Kenmore 11047571601 washer Parts

The exact tub capacity (cubic feet) for Kenmore washer model 11047571601 is listed in the product specifications section of the 11047571601 owner's manual. Most Kenmore 110-series front-load washers of this design are typically in the 3.0 to 4.0 cu. ft. range.

We recommend using the model-specific documentation because capacity can vary within the Kenmore 110 family.

• Open the 11047571601 owner's manual
• Look for Specifications, Product dimensions, or Capacity
• If the manual lists drum volume (liters), convert to cubic feet (see below)
• If you see multiple capacities, use the one tied to your exact model number 11047571601

If your manual lists drum volume in liters, this conversion helps:

Capacity affects how much laundry you can wash per load, how much HE detergent to use, and how likely the washer is to go out of balance during high-speed spin.

If you are chasing balance or spin issues (often mistaken for a “too small” or “too big” tub), check for worn suspension components and confirm the washer is level. A failing washer shock absorber W10739670 can also contribute to excessive vibration during spin.

Last updated: January 2026

For a Kenmore washer like model 11047571601, a hard reset is usually as simple as removing power long enough for the electronic control to fully power down, then restoring power and running a quick test cycle. For model-specific button sequences and diagnostics, follow the steps in the 11047571601 owner’s manual.

• Press Power/Cancel to stop the cycle.
• Unplug the washer (or switch OFF the breaker).
• Wait 2 minutes.
• Restore power.
• Open and close the door once, then select a normal cycle and press Start.

These steps help clear a control glitch, a door-lock issue, or a drain problem that can look like a control failure.

• Confirm the outlet has power (try a lamp) and the breaker is fully reset.
• Make sure the door closes firmly; a weak latch can prevent starting.
• If the tub is full of water, run Drain/Spin; a drain restriction can block operation.
• Check for a kinked drain hose or an overstuffed load causing imbalance.
• If you see leaks or the washer will not drain, inspect the water pump WPW10730972 area for debris (coins, lint, small socks).

A hard reset clears temporary control-board logic errors without replacing parts. If the same problem returns quickly, the washer is usually reacting to a real condition (door-lock not engaging, drain not clearing, or an out-of-balance load) rather than needing repeated resets.

Last updated: January 2026

On Kenmore washer model 11047571601, we force a drain by canceling the cycle, then manually draining through the pump cleanout (if equipped) and clearing any blockage in the drain path. This safely removes standing water so you can restart or service the washer.

• Unplug the washer (or switch off the breaker).
• Turn off both water supply valves.
• Place towels and a shallow pan under the lower front access area.
• Open the pump cleanout access and slowly loosen the cap to let water drain in a controlled way.
• Check the drain hose for kinks, pinches, or a clog at the standpipe.
• Reinstall the cap tightly, restore power, then run a Drain/Spin cycle.

If your 11047571601 does not have a pump cleanout access, we drain by lowering the drain hose into a shallow pan (or using a wet/dry vacuum on the hose) and then clearing the obstruction.

Most “won’t drain” problems come from a restriction or a failed drain component. Check these common causes:

• Coins, socks, or lint blocking the pump or pump inlet
• A kinked or crushed drain hose
• Suds lock from too much HE detergent
• A failed drain pump motor
• A door lock issue that prevents the washer from entering drain/spin

Standing water can leak, cause odor, and strain the pump and control system. Draining first also makes any repair (pump, hose, door boot) cleaner and safer.

For model-specific access steps and panel removal details, follow the 11047571601 owner's manual.

Last updated: January 2026

To turn off Control Lock on your Kenmore washer model 11047571601, press and hold the button labeled for Control Lock for about 3 seconds until the lock indicator turns off. The same 3-second press typically turns Control Lock back on.

• Look for a control panel label that says “Control Lock” or “Hold 3 sec”.
• Press and hold that specific button for 3 seconds.
• Watch for the lock light/icon to turn off or for a tone to sound.
• Try pressing Start or changing a cycle to confirm the panel responds.
• If the washer is running, pause the cycle first, then try the 3-second hold again.

On many Kenmore Elite washers, Control Lock is assigned to one key (or a key combination) printed right on the console. Use the control panel diagram and feature descriptions in the 11047571601 owner’s manual to identify the exact button for your console layout.

These checks solve most “stuck lock” situations:

• Power reset: Unplug the washer (or switch off the breaker) for 2 minutes, then restore power and try the 3-second hold.
• Stuck key: Press the Control Lock key a few times to make sure it is not physically stuck.
• Wet console: If the panel is damp, dry it and wait 10 to 15 minutes, then retry.
• Door not closed: Close the door firmly; some models limit inputs when the door is not fully latched.
• Control issue: If the panel does not respond to any keys, the main control can be the cause (for this model, see electronic control WPW10163007).

Control Lock prevents accidental cycle changes and stops kids from starting the washer. Knowing how to toggle it quickly helps when the washer looks “dead” but is simply locked.

Last updated: January 2026