Kenmore 79046579400 electric range Parts

On the Kenmore electric range model 79046579400, the model and serial number are printed on the serial plate on the oven front frame behind the oven door (and on some versions, behind the storage drawer). This label is the fastest way to confirm the exact model for parts and service.

Where to look on model 79046579400

Check these common label locations in this order:

• Open the oven door and look on the front frame around the oven opening (often along the side).
• If you do not see it, pull out the bottom drawer and look behind the drawer along the frame.
• Look for a plate or sticker that lists Model, Serial, and sometimes a lot number/letter.

What the label looks like and what to write down

The serial plate usually includes the details you need to match parts correctly.

Label item	What it’s used for	Example of what you’ll see
Model number	Identifies the exact range design	79046579400
Serial number	Tracks production run	Letters and numbers
Lot number/letter (if shown)	Helps match revisions	Single letter or code

For model-specific diagrams and identification details, use the 79046579400 owner's manual.

Why it matters

Kenmore ranges can look similar across multiple model series, but parts like a bake element, oven temperature sensor, control overlay, or terminal block can vary by model and production run. Using the serial plate information helps us match the correct replacement part the first time.

Last updated: January 2026

To reset a Kenmore electric range model 79046579400, turn the range power OFF at the circuit breaker for 1 minute, then turn it back ON and reset the clock. This clears many control glitches after a power surge or error.

Quick reset steps (control reboot)

• Turn all surface burner knobs to OFF.
• Switch the range OFF at the house breaker (or remove the fuse).
• Wait 60 seconds.
• Restore power.
• Set the clock and test Bake and Broil.

If you need the exact control pad names for your unit, follow the steps in the 79046579400 owner's manual.

If the oven still will not heat after a reset

A reset fixes software-like glitches; it will not fix a failed heating circuit. Check these common causes:

• Bake element not heating (often visible blistering or a break)
• Oven temperature sensor out of range or wiring issue
• Control not sending voltage to the element
• Terminal block or power cord connection problem (burnt connection can cause partial power)

Common symptoms and what they usually point to

Symptom	Most likely area to check	What to do next
Display works but oven stays cold	Bake circuit	Inspect element and wiring; test for heat in Bake
Oven heats but temperature is inaccurate	Sensor or calibration	Check sensor; use calibration feature if needed
Random beeping or error returns after reset	Control or sensor	Look up the code and follow the diagnostic steps

For temperature problems, the model’s calibration procedure is covered in the 79046579400 owner's manual.

Error codes (when a reset is not enough)

If an error code comes back after restoring power, use the code list and troubleshooting steps for Kenmore 790 ranges in Kenmore 790 self-cleaning range error codes.

Why it matters

Resetting power is the fastest safe way to clear a stuck relay state or control logic fault. If the problem returns, focusing on the bake element, sensor, and power connection helps you avoid replacing the wrong part.

Last updated: January 2026

For the Kenmore electric range model 79046579400, the cooktop is 31 1/2 inches wide, and it’s designed to fit a 30-inch cabinet opening. For exact installation clearances and cutout dimensions, use the installation guide.

Model 79046579400 width details

Here’s how “width” is commonly described for this range:

• Cooktop width (top rim/overhang): 31 1/2 in.
• Cabinet opening (between base cabinets): 30 in.
• Rear body width (with body sides): about 28 1/8 in. (rear width reference)
• Countertop cutout guidance: follow the cutout diagram and minimum cutout width notes
• Fit tip: the cooktop overlaps the countertop edges at the sides

Quick reference table

Measurement type	What it means	Typical value for 79046579400
Cooktop width	Visible top surface that can overlap the counter	31 1/2 in.
Cabinet opening	Space between base cabinets for installation	30 in.
Rear body width	Back-of-range body width reference	~28 1/8 in.

Why widths can look different

Ranges often have a wider cooktop than the cabinet opening because the top is designed to overlap the countertop edges. That overlap helps cover the cutout and gives a finished look, but it also means you should size the opening to the installation spec, not the cooktop edge.

Installation tips that prevent fit problems

• Measure the cabinet opening first; confirm it matches the required opening width.
• Keep the range supported by the leveling legs, not by the smoothtop glass.
• Make sure cabinets are plumb and level before sliding the range into place.
• If you have a formed or tiled countertop, you may need to shave/trim the front corners as shown in the guide.
• Allow room for the anti-tip bracket and verify the rear leg is captured.

Last updated: January 2026