Owner’s manual
Error Codes
How big is the Whirlpool model ED5LVAXWS01?
The Whirlpool ED5LVAXWS01 is a full-size side-by-side refrigerator with a typical capacity around 25 cu. ft. For exact exterior dimensions (height, width, depth) and clearance needs, we recommend confirming the specifications in the ED5LVAXWS01 owner's manual.
When customers ask how big a refrigerator is, it usually refers to one of these:
- Capacity (cu. ft.): how much food it holds
- Exterior size: height, width, depth (and depth with doors/handles)
- Installation clearance: space needed for airflow and door swing
- Door and drawer clearance: room to fully open doors and pull out bins
Most Whirlpool side-by-side refrigerators in this class fall into these common ranges.
| Spec | Typical range for side-by-side refrigerators | What to check for ED5LVAXWS01 |
|---|---|---|
| Capacity | 24 to 26 cu. ft. | Listed in the specifications section |
| Width | About 33 in. to 36 in. | Measure cabinet opening width |
| Height | About 65 in. to 71 in. | Include hinge height if noted |
| Depth | About 30 in. to 35 in. | Note “with handles” vs. “without handles” |
Use a tape measure and write down all three dimensions before ordering parts or planning a replacement.
- Measure width at the front and back of the opening
- Measure height to the lowest overhead cabinet or trim
- Measure depth from the back wall to the front edge of counters
- Add room for door swing so shelves and bins can open fully
- Leave space for airflow behind and above the refrigerator
Correct size and clearance helps the ED5LVAXWS01 cool properly, prevents door seal gaps, and avoids issues like warm temperatures, excess frost, or water/ice dispenser line pinching.
Last updated: January 2026
What is the most common problem with whirlpool refrigerators?
The most common Whirlpool refrigerator problems are cooling complaints (warm fridge or freezer, running constantly) and water or ice issues (slow dispenser flow, no ice). On the Whirlpool ED5LVAXWS01, these symptoms are often tied to airflow, defrost performance, or the water supply and filter system; see the ED5LVAXWS01 owner's manual for model-specific troubleshooting steps.
- Not cooling well or temperature swings: dirty condenser coils, blocked vents, or a weak evaporator fan.
- Running all the time: warm room conditions, dirty coils, door not sealing, or frequent door openings.
- No ice or small cubes: restricted water flow, low water pressure, or ice maker fill problems.
- Slow water dispenser: clogged filter, air in the water line after a filter change, or a supply issue.
- Frost buildup on the back wall: defrost system trouble (heater, thermostat, or control).
- Confirm the controls are turned on and set to normal temperatures.
- Make sure air vents inside both compartments are not blocked by food packages.
- Clean condenser coils and confirm the condenser fan area is clear of dust.
- If water flow is slow, replace the filter and flush the system.
- Check door closing and gasket contact all the way around.
| Symptom | Common part to check | What it affects |
|---|---|---|
| Slow water, no ice | Refrigerator water filter EDR3RXD1 | Water flow to dispenser and ice maker |
| No water to dispenser/ice maker | Refrigerator water inlet valve W10408179 | Opens to send water into the refrigerator |
| Frost buildup, warm temps | Refrigerator heater WP2323198 | Melts frost off the evaporator during defrost |
| Warm fridge section | Refrigerator evaporator fan blade WP2169142 | Moves cold air through the compartments |
Cooling and ice maker problems often share the same root causes: restricted airflow, heat not being removed efficiently, or restricted water flow. Fixing the basic maintenance items first prevents unnecessary part replacement and helps the refrigerator stabilize temperatures faster.
Last updated: January 2026
What does E5 timed ice making mean?
On Whirlpool model ED5LVAXWS01, an E5 “timed ice making” message points to the ice maker not completing a harvest or fill cycle in the expected time. In most cases, the fix is restoring proper water supply and ice maker operation, then checking the ice maker and inlet valve if the problem returns.
- Confirm the ice maker is turned ON (wire shutoff arm down or switch in the ON position, depending on style).
- Make sure the household water shutoff valve is fully open.
- Inspect the water line for a kink or pinch behind the refrigerator.
- If this is a new install or the ice maker was recently turned back on, allow 24 hours for the first ice and up to 72 hours for full production.
- Clear any jammed cube at the ejector area using a plastic utensil.
For the exact on/off style and operating notes for this model, follow the steps in the ED5LVAXWS01 owner's manual.
| What’s happening | What it usually means | What we do next |
|---|---|---|
| Small or hollow cubes | Low water pressure or restricted flow | Open shutoff fully, straighten line, replace clogged filter |
| No ice, dispenser water weak | Water supply issue or valve not opening | Check supply, then test/replace inlet valve |
| Ice maker cycles but no cubes | Fill problem or ice maker issue | Inspect fill tube for icing, consider ice maker replacement |
If the basic checks do not stop the E5 message, these parts are the most common next steps for ED5LVAXWS01:
- Refrigerator water filter EDR3RXD1 if the filter is overdue or flow is reduced.
- Refrigerator water inlet valve W10408179 if the valve is not opening consistently to fill the ice maker.
- Refrigerator ice maker 2198597 if the module is stalling during harvest.
Timed ice making errors are usually a water flow or fill-time problem. Fixing the supply, filter, or inlet valve prevents slow production, hollow cubes, and repeated ice maker cycling that can lead to more wear.
Last updated: January 2026
