KitchenAid KSRA25ILSS01 side-by-side refrigerator Parts

The KitchenAid KSRA25ILSS01 is a full-size side-by-side refrigerator; most models in this KitchenAid platform are about 33 inches wide, 65 to 71 inches tall, and 30 to 35 inches deep (depth varies most with handles and door swing). For the exact dimensions and capacity for your unit, use the installation guide.

Typical size ranges (what “big” usually means)

These are the measurements customers most often need for fit, delivery, and door clearance:

• Width: typically 32 3/4 to 33 inches
• Height: typically 65 to 71 inches (floor to top of hinge cover)
• Depth (cabinet only): typically 28 to 31 inches
• Depth (with doors/handles): typically 30 to 35 inches
• Clearance needed: extra space for door swing and airflow behind the cabinet

How to measure your KSRA25ILSS01 accurately

Measure the refrigerator itself, not the cutout, and record all three depths.

• Measure width at the widest point (often the hinge side)
• Measure height from floor to the highest point (hinge cover)
• Measure depth three ways: cabinet only, with doors, with handles
• Check door swing clearance so bins and the ice door clear nearby walls
• Confirm rear clearance for the water line and airflow

Quick reference: which measurement to use

What you’re doing	Measurement that matters most	Why
Replacing an existing fridge	Width and height	Ensures it fits the opening
Moving through doorways	Depth with handles (and door swing)	Prevents getting stuck
Planning a remodel	Cabinet depth and required clearances	Avoids ventilation and fit issues

Why it matters

Side-by-side refrigerators like the KSRA25ILSS01 can look similar but vary enough in height and depth to affect installation, door alignment, and water line routing. Using the installation specs prevents clearance problems and helps avoid kinks in the water tube.

Last updated: February 2026

To reset your KitchenAid KSRA25ILSS01 side-by-side refrigerator, we reset power to the control by unplugging the unit (or switching off the breaker) for 5 to 10 minutes, then restoring power. This clears many minor control glitches without replacing parts.

Quick reset steps

• Unplug the refrigerator, or turn OFF the circuit breaker.
• Wait 5 to 10 minutes (do not shorten the wait).
• Restore power.
• Allow 24 hours for temperatures to fully stabilize.
• If the dispenser or ice maker was used recently, dispense water for a minute to help clear air.

What this reset does (and does not do)

A power reset is best for temporary issues like a non-responsive display, lights acting oddly, or intermittent dispensing. It will not fix a mechanical or sealed-system problem.

Symptom after reset	Most likely area to check next	Common next step
No water from dispenser	Water supply or inlet valve	Inspect supply line; test/replace refrigerator inlet valve W10408179
Bad taste/odor, slow flow	Water filter or housing	Replace refrigerator water filter EDR5RXD1; check refrigerator water filter housing WP2186443
Frost buildup, warm fridge	Defrost system	Check refrigerator defrost bi-metal WPW10225581 and refrigerator heater WP2323198

Why it matters

A proper reset is the fastest way to rule out a control-board hiccup before you spend time diagnosing parts like the inlet valve, defrost components, or water filter system.

Helpful reference

For model-specific electrical and installation notes (including safe power shutoff guidance), use the installation guide.

Last updated: February 2026

To replace the water filter on your KitchenAid KSRA25ILSS01 side-by-side refrigerator, remove the old filter from the filter compartment, insert the new filter fully, then lock it in place (typically by pushing in and turning clockwise) until it stops. Follow the exact steps shown in the installation guide.

Before you start

• Use the correct replacement filter for your KSRA25ILSS01; a common match is the refrigerator water filter EDR5RXD1.
• Dispense a few cups of water after installation to clear air and carbon fines.
• If your model has a filter door or cap, make sure it closes smoothly and fully.
• Keep a towel handy; a small amount of water can drip during removal.

Step-by-step: replacing the filter

1. Locate the filter compartment (commonly in the grille/base, inside the fresh food section, or in the upper corner).
2. Turn the old filter counterclockwise to unlock (or press the release, depending on the housing style), then pull it out.
3. Remove protective caps from the new filter.
4. Insert the new filter straight in; push firmly.
5. Turn the filter clockwise until it stops and feels locked.
6. Run water through the dispenser for 2 to 5 minutes (or about 2 to 3 gallons) to flush the system.

If the filter will not turn or seat correctly

• Reinsert the filter and keep it straight; cross-threading or a tilted filter prevents locking.
• Check the filter housing for cracks or a damaged receiver; the refrigerator water filter housing WP2186443 is the common fix when the housing will not hold the filter securely.
• Make sure the old O-rings did not stay behind in the housing.

Quick reference

Symptom	Most likely cause	What to do
Filter will not lock	Filter not fully inserted	Push in firmly, then turn clockwise
Water spurts after change	Air in the water line	Flush several minutes at the dispenser
Slow flow	Clogged filter or low supply pressure	Replace filter; verify supply valve is fully open

Why it matters

A properly installed refrigerator water filter protects water taste and flow, and it helps prevent dispenser and ice maker issues caused by restricted water supply.

Last updated: February 2026

The most common KitchenAid refrigerator problems are ice maker and water dispenser issues (slow ice, no ice, weak water flow) and cooling complaints (warm fridge, freezer frosting). On the KitchenAid KSRA25ILSS01, these symptoms often trace back to airflow, defrost, or water-supply components listed for this model.

Most common symptoms we see

• Ice maker not making ice or making hollow cubes
• Water dispenser flow is slow or stops
• Refrigerator section warms up while freezer seems OK
• Frost buildup on the freezer back wall
• Water leaking or puddling (often from a clogged drain or ice buildup)

Quick checks that fix many calls

1. Confirm temperatures: set the refrigerator to about 37°F and the freezer to about 0°F.
2. Check airflow: make sure vents are not blocked by food packages.
3. Inspect for frost: heavy frost on the freezer back panel points to a defrost problem.
4. Check water supply: verify the shutoff valve is fully open and the supply line is not kinked.
5. Replace the water filter on schedule: a restricted filter can reduce dispenser flow and affect ice production.

Parts that commonly relate to these problems (KSRA25ILSS01)

Problem area	What you notice	Common related part on this model
Water flow to dispenser/ice maker	Slow water, no ice fill	Refrigerator water filter EDR5RXD1, refrigerator inlet valve W10408179
Defrost system	Frosted freezer wall, warming fridge	Refrigerator defrost bi-metal WPW10225581, refrigerator heater WP2323198
Air circulation	Warm spots, poor cooling recovery	(Often involves the evaporator fan area; check for ice or obstructions)

Why it matters

Ice and cooling problems usually get worse over time. A clogged filter or weak inlet valve can starve the ice maker of water, and a defrost failure can choke airflow with ice, making the refrigerator run longer and struggle to hold temperature.

Where to confirm model-specific settings and procedures

Use the installation guide for KSRA25ILSS01 to verify water hookup details, leveling, and setup steps that directly affect ice maker fill and door sealing.

Last updated: February 2026