Kenmore 10656584500 refrigerator Parts

On Kenmore model 10656584500, the dispenser drip tray is a small removable tray designed to catch minor spills; it lifts out of the bottom of the dispenser area and can be carried to the sink for emptying and cleaning. For diagrams and dispenser details, use the owner's manual.

Quick steps to remove and reinstall the drip tray

• Remove any cup or ice that is sitting on the tray.
• Grip the tray at the front edge.
• Lift the tray straight up to release it from the dispenser base.
• Pull it out and carry it to the sink (the tray has no drain).
• Rinse and dry the tray, then slide it back into position.
• Push until it sits flat and feels fully seated.

Cleaning tips (safe for plastics)

We recommend mild cleaning to avoid scratching the dispenser area.

• Use warm water and mild dish detergent.
• Use a soft cloth or sponge (not abrasive pads).
• Dry the tray before reinstalling to reduce water spots.
• Wipe the dispenser recess where the tray sits.

If the tray will not come out or will not sit flat

These checks solve most “stuck tray” and “won’t lock in” complaints:

Symptom	Most likely cause	What to do
Tray feels stuck	Dried spills or sticky residue	Wiggle gently while lifting; clean the edges and recess
Tray rocks or sits crooked	Tray not aligned in the recess	Reinsert squarely, then press down evenly
Water keeps pooling	Normal small spills, or frequent dispensing	Empty and clean more often; check for drips after dispensing
Drips after filter change	Air in water lines	Flush water for several minutes; normal use clears air within 24 to 72 hours

Why it matters

Keeping the drip tray clean helps prevent odors, sticky buildup, and dispenser-area mess. It also makes it easier to spot abnormal dripping that could point to a water filter seating issue or a dispenser drip caused by air in the lines.

If you need a replacement water filter for this model, the genuine Kenmore refrigerator water filter EDR3RXD1 is a common match for dispenser performance issues caused by a restricted filter. You can order parts from the list for model 10656584500 or search by model on Sears PartsDirect.

Last updated: February 2026

On Kenmore refrigerator model 10656584500, a truly bad compressor usually shows up as poor or no cooling even though the unit keeps trying to run, often with repeated clicking (start attempts) or unusual compressor noise patterns. Before condemning the compressor, we confirm airflow, control settings, and start components using the checks in the owner's manual.

Quick symptoms that point toward a compressor problem

• Refrigerator and freezer both warm, and temperatures do not recover after several hours
• Compressor is very hot to the touch after repeated run attempts (use caution)
• Repeated clicking every few minutes (start device trying to engage)
• Unit runs “all the time” but never gets cold enough
• You hear a high-pitched or pulsating sound that is new and cooling performance is dropping (compressor load changing)

Rule out common look-alikes first (fast checks)

Many “bad compressor” calls end up being airflow, defrost, or water/ice related noises. Check these first:

• Make sure air vents inside the compartments are not blocked by food packages
• Confirm the temperature controls are set correctly; for digital controls, cycle OFF then ON to reset
• Listen for normal operating sounds (evaporator fan moving air, refrigerant gurgle at cycle end, sizzling during defrost)
• If the issue is frost buildup and warming, inspect the defrost system components
• If the noise is a buzz during ice maker fill, that is typically the inlet valve opening, not the compressor

Common causes vs. what you usually observe

What you notice	More likely cause	What to check next
Warm fridge and freezer, compressor clicks on and off	Start components or compressor locked	Electrical diagnosis; consider run capacitor WPW10662129 as a related start component
Warm temps with heavy frost on evaporator cover	Defrost failure	Defrost parts such as refrigerator defrost bi-metal WPW10225581 and refrigerator heater WP2323198
Runs longer than older fridge but temps are OK	Normal high-efficiency operation	Confirm temps and door sealing; avoid frequent door openings

Why it matters

Replacing a compressor is a major sealed-system repair. Doing the quick checks above prevents unnecessary parts replacement and helps you target the real failure (controls, defrost, airflow, or start components) before committing to a high-cost repair.

If you do need parts for model 10656584500, order from the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

The most common problems we see on Kenmore refrigerators like model 10656584500 are cooling issues, water leaks, ice maker or dispenser failures, moisture buildup, and unusual noises. Many of these trace back to airflow restrictions, incorrect temperature settings, dirty seals, or a failing defrost or water-supply component; use the 10656584500 owner's manual for model-specific checks.

Most common symptoms and what usually causes them

• Not cooling or warm temperatures: controls set incorrectly for conditions, blocked air vents, or a defrost-related issue (ice buildup reducing airflow)
• Freezer too warm or low ice production: frequent door openings, heavy ice usage, or settings needing adjustment
• Interior moisture buildup: doors opened often, humid room air, blocked vents, or food not wrapped well
• Water leaking or puddles: clogged defrost drain, loose water line, or a seeping inlet valve
• Ice maker not working: water supply problem, failed ice maker assembly, or a valve that is not opening consistently

Quick checks we recommend first (fast, no parts)

• Confirm the refrigerator is plugged into a grounded 3-prong outlet and the breaker is not tripped.
• Make sure the refrigerator and freezer controls are not set to OFF.
• Recheck temperature settings; adjust the refrigerator control first, then fine-tune the freezer.
• Clear packages away from interior air vents to restore airflow.
• Reduce door-open time; adding a large amount of food can take several hours to stabilize.

Common part-related fixes for this model

If basic checks do not resolve the issue, these are frequent repair paths for 10656584500:

Problem area	What you may notice	Example part on this page
Water supply to dispenser/ice maker	No water, slow fill, hollow cubes	Refrigerator inlet valve W10408179
Ice production	No ice, irregular harvest	Ice maker assembly - refrigerator ice maker by whirlpool 4317943
Defrost system	Frost buildup, warm fridge section	Refrigerator defrost bi-metal WPW10225581 and refrigerator heater WP2323198
Water taste/flow	Bad taste, reduced flow	Genuine Kenmore refrigerator water filter EDR3RXD1

Why it matters

Cooling, moisture, and ice maker complaints often share the same root cause: restricted airflow or inconsistent water flow. Fixing the underlying cause protects food temperatures, reduces frost buildup, and helps the ice maker cycle normally.

For ordering, use the parts list for model 10656584500 on this page, or search by model number on Sears PartsDirect.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10656584500, the model number is printed on the model and serial number label located on the inside wall of the refrigerator (fresh food) compartment. You can confirm the exact label location and what it looks like in the owner's manual.

What to look for on the label

The label typically includes several fields together, so you can identify the right information quickly:

• Model number (for this unit, it starts with 106.)
• Serial number
• Purchase date (often a blank line to fill in)
• Brand and safety certification text

Quick steps to find it

1. Open the refrigerator (fresh food) door.
2. Look along the inside wall of the refrigerator compartment.
3. Find the sticker or plate that lists model and serial.
4. Write the model number down exactly as shown (including all digits).

Why the model number matters

We use the model number to match the correct Kenmore parts and diagrams for your exact refrigerator configuration (shelves, ice maker, water filter system, door parts). It also helps avoid ordering a similar-looking part that does not fit.

Common label locations (comparison)

Location	How common on side-by-side units	What you will see
Inside wall of refrigerator compartment	Very common	Model and serial label (best place to check first)
Inside freezer compartment	Sometimes	Model and serial label on liner wall
Behind the base grille or lower kickplate	Sometimes	Tech or product tag on some designs

Ordering parts once you have the model number

After you confirm the model number, you can order parts from the parts list for model 10656584500, or search by model on Sears PartsDirect. For water and ice issues, common matches for this model include the genuine Kenmore refrigerator water filter EDR3RXD1 and the refrigerator inlet valve W10408179.

Last updated: February 2026

Kenmore side-by-side refrigerators are typically 33 to 36 inches wide; for the exact overall width of Kenmore model 10656584500, use the dimensions listed in the 10656584500 owner's manual. When planning a cutout, include clearance for ventilation and door swing.

What to measure (so it fits the first time)

Measure in three places and use the largest number.

• Cabinet width: side panel to side panel with doors closed
• Overall width: widest point across the front (often includes handles)
• Opening width: the space between cabinets or walls where the unit slides in

Clearances to plan for (from the manual guidance)

The manual’s installation guidance calls for airflow space and extra room near walls.

• Leave 1/2 inch of space on each side and at the top for ventilation
• If installed next to a fixed wall, leave 2 inches minimum on the wall side (depending on the model) so the door can swing open
• If the refrigerator has an ice maker, allow extra space at the back for the water line connection

Quick planning table

Use this to sanity-check your opening; then confirm the exact width in the manual.

Measurement you need	Typical side-by-side range	Where it’s used
Cabinet width	33 to 36 in.	Cutout fit between cabinets
Overall width (with handles)	34 to 38 in.	Tight hallways, doorways, trim
Clearance at sides/top	1/2 in.	Airflow and efficient cooling

Why it matters

If the refrigerator is even slightly too wide for the opening, it can rub cabinets, prevent proper leveling, and restrict airflow. Proper clearance helps the compressor run efficiently and keeps temperatures stable.

Parts you might replace during an install

If you are also servicing the water and ice system while measuring, common parts for this model include the refrigerator water filter EDR3RXD1 and the refrigerator inlet valve W10408179. You can also search by model number on Sears PartsDirect.

Last updated: February 2026