Kenmore 11022292100 compact washer Parts

The exact cubic feet capacity for Kenmore compact washer model 11022292100 is typically listed in the specifications section of the product literature; for this model family, compact top-load washers are commonly in the about 2.0 to 2.5 cu. ft. range. We recommend confirming the exact number in the 11022292100 owner's manual.

How to confirm capacity for model 11022292100

Capacity is a tub-volume spec, so the most reliable way to confirm it is by checking the model’s published specs.

• Look in the Specifications or Product features section of the manual
• Check for wording like “capacity”, “tub volume”, or “cu. ft.”
• If the manual lists basket dimensions instead of capacity, use the measurement method below
• Use the full model number 11022292100 when matching any spec sheet

If you need to calculate capacity from tub measurements

If you can measure the inside of the wash basket, you can estimate capacity.

• Measure inside diameter of the basket (in inches)
• Measure usable depth to the normal fill line (in inches)
• Convert inches to feet (divide by 12)
• Use the cylinder formula: π × (radius in feet)² × (depth in feet)

Quick reference table (what to measure)

Measurement	Where to measure	Tip
Inside diameter	Across the basket interior	Measure wall to wall
Usable depth	Bottom to typical fill level	Do not measure to the rim
Radius	Diameter ÷ 2	Convert to feet before calculating

Why it matters

Washer capacity affects load size, cycle performance, and out-of-balance risk. Overloading a compact washer can also contribute to spin issues and extra wear on drive components like the coupling and clutch.

If you’re shopping for repair parts while you troubleshoot performance, you can order model-matched items from the parts list for this washer or search by model number on Sears PartsDirect.

Last updated: February 2026

Kenmore washer model numbers are structured so you can identify who built the washer and which design family it belongs to. For your Kenmore compact washer model 11022292100, the first three digits (110) are the manufacturer prefix, followed by digits that identify the base model and its specific variation; confirm the exact model and serial from the plate described in the owner's manual.

What each section of a Kenmore model number means

Most Kenmore washer model numbers follow this pattern:

• Prefix (first 3 digits): identifies the manufacturer (for example, 110)
• Base model digits (middle group): identifies the core platform or design series
• Variation digits (last group): identifies feature, color, or production variations
• Serial number (separate from model): helps date and track the specific unit for service and parts

Where to find the model number on the washer

We recommend matching the model number exactly before ordering parts.

• Look for the model and serial number plate on the washer cabinet
• Record both the model and serial numbers
• Use the full model number (all digits) when searching parts lists
• Keep the information with your purchase records for future reference

Why the model number matters for parts fit

Even small digit differences can change which parts fit your washer (agitator style, drive system, water valve type, and more). When you match the full model number, you avoid ordering the wrong replacement.

What you’re doing	Use this	Why it helps
Ordering replacement parts	Full model number (example: 11022292100)	Ensures correct part compatibility
Looking up diagrams	Full model number	Shows the correct component breakdown
Troubleshooting	Model plus symptom	Narrows likely causes and fixes

Common examples for this model family

For Kenmore model numbers that start with 110, common wear parts you may see listed for certain repairs include a motor coupling, drain pump, or agitator components. If your washer is not agitating or not draining, parts like the coupling 285753A or washer drain pump WP3363394 are typical items to check for this style of washer.

Ordering tip

Order replacement parts for Kenmore 11022292100 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

For the Kenmore 11022292100 compact washer, the practical “reset” is a power reset: turn the washer off, unplug it for 1 minute, then plug it back in and restart the cycle. This clears many temporary control and cycle interruptions (especially after a stall or stop).

Quick reset steps (safe for most situations)

• Press the timer/cycle knob in to stop the washer.
• Turn the cycle selector to Off.
• Unplug the power cord for 60 seconds.
• Plug the washer back in.
• Re-select your cycle and pull the timer knob out to start.

For normal start and stop operation details, follow the steps in the 11022292100 owner's manual.

If it still will not start, drain, or spin after the reset

A “reset” will not fix a mechanical or drain problem. Use these checks next:

• Lid closed: this style washer will not spin with the lid open.
• Drain hose height: keep the drain hose under 96 inches (2.4 m) above the floor.
• Kinks or clogs: straighten the drain hose and clear the standpipe or sink drain.
• Too many suds: reduce detergent; excessive suds can prevent proper draining and spinning.
• Unbalanced load: redistribute the load and try a spin again.

Common causes and what they point to

Symptom after reset	Most likely issue	What to check first
Won’t drain, wet loads	Drain restriction	Hose kink, clogged standpipe, pump obstruction
Won’t spin	Lid open or neutral drain behavior	Lid fully closed; allow time for drain-then-spin
Stops mid-cycle	Suds or overload	Use less detergent; wash smaller loads
Agitation issues	Drive components	Coupler, clutch, gear case (if agitation is weak/noisy)

Parts that commonly relate to “won’t drain” or “won’t agitate” complaints

If troubleshooting points to a failed component, these are common replacements for this model:

• Washer drain pump WP3363394
• Coupling 285753A
• Clutch 285785

Why it matters

A power reset clears a stuck timer position or temporary control interruption, but drain, spin, and agitation problems are usually caused by load balance, suds, hose setup, or worn drive parts. Ordering the correct part by model number prevents repeat failures; we list model-matched parts on this page and on Sears PartsDirect.

Last updated: February 2026

Most Kenmore washers average 10 to 15 years of service life with normal household use. For your Kenmore 11022292100 compact washer, consistent maintenance and avoiding overloads are the biggest factors that keep the drive system, drain pump, and suspension working longer (see the 11022292100 owner's manual).

Typical lifespan and what affects it

A washer’s lifespan is mainly driven by load size, cycle frequency, and how well the machine stays balanced.

• Usage level: daily loads wear parts faster than 3 to 5 loads per week
• Overloading: strains the motor, clutch, and gearcase
• Out-of-balance operation: accelerates wear on suspension and drive components
• Water quality: sediment can shorten inlet valve life
• Maintenance habits: periodic cleaning and inspection prevents small issues from becoming major repairs

Parts that commonly determine “end of life”

When a washer becomes noisy, won’t spin, or won’t drain, these are common repair points on this style of Kenmore top-load design.

Symptom	Common cause	Example part for this model
Won’t drain or leaves water in tub	Clogged or failing pump	Washer drain pump WP3363394
Agitates poorly or intermittently	Worn agitator dogs/cam	Agitator dog 80040
Won’t spin, loud during spin	Drive coupling or clutch wear	Coupling 285753A or clutch 285785
Oil leak, grinding, no agitation/spin	Gearcase wear	Gear case 3360629

How we recommend extending washer life

These steps match how this washer is designed to operate (fill, wash, drain, spin) and help reduce stress on the drivetrain.

• Keep loads evenly distributed to reduce vibration
• Use the right water level for the load size
• Avoid washing heavy, water-logged items alone (balance with similar items)
• Check hoses and screens periodically to protect the inlet valve
• Address early symptoms quickly (slow drain, burning smell, repeated off-balance)

Why it matters

A washer that is kept level and not overloaded typically avoids the most expensive failures (gearcase, basket drive, motor). Replacing a wear item early, such as a coupling or drain pump, often restores normal washing and spinning and helps the washer reach the full 10 to 15 year range.

If you decide to repair, you can order model-matched replacement parts from the parts list for Kenmore 11022292100, or search by model number on Sears PartsDirect.

Last updated: February 2026