (side, top, and rear)

Clearance guidance that affects fit

For Kenmore model 10650269990, the manual calls out common installation clearances that can change what size refrigerator will work in a 30-inch opening:

• Allow about 1/2 inch of space on each side and at the top for ventilation
• If installed next to a fixed wall, allow about 2 inches minimum on the hinge side (varies by setup) so the door can swing open
• If an ice maker is used, leave extra space at the back for the water line connection

Quick comparison: common widths vs. availability

Nominal size shoppers ask for	Typical actual width range	How common in side-by-side style
30 inch	~29 1/2 to 30 1/2 inches	Less common
33 inch	~32 3/4 to 33 1/2 inches	Common
36 inch	~35 1/2 to 36 1/2 inches	Very common

Why it matters

Side-by-side doors need swing room, and the refrigerator needs airflow. In a tight 30-inch opening, even a small clearance requirement can push you toward a narrower cabinet or a different refrigerator style.

Last updated: February 2026

Your Kenmore side-by-side refrigerator model 10650269990 has its exact cubic-foot capacity listed on the model and serial number label inside the fresh food compartment, and it may also be shown in the specifications section of the owner's manual. This is the most accurate way to match capacity to your exact configuration.

Where to find the cubic-foot capacity (fastest checks)

Look in these common places on Kenmore 106 models:

• Model and serial number label on the inside wall of the refrigerator compartment
• Specifications section in the owner's manual
• Product literature pages included with the refrigerator (if you still have them)
• If the label is hard to read, take a photo and zoom in to find “Capacity” or “Total capacity”

What you will typically see on the label

Capacity is usually shown as one of these:

Label wording	What it means
Total capacity	Combined refrigerator + freezer cubic feet
Refrigerator capacity	Fresh food section only
Freezer capacity	Freezer section only

Why we recommend the rating label over “model number lookups”

Kenmore model numbers can cover multiple production variations (features, dispenser style, ice maker setup). The inside label ties the cubic-foot rating to your exact unit, which prevents ordering the wrong bins, shelves, or ice maker parts.

Related parts that depend on the exact model configuration

If you are checking capacity because you are replacing storage parts or ice and water components, confirm the model/serial label first, then match parts to your model:

• Refrigerator crisper pan WP2188656 (drawer size and rail fit can vary)
• Refrigerator glass shelf WPW10141748 (shelf width and support style can vary)
• Ice maker assembly - refrigerator ice maker by whirlpool 4317943 (ice system configuration can vary)

Last updated: February 2026

To replace the ice maker in your Kenmore 10650269990 side-by-side refrigerator, we disconnect power, shut off the water supply, remove the ice bin or bucket, swap the ice maker assembly, then restore power and water and confirm ice production starts normally (typically within 24 hours).

Before you start (safety and prep)

• Unplug the refrigerator (or switch off the breaker); disconnect power before servicing.
• Turn off the household water shut-off valve feeding the refrigerator.
• Empty the ice bin or bucket so you can work without spills.
• Use only a plastic utensil to clear any jammed cubes; never use anything sharp.
• Keep screws and brackets organized so the new unit mounts the same way.

Remove the ice bin or bucket (common Kenmore 106 steps)

Your model may use an interior bin or a door-mounted bucket. The owner's manual shows both styles.

• Interior bin style: lift the wire shut-off arm to OFF (up), lift the front of the bin, and pull it out.
• Door bucket style: press the release button, lift the bucket up and out (the ice maker will not run without the bucket installed).
• If your ice maker has an ON/OFF switch, slide it to OFF before removal.

Replace the ice maker assembly

1. With power off, open the freezer and access the ice maker mounting area.
2. Remove the mounting screws and any cover or service door needed for access.
3. Disconnect the ice maker wiring harness plug.
4. Install the replacement ice maker, reconnect the harness, and secure all screws.
5. Reinstall the bin or bucket fully; the dispenser will not work if the bin is not pushed in all the way.

Recommended replacement part for this model: Ice maker assembly - refrigerator ice maker by whirlpool 4317943

What to expect after installation

Item	Typical expectation
First ice	Up to 24 hours after restart
Normal production	About 7 to 9 batches per 24 hours
Maximum ice mode (if equipped)	About 10 to 14 batches per 24 hours

Why it matters

A correctly installed ice maker (properly seated bin or bucket, switch ON, water valve open) prevents “no ice” complaints that are actually caused by a shut-off arm position, an OFF switch setting, or a bucket not fully installed.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10650269990, the model number is printed on the model and serial number label located on the inside wall of the refrigerator compartment (fresh food section). Use that label any time you’re matching parts or looking up service information in the owner's manual.

Where to look (quick checklist)

• Open the refrigerator (fresh food) door, not the freezer door
• Look along the inside side wall of the refrigerator compartment
• Check near the upper side wall and around the crisper area
• Use a flashlight; the label can be easy to miss
• Wipe condensation or smudges off the label so the numbers are readable

What you’ll find on the label

The same label typically includes both identifiers you need:

Item on label	What it’s used for	Example format
Model number	Matching the correct parts diagrams and parts	10650269990
Serial number	Identifying production details for service records	Letters and numbers

Why it matters

We use the exact model number to show the correct Kenmore parts list for your refrigerator. Even small model-number differences can change which ice maker, water inlet valve, thermostat, or door gasket fits.

Tip for ordering the right part

• Copy the model number exactly as printed
• Take a clear photo of the label for reference
• When replacing water and ice components, match by model first, then confirm the part

Last updated: February 2026