Kenmore 59675232402 refrigerator Parts

To level your Kenmore refrigerator model 59675232402, adjust the front leveling screws to raise or lower the front, then set the stabilizing legs so they rest firmly on the floor. Keep the front about 1/4 inch (6 mm) higher than the back to help the doors close properly (see the 59675232402 owner's manual).

• Protect vinyl or delicate flooring with cardboard or a rug.
• Do not use power tools for leveling.
• Remove the toe grille (pull outward to unclip).
• Remove the bottom hinge cover(s) (use a blunt tool in the notch to pry gently).
• Use a 3/8-inch hex head driver to turn the front adjustment screws on both sides.
• Use a carpenter’s level to confirm:
  • Front is about 1/4 inch higher than the rear.
  • Cabinet is level side-to-side.
• Turn the stabilizing legs clockwise until they are firmly against the floor.
• Reinstall hinge cover(s) and the toe grille (make sure the “top” marking is oriented correctly).

A refrigerator that is not level can cause door-closing and sealing problems, which leads to temperature swings, extra run time, and moisture buildup. Keeping the front slightly higher than the back improves door closure and overall cooling performance.

Last updated: January 2026

On the Kenmore 59675232402 bottom-mount refrigerator, the “bottom part” people mean is usually the machine compartment (also called the compressor compartment), which houses the compressor and other cooling-system parts; the very lowest piece underneath is often the base grille and the drain pan area.

• Machine compartment: The rear lower area where the compressor and condenser components sit.
• Compressor compartment: Another name for the machine compartment.
• Base grille / toe grille: The front lower grille that helps airflow and protects components.
• Drain pan: The pan underneath that collects defrost water so it can evaporate.
• Condenser coil area: The lower back area where heat is released.

The bottom section is where most of the heat removal and “power” of cooling happens.

Knowing the right name helps you troubleshoot and order the correct Kenmore refrigerator parts. For example, airflow around the machine compartment is important; our manual notes to allow clearance behind the machine compartment cover for proper air circulation and to clean condenser coils periodically. Check the 59675232402 owner's manual for the exact locations and care steps.

• Unplug the refrigerator before removing any covers.
• Keep the base grille area clear of dust and pet hair.
• Make sure the refrigerator is level so doors close tightly.
• If you see water underneath, inspect the drain pan and defrost drain path.
• If cooling is weak and the unit is noisy, the machine compartment fan or compressor area may need diagnosis.

Last updated: January 2026

For Kenmore model 59675232402, the most reliable “reset” is a power reset: unplug the refrigerator for 5 to 10 minutes, then plug it back in and allow temperatures to stabilize. For control-related issues, follow the control and OFF-setting steps in the 59675232402 owner's manual.

• Power reset (hard reset): Unplug 5 to 10 minutes, then restore power.
• Control OFF reset: Press the Refrigerator or Freezer temperature pad until "--" appears (control OFF), then turn it back on and set temps.
• Defrost wait reset: If lights are on but the compressor is off, wait about 40 minutes; the unit may be in defrost.
• After reset: Give the refrigerator 24 hours for temperatures to stabilize before making more changes.

1. Press the Refrigerator or Freezer temperature pad until a dash ("--") shows.
2. Wait 1 minute.
3. Press the same pad to set a normal temperature again.
4. Avoid changing either control more than one number at a time; wait for stabilization.

A reset only clears temporary control glitches. If the refrigerator is in defrost, has restricted airflow, or has a cooling-system issue, resetting will not correct the root cause. Using the correct control steps also prevents temperature swings.

Helpful related reading: Kenmore 106 model refrigerator error codes

Last updated: January 2026

On Kenmore model 59675232402, dH (often shown as Er dH) indicates a defrost heating problem: the refrigerator is not sensing the expected temperature rise during the defrost cycle. This can lead to frost buildup on the evaporator and warmer-than-normal temperatures.

• Unplug the refrigerator before removing panels or handling wiring.
• Check for heavy frost on the freezer back wall or behind the evaporator cover.
• Make sure doors close fully and gaskets seal; warm air leaks can mimic defrost issues.
• Confirm the unit has proper airflow clearance (tight installs can affect performance).
• Restore power and monitor temperatures after any change.

A dH/Er dH condition is usually tied to the defrost circuit or airflow across the evaporator.

• Inspect the evaporator area for ice buildup that blocks airflow.
• Check the defrost thermostat and heater circuit for continuity (with power disconnected).
• Verify the control is sending power to the defrost heater during a forced defrost test (procedure varies by model).
• If the evaporator fan is not moving air, address the fan motor/blade before chasing defrost parts.

For model-specific control locations, panel removal, and safety notes, use the 59675232402 owner’s manual.

When defrost heat is not working, frost builds up on the evaporator coil, airflow drops, and the refrigerator section often warms first. Fixing the root cause prevents food spoilage and reduces compressor run time.

Last updated: January 2026