Kenmore 10656866600 side-by-side refrigerator Parts

To replace the ice maker in your Kenmore 10656866600 side-by-side refrigerator, we shut off power, remove the ice bin, disconnect the ice maker wiring and fill tube, swap in the new assembly, then restore power and turn the ice maker back ON. Use the owner's manual for the exact switch location and bin removal details.

Before you start (safety and prep)

• Unplug the refrigerator or switch OFF the circuit breaker.
• Turn OFF the water supply to the refrigerator.
• Empty the ice bin; never use anything sharp to break up ice.
• Protect the floor with towels; a small amount of water can spill.
• Keep screws organized so the ice maker mounts squarely.

Replacement steps (typical for this Kenmore side-by-side)

1. Remove the ice storage bin: press the release button, lift up, and pull the bin out.
2. Turn the ice maker OFF using the freezer On/Off switch (top right area in the freezer compartment on this model family).
3. Remove the ice maker mounting screws and support the ice maker as you loosen the last screw.
4. Disconnect the wiring harness plug.
5. Pull the ice maker forward and free the fill tube from the rear cup/funnel area.
6. Install the replacement ice maker: seat the fill tube correctly, reconnect the harness, and tighten mounting screws.
7. Reinstall the ice bin, turn the ice maker ON, restore water, then restore power.

Quick checks after installation

• Confirm the ice maker switch is ON (left position on many versions).
• Make sure the ice bin is fully seated; the door sensor area must not be blocked.
• Verify the fill tube is not kinked, misaligned, or iced shut.
• Discard the first batch or two of ice after service.

Common symptoms and what they usually mean

Symptom	Most common cause	What to check first
No ice after 24 hours	Ice maker OFF or bin not seated	Switch position; bin installed correctly
Small or hollow cubes	Low water flow	House shutoff valve fully open; filter condition
Ice clumps in bin	Infrequent use	Empty and wash bin; dry thoroughly

Why it matters

A correctly mounted ice maker and properly seated ice bin let the automatic shutoff sensor work normally, preventing overfilling and helping maintain steady ice production.

Last updated: February 2026

On Kenmore model 10656866600, a bad compressor usually shows up as no cooling (or weak cooling) along with unusual compressor behavior such as repeated clicking, loud buzzing, or the unit running almost constantly without reaching temperature. Use the owner's manual to rule out normal operating sounds and basic setup issues first.

Quick checks we use before blaming the compressor

• Confirm the refrigerator has had 24 hours to cool after a new install or being unplugged.
• Make sure controls are on and not set to OFF.
• Listen for normal sounds (pulsating, gurgling, popping) that can be mistaken for failure.
• Check whether the evaporator fan is running; airflow problems can mimic compressor trouble.
• Look for warm freezer and fresh food sections at the same time (often points to sealed-system or compressor/start issues).
• Verify doors are closing and sealing; air leaks can cause long run times.

What symptoms point strongly to a compressor or start-device problem

A compressor problem is likely when you see a combination of these:

Symptom	What it often means	What to do next
Repeated clicking every few minutes	Compressor overload or start device cycling	Unplug, inspect start components; consider service diagnosis
Compressor runs but cooling stays poor	Weak compressor or sealed-system restriction	Professional sealed-system testing
Compressor is very hot and shuts off	Overload trip from high amps or poor ventilation	Clean condenser area; check airflow; service test
Fridge runs nearly nonstop	Not reaching set temp due to cooling system issue	Check door seals, condenser cleanliness, fan operation

Rule out common non-compressor causes first

These issues are more common than a failed compressor:

• Dirty condenser coils or blocked airflow around the cabinet
• Frost buildup from a defrost problem (a failed defrost thermostat can contribute; see refrigerator defrost bi-metal thermostat WPW10225581)
• Evaporator fan problems (noise, no airflow, warm fridge with cold-ish freezer)
• Door gasket leaks and frequent door openings

Why it matters

Compressors are part of the sealed cooling system; misdiagnosing one can lead to unnecessary cost. The manual also notes that high-efficiency compressors can run longer and make new sounds, so confirming symptoms prevents replacing the wrong part.

Last updated: February 2026

To identify your Kenmore refrigerator model, we look for the model number on the appliance’s ID label, then match that number when selecting parts and documentation. For this refrigerator, the model number format looks like 10656866600, and the exact model is shown in the owner's manual.

Where to find the model number label

On most Kenmore side-by-side refrigerators, the model and serial tag is in one of these spots:

• Inside the fresh food (refrigerator) compartment on a side wall
• On the ceiling area inside the refrigerator section
• Behind or beside the crisper drawers (you may need to pull a drawer out)
• Along the door frame edge (visible when the door is open)
• Near the lower front area behind the toe grille or kick plate

How to read the model number once you find it

Use the full model number exactly as printed (letters, numbers, and any dots). That full number is what ensures the right fit for parts like a water filter, ice maker, or door gasket.

Quick checks

• Match every character: even one missing digit can point to a different parts list.
• Use the full number: “106…” alone is not enough; use the complete model.
• Write down the serial number too: it helps when comparing production variations.

Why it matters for parts and troubleshooting

Kenmore model numbers often share similar styling across multiple revisions. Using the exact model number helps us match the correct component design, mounting points, and electrical connectors.

What you’re doing	Why the model number matters
Ordering a water filter	Ensures the correct filter style and cap fit
Replacing an ice maker	Prevents wiring and mounting mismatches
Fixing cooling issues	Helps match the right control and fan parts

Example: common model-specific parts you may match by model number

If your parts search leads you to these items for Kenmore 10656866600, the model number is doing its job:

• Genuine Kenmore refrigerator water filter EDR3RXD1
• Refrigerator ice maker WPW10190961
• Refrigerator temperature control WP2315562

Last updated: February 2026