Maytag LAT9406AAM washer/dryer Parts

You can order replacement parts for your Maytag LAT9406AAM washer through Sears PartsDirect by matching the exact model number and then selecting the part you need. For correct part identification, we recommend using the diagrams and part lists in the LAT9406AAM owner's manual.

Best way to order the right part

• Confirm the full model number is LAT9406AAM (the manual notes it’s on the data plate on the top edge of the control panel).
• Use the parts diagrams to identify the exact component name.
• Match by part ID when available (this helps avoid look-alike parts).
• Order common wear items proactively if symptoms point to them.
• Keep your model and serial number handy for service or support.

Common parts customers order for this model

What you’re fixing	Common part to check	Example part ID
Washer will not start or stops when lid opens	Lid switch	W10820036 or WP207166
Washer won’t spin or has burning rubber smell	Drive belt	12112425
Overfilling or incorrect water level	Water switch	WP22001656

If your issue is “won’t start,” the lid switch W10820036 is one of the first parts we check because the washer will not run if the lid safety circuit is open.

Why it matters

Ordering by model number and part ID reduces returns and downtime. The manual also includes a “Before You Call” section that can help you confirm whether a part is actually the cause before you buy.

Last updated: February 2026

Most Maytag washers average 10 to 13 years of service life in normal home use; a Maytag LAT9406AAM can often reach that range when it is leveled correctly, not overloaded, and maintained using the care steps in the LAT9406AAM owner's manual.

Typical lifespan ranges (what to expect)

Washer life is driven mostly by load size, cycle frequency, water quality, and how well the machine stays balanced.

• Average Maytag washer lifespan: 10 to 13 years
• Common whole-industry range: 8 to 12 years
• Heavy use (large family, daily loads): closer to the low end
• Light use (few loads per week): closer to the high end

What shortens washer life fastest

• Regular overloading (extra-heavy towels, bulky bedding)
• Running out of level (excess vibration and walking)
• Hot water issues (poor cleaning leads to rewashing and extra wear)
• Gritty or hard water (more abrasion on seals and bearings)
• Ignoring early symptoms (squealing, burning rubber smell, slow drain)

Parts that commonly show wear first

If your washer still fills and drains but struggles to agitate or spin, these are common wear areas on many belt-drive Maytag designs.

Symptom	Common wear area	Example part for LAT9406AAM
Won’t spin or stops when lid opens	Lid safety circuit	Lid switch W10820036
Squealing or burning rubber smell	Drive system	Washer drive belt 12112425
Loud rumble during spin	Bearings/tub support	Inspect per LAT9406AAM owner's manual

Why it matters

Knowing the typical lifespan helps you decide whether to maintain, repair, or plan a replacement. If your LAT9406AAM is near the 10 to 13 year mark, fixing a single wear item (like a lid switch or belt) often restores reliable operation and prevents bigger failures caused by repeated restarts and unbalanced spinning.

Last updated: February 2026

The most common Maytag washer problem is a no-spin or no-drain condition. On the Maytag LAT9406AAM, this is most often tied to a lid switch issue, a drive system problem (belt or pulley), or a drain restriction that prevents the washer from completing the cycle.

Quick checks we recommend first

• Make sure the load is evenly distributed; an unbalanced load can stop or limit spin.
• Confirm both water faucets are fully open and hoses are connected correctly.
• If filling seems weak, disconnect the inlet hoses and clean the inlet screen filters.
• Verify the temperature selector is set directly on a setting (not between settings).
• Check that the washer is level and the rubber feet are installed on the leveling legs.

Most common causes and what you’ll notice

Symptom	Most likely cause	What to check next
Won’t spin, may still fill/agitate	Failed lid switch	Test lid switch operation; inspect actuator/lever and wiring; replace if intermittent (lid switch W10820036)
Agitates but won’t spin, burning rubber smell	Worn or broken belt	Inspect belt for glazing, cracks, looseness (washer drive belt 12112425)
Drains slowly or not at all	Drain restriction	Check drain hose for kinks; clear clogs; verify standpipe height and flow
Excessive vibration or “walking”	Leveling or load balance	Re-level, confirm rubber feet, reduce bulky single-item loads

Why it matters

A washer that cannot drain or spin leaves clothes soaked and can strain the motor, belt, and bearings over time. Catching a failing lid switch or worn belt early is one of the simplest ways to prevent bigger, more expensive repairs.

Model-specific tip for LAT9406AAM

We use the troubleshooting and “Before You Call” guidance in the LAT9406AAM owner's manual to narrow problems down by symptom (fill, agitate, drain, spin) before replacing parts.

Last updated: February 2026

Yes, it’s usually worth fixing a Maytag LAT9406AAM washer when the problem is a single, common failure (like a lid switch or drive belt) and the total repair cost stays well below the price of a comparable replacement washer. If you’re facing repeated breakdowns or major mechanical wear, replacement is the better value.

Quick way we decide: repair vs. replace

• Repair when the washer still fills, drains, and spins, but has one clear symptom (no spin, no start, intermittent stop).
• Replace when multiple systems are failing (leaks plus no spin plus loud bearing noise) or repairs keep stacking up.
• Start with the basics in the LAT9406AAM owner's manual “Before You Call” style checks (power, water supply, hose screens, leveling).

Common “worth fixing” repairs on this model

These are typical, targeted fixes that often restore normal operation:

• Lid won’t start spin or washer stops mid-cycle: check the lid switch W10820036
• Washer won’t run with lid closed or acts intermittent: check the washer lid switch WP207166
• Burning rubber smell, weak agitation, or no spin with motor running: inspect the washer drive belt 12112425
• Out-of-balance shaking: verify leveling legs and rubber feet are installed
• Slow fill or temperature issues: clean inlet hose screens and confirm hot water is at least 120°F at the tap

Cost and effort comparison

Scenario	Typical outcome	Usually worth it?
Single electrical/safety part failure (lid switch)	Fast diagnosis, low parts cost	Yes
Wear item (belt)	Moderate DIY effort, predictable fix	Yes
Multiple symptoms across fill, drain, spin	Longer troubleshooting, higher risk of repeat repairs	No
Loud roaring/grinding during spin (bearing wear)	Major teardown, higher labor	No

Why it matters

A focused repair keeps a dependable Maytag washer running for a fraction of replacement cost, but chasing multiple failures can turn into repeated downtime and escalating labor. Using the manual’s troubleshooting steps first helps you avoid replacing good parts.

Last updated: February 2026