Kenmore 66513273K115 undercounter dishwasher Parts

To hard reset your Kenmore dishwasher model 66513273K115, we recommend using the control-panel reset sequence (often called a “cancel/drain” reset) and then restoring power for a short period; this clears a stuck cycle and reboots the electronic control. For the exact button sequence for your console, use the 66513273K115 owner's manual.

Quick hard reset steps (most Kenmore dishwashers)

• Press Cancel/Drain once, then close the door and wait about 2 minutes for the drain to finish.
• If the dishwasher is still unresponsive, turn off power at the breaker (or unplug) for 3 minutes.
• Restore power and wait 30 seconds.
• Start a short cycle and listen for fill and wash action.
• If the controls are locked, hold Control Lock (or Lock) for 3 seconds, then retry.

If your panel uses a “heated dry” style reset

Some Kenmore-built dishwashers use a keypad sequence such as Heated Dry, Normal, Heated Dry, Normal (or similar). Use the exact sequence listed in the 66513273K115 owner's manual so you press the correct keys for your specific console.

What to check if the reset does not work

• Power supply: confirm the breaker is fully reset and the outlet has power.
• Door latch: the door must latch firmly or the control will not run a cycle.
• Water supply: verify the shutoff valve is open and the inlet line is not kinked.
• Drain path: clear the sink/disposer connection and check for a high loop in the drain hose.
• Control issue: if the panel lights up but won’t start, the electronic control may be failing.

Symptom after reset	Most likely cause	Common next step
Won’t power on	No power, loose wiring	Verify breaker/outlet, inspect harness
Powers on, won’t start	Door not latched, control lock	Reseat door, unlock controls
Starts then drains and stops	Drain restriction or stuck float	Clear drain path, check float
Runs but acts erratic	Control or keypad problem	Consider replacing the control

Why it matters

A hard reset clears a stalled program and forces the control to reboot, which often fixes “won’t start,” “stuck on drain,” or unresponsive keypad issues without replacing parts.

Last updated: January 2026

For Kenmore undercounter dishwasher model 66513273K115, the model and serial tag is typically on the tub opening where the door closes (along the left or right inner frame) or on the side wall just inside the door. Use the exact model number from that tag when ordering parts.

Where to look on model 66513273K115

Check these common label locations first:

• Left or right inner door frame (door jamb area)
• Top rim of the tub opening (near the latch)
• Inside the tub on the left or right wall near the front
• Along the inner edge of the door (less common)
• Behind the toe-kick panel area (occasionally, depending on installation)

For diagrams and the exact identification format used for this model, use the 66513273K115 owners manual.

What the model tag looks like (and what to write down)

Most Kenmore dishwashers use a paper label or metal plate with multiple lines. Record:

• Model number (example: 66513273K115)
• Serial number (helps match production run details)
• Type or engineering code (if shown)

Quick check table

Item on tag	Why it matters	Example
Model number	Ensures correct part fit	66513273K115
Serial number	Helps confirm version changes	Varies
Brand	Confirms parts family	Kenmore

If the label is missing or hard to read

Use these practical steps to recover the model information:

• Wipe the area with a damp cloth; grease can hide faint print
• Use a flashlight and take a close-up photo, then zoom in
• Look for an imprint outline where a label used to be
• Check purchase paperwork or installer notes (often lists the full model)
• Compare your control panel style and rack layout to the diagrams in the 66513273K115 installation guide

Why it matters

Kenmore model numbers can look similar, but small differences change parts like the water inlet valve, drain pump, spray arm, or heating element. Using the exact model number prevents ordering a part that mounts differently or uses a different electrical connector.

Last updated: January 2026

On the Kenmore 66513273K115 Quiet Guard undercounter dishwasher, the filter is in the bottom of the tub, under the lower rack, around the sump area. You access it by pulling out the lower rack and lifting or twisting the filter parts out for cleaning (then reinstalling them fully seated).

How to find and remove the filter

• Turn the dishwasher off; let the unit cool if it just ran.
• Pull the lower rack straight out and set it aside.
• Look at the tub floor near the center, around the sump (the lowest area where water collects).
• Remove the filter components (some lift out; some twist to unlock depending on the filter style).
• Rinse the filter under warm water; use a soft brush to remove grease and debris.

For the exact filter style and removal steps used on model 66513273K115, follow the diagrams and instructions in the 66513273K115 owner’s manual.

Which filter part do I need?

This model commonly uses a removable filter cup and a separate screen style filter. If your filter is cracked, won’t seat, or is missing pieces, replacement is usually the right fix.

What you see	What it usually means	What to do
Standing water and debris on tub floor	Filter clogged or not seated	Clean and reinstall filter; verify it sits flat
Grit on glasses	Filter dirty or wash system not circulating well	Clean filter; check spray arms for clogs
Filter won’t lock or sits loose	Worn or damaged filter parts	Replace the filter component

If you need the filter cup for this dishwasher, match your part by model number and use the correct listing such as dishwasher filter W10872845 or dishwasher filter WPW10463906.

Why it matters

A clean, properly installed dishwasher filter helps the circulation pump move water efficiently, improves cleaning performance, and reduces odors caused by trapped food soil.

Last updated: January 2026

Common problems we see on Kenmore dishwashers like model 66513273K115 are not draining, not starting, poor cleaning, leaking, and not drying. Most of these trace back to clogs (filter, hose, pump), a door-latch or control issue, or a heating and airflow problem.

Most common symptoms and what usually causes them

• Won’t drain or drains slowly: clogged filter, blocked drain hose, failed drain pump
• Won’t start: door not latching, control lock enabled, power supply issue, failed electronic control
• Dishes still dirty: clogged spray arm, filter packed with debris, low water fill, wrong detergent, hard water
• Leaks: loose hose connections, worn door seal area, cracked sump or hose
• Not drying: heater circuit issue, vent problem, rinse aid missing, cycle selection

Quick checks you can do first (no parts swapping)

1. Cancel the cycle and listen for the drain portion; a loud hum with no drain often points to a restriction or pump issue.
2. Clean the filter area and remove any glass, labels, or food debris.
3. Inspect the drain hose routing for kinks and confirm the high loop/air gap setup.
4. Spin and rinse the spray arms; clear blocked jets.
5. Run hot water at the sink for 30 to 60 seconds before starting a cycle to improve wash performance.

Parts that commonly fix these issues on 66513273K115

Symptom	Common part to inspect	What it affects
Not draining	Dishwasher drain pump WPW10348269	Pushes water out to the disposer/drain
Poor cleaning	Dishwasher spray arm WPW10491331	Water distribution and spray pressure
Not drying	Element assembly W10518394	Heats water and supports drying performance
Leaking from below	Dishwasher sump and seal assembly WPW10455268	Seals and directs water through the sump

Why it matters

A dishwasher that is not draining or cleaning well often gets worse quickly; standing water and debris can strain the pump, reduce wash pressure, and lead to odors. Catching a clog early is usually the simplest, lowest-cost fix.

Where to confirm model-specific steps

Use the 66513273K115 owner's manual for cycle behavior, indicator meanings, and cleaning instructions; use the 66513273K115 installation guide to verify correct drain hose routing and connection requirements.

Last updated: January 2026