Kenmore 11026422503 washer Parts

Your Kenmore washer model number is printed on the appliance’s model and serial tag; for Kenmore, it often starts with 110 (like 11026422503). On most top-load Kenmore washers, we find this tag under the lid or around the lid opening; use the exact model number to match parts and manuals.

Check these common locations first (wipe dust off the tag so every digit is readable):

• Under the lid, on the rim around the tub opening
• On the underside of the lid itself
• On the back panel near the power cord entry
• Along the rear edge of the control console (some designs)
• Inside the cabinet opening near the top (less common)

For Kenmore washers, the model number is usually a long string of digits; many are 11 characters and may begin with 110.

• Copy the model number exactly as shown (no spaces)
• Also record the serial number; it helps confirm production details when ordering parts
• If the tag is worn, take a clear photo and zoom in to verify each digit

Kenmore washers can look similar across multiple revisions, but internal components (like the lid switch, drain pump, or motor coupling) can differ. Using the exact model number helps us match the correct diagrams and replacement parts the first time.

Use the 11026422503 owner’s manual to confirm model/serial tag location and to reference operating and care details while you’re identifying the unit.

Last updated: February 2026

Yes; repairing a Kenmore washer is worth it when the fix is a common wear part and the total repair cost is clearly less than replacing the machine. For Kenmore model 11026422503, many frequent failures involve serviceable parts like the lid switch, drain pump, or motor coupling, which are typically cost-effective repairs.

We use these practical checkpoints before spending money:

• Repair it when the washer still fills, drains, and spins sometimes, and the issue points to a single part (switch, pump, coupling, clutch).
• Repair it when the cabinet and tub are solid (no severe rust, no recurring leaks).
• Repair it when the symptom is safety-related or “no start” and you can confirm the lid is closing and latching.
• Replace it when multiple major systems are failing at once (drive system plus leaks plus electrical issues).
• Replace it when the repair requires extensive teardown and you also have heavy corrosion or repeated water damage.

These are high-impact parts that often restore normal operation:

Follow these steps to avoid replacing the wrong component:

• Unplug the washer and confirm the lid closes firmly and the strike is not broken.
• Run a drain and spin; listen for the pump (a hum with no water movement often points to a blockage or failing pump).
• If the motor runs but the tub does not move correctly, suspect the coupling or clutch.
• Look for water under the washer after a cycle; leaks can change the repair decision.
• Use the troubleshooting section in the 11026422503 owner's manual to match symptoms to checks.

A targeted repair extends the life of a dependable Kenmore top-load platform and avoids the higher cost of a new washer plus delivery, installation, and haul-away. The manual also reminds us not to attempt repairs unless the instructions are understood and you have the skills to carry them out.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11026422503, consistent care (proper loading, correct detergent, and periodic cleaning) helps you reach the high end of that range and reduces wear on drive and drain components.

• Overloading (stresses the drive system and suspension)
• Unbalanced loads (increases vibration and spin wear)
• Water quality (sediment can shorten inlet valve life)
• Drain restrictions (overworks the drain pump)
• Cold-weather storage (water left inside can damage components)

Use the care steps in the 11026422503 owner's manual and keep these habits consistent:

• Leave the lid open after use to help the tub dry
• Run occasional hot washes (with an empty tub) to reduce residue
• Use the right amount of detergent; too much can cause buildup
• Level the washer on a solid floor to limit vibration
• If the washer is in a cold area, winterize it before temperatures reach freezing

A washer that is nearing end-of-life often shows early warning signs (slow drain, weak agitation, frequent off-balance). Catching those symptoms early can prevent secondary damage to the motor coupling, clutch, and gear case.

Last updated: February 2026