Kenmore Elite 79574024410 refrigerator Parts

For Kenmore Elite refrigerator model 79574024410, the correct replacement water filter is the Refrigerator water filter 9690 (part number ADQ36006102). You can confirm the filter location and replacement basics in the 79574024410 owner's manual.

How to confirm you have the right filter

We match filters by the full model number and the filter style used in that design. For this model, the compatible filter is already identified.

• Verify the model number on the model and serial label inside the fresh food compartment
• Match the filter by part number (ADQ36006102) rather than the “9690” label alone
• Replace the filter if water flow slows, ice cubes get smaller, or water tastes or smells off
• After installing a new filter, flush the system to clear air and loose carbon

After you replace the filter: flush it correctly

Your manual recommends flushing 2.5 gallons after a filter change to remove trapped air and contaminants.

• Dispense in cycles: 30 seconds ON, 60 seconds OFF
• Keep going until you reach about 2.5 gallons total
• If the dispenser is locked, press and hold Lock for 3 seconds to unlock

Step	What to do	Why it helps
Install	Seat the filter fully and lock it in place	Prevents leaks and low flow
Flush	2.5 gallons in timed cycles	Clears air and carbon fines
Check	Inspect for drips for 1 to 2 minutes	Catches a loose filter early

Parts that apply to this question

• Use the model-matched filter: genuine Kenmore refrigerator water filter 9690 AGF80300801

Why it matters

Using the correct filter for model 79574024410 protects the water valve and dispenser from restriction, keeps ice production steady, and helps maintain water taste and clarity.

Last updated: January 2026

Water leaking from the back of your Kenmore Elite refrigerator model 79574024410 is usually caused by a clogged or frozen defrost drain, a shifted or cracked drain pan, or a water line connection that is seeping after the refrigerator was moved. We focus first on the drain system and the water supply connections.

Quick checks that fix most leaks

• Unplug the refrigerator before inspecting behind panels or near wiring.
• Look for a sheet of ice or standing water under the rear interior panel; that points to a frozen defrost drain.
• Inspect the drain pan underneath for cracks, overflow, or a pan that is not centered.
• Check the 1/4-inch water line and fittings at the rear water valve for slow drips.
• Confirm the cabinet is level so defrost water flows to the drain pan instead of spilling.

Most common causes (and what to do)

Likely cause	What you typically see	What to do next
Defrost drain clogged or frozen	Water under crisper area, then leaks to the back/bottom	Flush the drain with warm water; clear debris with a flexible cleaner
Drain pan out of place or cracked	Water only appears underneath/back	Re-seat the pan; replace if cracked
Water line connection seeping	Drips at the rear valve or tubing	Tighten compression nut slightly; re-check for leaks
Refrigerator not level	Water tracks to one side/back	Adjust leveling legs until stable

Water line connection tips (rear leak source)

The manual’s water line section calls out checking for leaks at the water line connections and routing the tubing so it does not vibrate against the back of the refrigerator or wall. Use these best practices:

• Inspect for moisture at the compression nut and ferrule (sleeve).
• Tighten fittings in small increments; overtightening can deform the ferrule.
• Reposition the tubing coil so it cannot rub or vibrate.

For model-specific diagrams and the exact connection points, use the 79574024410 owner’s manual.

Why it matters

A rear leak can lead to floor damage and can also create ice buildup that restricts airflow, which can cause warm temperatures in the fresh food section or freezer.

Last updated: January 2026

On Kenmore Elite refrigerator model 79574024410, the ER IF error code points to an ice fan problem in the freezer area. That fan pushes cold air through ducts to keep the ice maker and ice room cold; when airflow drops, the control detects it and triggers ER IF. See the troubleshooting section in the 79574024410 owner's manual.

What to check first (fast, no parts)

• Power reset: unplug the refrigerator (or turn off the breaker) for 5 minutes, then restore power.
• Make sure the freezer door closes fully and the door gasket seals all the way around.
• Check for frost or ice buildup around the rear freezer panel (restricted airflow can trigger ER IF).
• Confirm freezer temperature is set correctly (most units run best near 0°F).
• Listen for the ice fan: a working fan usually makes a steady, low whir when the freezer is running.

Common causes and what they mean

What you notice	Likely cause	What to do next
Loud grinding or squealing from freezer	Ice fan hitting ice or failing motor	Defrost any ice buildup; if noise returns, plan a fan repair
Frost blanket on rear freezer panel	Defrost system issue (airflow blocked)	Check for heavy frost; inspect defrost components
Ice maker warm, ice production slow	Poor airflow to ice room	Clear vents, reduce overpacking, check fan operation
Error returns quickly after reset	Fan circuit or control issue	Move to electrical diagnosis or service

Parts that are often involved

If troubleshooting points to the ice maker area (warm ice room, no airflow, repeated ER IF), these model-matched parts are commonly checked during repair:

• Lg refrigerator ice maker AEQ73130004 (ice production issues that can be mistaken for airflow problems)
• Refrigerator defrost sensor assembly 6615JB2005R (helps the unit manage defrost and prevent heavy frost)

Why it matters

The ice fan is what keeps the ice maker compartment cold. When airflow is blocked by frost or the fan is weak, the ice maker warms up, ice production drops, and the refrigerator can struggle to maintain stable freezer temperatures.

Last updated: January 2026