Kenmore 66513093N413 dishwasher Parts

To hard reset your Kenmore dishwasher model 66513093N413, we recommend canceling the current cycle and draining, then restoring normal operation by restarting a fresh cycle. This clears most “stuck” control states without replacing parts; follow the exact button steps in the 66513093N413 user manual.

Hard reset steps (most effective for a frozen cycle)

• Open the door slightly to stop the cycle.
• Press and hold START for 3 seconds to cancel selections and/or drain.
• Close the door within 3 seconds so the drain can begin.
• Wait until the drain finishes (typically about 2 minutes).
• Select a new wash cycle and options.
• Press START/RESUME to begin.

If it will not start after the reset

A “reset” will not help if the controls are locked or the door is not latching.

• Check for Control Lock; when the lock indicator is lit, buttons are disabled.
• To toggle Control Lock, press and hold SANI RINSE for 3 seconds.
• Confirm the door closes firmly and the latch engages.
• If the door feels loose or won’t stay latched, inspect the dishwasher door latch WPW10653840.

Quick reference: what each action does

Action	What it does	When to use it
Cancel/Drain (hold START 3 sec)	Stops the cycle and drains water	Frozen cycle, wrong cycle selected, standing water
Start/Resume	Restarts after opening the door	Door opened mid-cycle or during delay
Control Lock (hold SANI RINSE 3 sec)	Disables/enables buttons	Buttons unresponsive, lock light on

Why it matters

A proper cancel and drain reset protects wash performance because it clears the current program state and lets the dishwasher refill and heat normally on the next cycle. It also helps you avoid repeated partial cycles that can leave detergent residue and dirty dishes.

Last updated: January 2026

On Kenmore dishwasher model 66513093N413, the model number is printed on the rating label located just inside the door opening, typically along the left side of the tub frame. Open the door fully and read the label for both the model and serial number.

Where to look (fast checklist)

• Open the dishwasher door and look around the inner door frame
• Check the tub opening edge, especially the left side
• Look for a rectangular rating label with small printed text
• Record both the model number and serial number
• Take a clear photo of the label for parts ordering and service

What the label helps you do

Finding the exact model number ensures we match the correct Kenmore parts and diagrams for your dishwasher, including common repair items like the heating element, drain pump, and door latch.

What you need	Where it’s used	Why it matters
Model number (example: 66513093N413)	Parts lookup and fit verification	Prevents ordering the wrong part
Serial number	Date/series identification	Helps confirm production details
Product type (dishwasher)	Manuals and troubleshooting	Ensures correct procedures

Why it matters

Kenmore model numbers can look very similar across 665-series dishwashers, but small differences can change the correct part fit (for example, racks, controls, or pump components). Using the rating label avoids returns and repeat repairs.

Helpful references

• Use the 66513093N413 owner’s manual to confirm where Kenmore lists the model/serial label location and to identify parts and features.
• Use the 66513093N413 installation guide if you need cabinet-opening or mounting details while accessing the unit.

Last updated: January 2026

Common problems on Kenmore dishwasher model 66513093N413 include not starting or stopping mid-cycle, poor cleaning from spray issues, draining problems, and spotting or cloudy dishes. Many of these are caused by loading interference, water temperature, filters, or a worn pump or valve; see the 66513093N413 owner's manual for model-specific troubleshooting steps.

Most common symptoms and what usually causes them

• Dishwasher will not run or lights blink: door not fully latched, Control/Lock enabled, or Start/Resume sequence not completed.
• Detergent left in the dispenser: cycle interruption, blocked spray, or poor water fill.
• Cloudy or spotted dishes: hard water, low rinse aid use, or incoming water below 120°F (49°C).
• Poor cleaning: clogged filter, blocked spray arm holes, or diverter/circulation issues.
• Not draining: kinked/blocked drain hose, clogged air gap, or a failing drain pump.
• Burning smell: food debris on the heater area, plastic contacting the heating element, or a motor/pump problem.

Quick checks we recommend first (fast, no parts)

• Confirm the door closes and latches without dishes hitting the back wash system.
• If Start/Resume is blinking, press START/RESUME and close the door within 3 seconds.
• Verify Control/Lock is off.
• Run hot water at the sink first; target 120°F (49°C) at the dishwasher.
• Clean the filter area and check the lower spray arm for clogs.
• Inspect the drain path (air gap, disposer inlet plug, and hose routing).

Parts that commonly fix these issues on 66513093N413

Symptom	Part to consider	What it affects
Not draining	Dishwasher drain pump W10876537	Pumps water out during drain
Not filling or weak fill	Dishwasher water inlet valve W11175771	Controls water entering the tub
Poor drying or heating	Element assembly W10518394	Heats water and supports drying
Poor wash coverage	Dishwasher spray arm, lower W10849471	Delivers wash water to dishes

Why it matters

Most “dishwasher problems” are really wash-system basics: correct water temperature, proper loading, and clean filtration. Fixing those first prevents repeat clogs, protects the pump and heater, and improves drying and spot-free results.

Last updated: January 2026

For Kenmore dishwasher model 66513093N413, the key “size” spec for fit is the cabinet opening height: it’s designed for a standard opening around 34 1/2 in (87.6 cm), and it can be adjusted to fit openings down to about 33 1/2 in (85.1 cm) with leveling-leg changes. See the 66513093N413 installation guide for the full cabinet opening dimensions.

What to measure before you buy parts or reinstall

Measure these three items so the dishwasher fits and levels correctly:

• Cabinet opening height (underside of countertop to floor)
• Opening width (between cabinet sides)
• Opening depth (front of cabinet to back wall, plus room for hoses and wiring)

If your opening height is tight, the leveling legs matter most for this model.

Height adjustment ranges (what the install guide shows)

The installation instructions include a height adjustment chart that shows how the front and rear leveling legs set the final height.

Cabinet opening height target	What you adjust	What to expect
About 34 1/2 in (87.6 cm)	Factory preset leveling legs	Easiest slide-in fit
About 34 in (86.4 cm)	Lower leveling legs	Common in older cabinets
Down to about 33 1/2 in (85.1 cm)	Remove rear leveling legs/spacers (per guide)	Tighter fit; harder to move into place

Why it matters

Correct sizing prevents the dishwasher from shifting when you open the door, helps the door seal evenly, and keeps the drain hose and wiring routed in the proper “utility connection” area so you avoid leaks, kinks, and vibration noise.

Pro tips for a clean fit and stable operation

• Level the dishwasher front-to-back and side-to-side before securing it.
• Secure the unit to the countertop or side cabinets as directed so it does not tip forward.
• Confirm the door clears mounting screws and brackets after leveling.
• Keep the drain hose routed high (high loop or air gap setup as required) to reduce backflow.
• If the dishwasher will be unused in freezing conditions, winterize it to protect the fill system.

Last updated: January 2026