Kenmore 11074602300 gas dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number label. For Kenmore model 11074602300, that label is located at the top inside the dryer door well; write down the full model number and serial number exactly as shown.

Where to look on the dryer

Check these common label locations first (most Kenmore dryers use one of them):

• Top inside the dryer door well (most common on 110-series dryers like 11074602300)
• Inside the door opening on the cabinet frame
• Rear panel near the top edge
• Side panel near the door opening (less common)

If the label is worn, use a flashlight and look for faint stamped or printed characters.

What to record (and why)

When you find the label, copy the information exactly. We recommend taking a photo, too.

• Model number (example: 11074602300)
• Serial number (used to identify production details)
• Purchase date (helpful for service history and maintenance planning)

Quick reference table

Item on label	What it’s used for	Example
Model number	Matching parts and diagrams	11074602300
Serial number	Identifying the exact production run	(varies)
Type (gas/electric)	Confirming correct repair and safety steps	Gas dryer

Why it matters

Kenmore model numbers can look similar, but parts like a door switch, belt, or thermostat can vary by model series and production run. Using the exact model number helps us match the correct replacement part the first time.

For the official location and product record section, use the 11074602300 owner’s manual.

A Kenmore gas dryer like model 11074602300 typically lasts 13 years with normal household use and routine vent cleaning. Keeping airflow strong and replacing wear parts early helps this dryer heat safely, dry faster, and avoid breakdowns.

What affects lifespan the most

• Vent restriction (long runs, crushed flex duct, lint buildup) increases heat stress
• Overloading strains the drum support system and belt
• High heat cycles used constantly accelerate wear on thermostats and sensors
• Ignoring noise (thumping, squealing) often leads to bigger repairs
• Poor door sealing can reduce airflow and drying performance

Maintenance schedule we recommend

Task	How often	Why it matters
Clean lint screen	Every load	Maintains airflow and drying time
Clean exhaust duct to outside	Every 6 to 12 months	Prevents overheating and long dry times
Check drum for unusual noise	Monthly	Catches roller/belt wear early
Inspect door seal and latch	Every 6 months	Helps proper airflow and safe operation

Parts that commonly wear as the dryer ages

These are normal wear items on many Kenmore gas dryers; replacing them when symptoms start usually extends service life:

• Dryer drum belt 341241 (drum turns slowly, squeals, or stops turning)
• Idler pulley WP691366 (squealing, belt slipping)
• Dryer operating thermostat WP3387134 (overheating or inconsistent heat)
• Dryer valve coil kit 279834 (heats briefly, then no heat)

Why it matters

A dryer can keep running past its average lifespan, but restricted airflow and worn drive parts raise operating temperatures and stress the motor, burner system, and safety thermostats. Preventive cleaning and timely part replacement protect performance and reliability.

For model-specific safety, venting, and care instructions, follow the owner's manual.

Last updated: March 2026

For Kenmore gas dryer model 11074602300, the most commonly needed replacement parts are the drum drive components, door switch and seals, and gas heat ignition parts. These items wear from normal use and are the first places we check when the dryer will not start, will not heat, or gets noisy.

Most common parts (and what they fix)

• Dryer drum belt 341241: drum will not turn, slipping, squealing
• Idler pulley WP691366: squealing, belt tension problems
• Dryer repair kit 4392065: common wear set for drum support issues (noise, rough drum rotation)
• Dryer door switch WP3406107: dryer will not start when door is closed
• Dryer door seal W10906683: poor airflow at the door, longer dry times, heat escaping
• Whirlpool dryer burner igniter kit 279311: no heat (igniter not glowing or not lighting burner)
• Dryer valve coil kit 279834: heats briefly, then stops heating

Quick symptom-to-part guide

Symptom	Most likely area	Parts to consider
Runs but no heat	Ignition or gas valve	Igniter kit, valve coils, radiant sensor
Starts then stops heating	Gas valve coils	Valve coil kit
Loud squeal or thump	Drum support/drive	Belt, idler pulley, repair kit
Will not start	Door/start circuit	Door switch, push-to-start switch

How we recommend confirming the right fix

1. Unplug the dryer and shut off the gas before opening panels.
2. Match the symptom to the table above.
3. Use the wiring diagram and troubleshooting steps in the owner's manual.
4. If you are testing electrical parts, use a meter and follow safe procedures.

Why it matters

Replacing the correct wear part restores airflow, drum movement, and safe burner operation. That prevents repeat failures like burned belts from a seized pulley, or repeated no-heat calls caused by weak gas valve coils.

Last updated: March 2026