Kenmore 10657026602 side-by-side refrigerator Parts

For Kenmore model 10657026602, the model number by itself usually does not state the exact cubic-foot capacity. The reliable way is to look up the capacity in the product specs section of the owner's manual, or calculate it from the usable interior measurements (refrigerator plus freezer).

Fast ways to get the cubic feet

• Check the capacity/specifications section in the owner's manual.
• Look for a tech/spec sheet stored on the refrigerator (commonly behind the base grille or inside a control housing).
• Measure the usable interior space and calculate cubic feet.
• If you are comparing sizes for fit, measure the outside cabinet dimensions separately (capacity and exterior size are not the same).

How to calculate cubic feet (DIY method)

1. Empty one compartment (fresh food or freezer) so you can measure accurately.
2. Measure usable interior:
   • Width (inches)
   • Depth (inches) (do not include door bins)
   • Height (inches)
3. Multiply: width x depth x height to get cubic inches.
4. Convert to cubic feet: cubic inches ÷ 1728.
5. Repeat for the other compartment and add them together.

Quick conversion table

What you have	Convert to cubic feet
Cubic inches	Divide by 1728
Cubic feet	Multiply by 1728 to get cubic inches

What the model number can and cannot tell you

Kenmore model numbers help identify the correct parts list, features, and documentation, but they are not a dependable “capacity code.” Two similar-looking model numbers can have different interior layouts (ice maker, dispenser housing, shelving) that change usable volume.

Why it matters

Cubic feet is most useful for comparing storage capacity between refrigerators. For installation planning (door swing, clearance, and cabinet opening), exterior measurements matter more than cubic feet, so we recommend using the dimensional guidance in the owner's manual.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10657026602, the water filter is located in the base grille at the bottom front of the refrigerator. You access it from the front by opening the grille area and using the filter cap/eject mechanism to remove the cartridge (see the owner's manual).

How to find and remove the filter (base grille style)

We recommend these steps for the 10657026602 water filtration system:

• Locate the base grille along the bottom front of the refrigerator.
• Look for the filter cap in the grille area.
• Press the eject button (if equipped) and pull the cap outward to remove the filter.
• Turn the cap counterclockwise to remove it from the old filter.
• Install the cap on the new filter, then insert and lock it in place.
• Flush the system by dispensing water for several minutes (or until water runs clear).

The replacement filter that fits this model

The manual lists the base grille replacement filter as part number 9030. On this model page, the matching replacement is genuine Kenmore refrigerator water filter EDR3RXD1.

Item	What you will see	What it does
Filter location	Base grille (bottom front)	Houses the water filter cartridge
Filter cap	Attached to the cartridge	Locks the filter into the grille housing
Status light	On the control panel	Reminds you when to replace the filter

Why it matters

A correctly installed water filter helps maintain water flow to the dispenser and ice maker, and it reduces the chance of taste and odor issues. Keeping the filter cap is important because you reuse it when you install the next cartridge.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10657026602, the model number is printed on the refrigerator’s identification label (the same label that lists the serial number). We use that model number to match the correct parts list and the right Kenmore documentation for your unit; see the owner's manual.

Common places to check first

Look for a paper or foil label in these typical spots on a side-by-side refrigerator:

• Inside the fresh food (refrigerator) compartment on a side wall
• Along the top interior frame near the ceiling of the refrigerator section
• On the door jamb area (where the door seals against the cabinet)
• Behind the base grille area near the floor (less common)
• On the back exterior of the cabinet (least convenient)

What the label looks like and what to write down

The ID label usually includes both a model number and a serial number.

Item	What it’s used for	Example format
Model number	Ensures parts fit and diagrams match	10657026602
Serial number	Helps identify production details	Letters plus numbers

Why it matters

Kenmore refrigerators can look similar across many model families. Using the exact model number (like 10657026602) prevents ordering the wrong items such as a water filter, ice maker, or inlet valve.

Quick tip if you’re ordering parts

Once you find the model number, match it to the parts list for 10657026602. Common replacements for this model include the genuine Kenmore refrigerator water filter EDR3RXD1 and the refrigerator ice maker 2198597.

Last updated: February 2026

If your Kenmore 10657026602 side-by-side refrigerator ice maker isn’t making ice, the most common causes are the ice maker being switched OFF, the freezer door or ice bin not seated correctly (which stops ice production), or a water supply problem such as a closed shutoff valve or kinked water line. Confirm the on/off switch location and bin seating steps in the owner's manual.

Quick checks we recommend first

• Make sure the ice maker On/Off switch is set to ON (left) in the freezer compartment.
• Confirm the freezer door closes completely; an open door can stop ice production.
• Reseat the ice storage bin firmly; removing the bin or opening the “flipper door” sensor cover stops the ice maker.
• Verify the refrigerator is connected to the water supply and the shutoff valve is fully open.
• Inspect the water source line for kinks; straighten the line to restore flow.
• If this is a new install or the ice maker was just turned on, wait 24 hours for ice to start; allow up to 72 hours for full production.

Water and filtration issues that stop ice

A restricted filter or low water flow can prevent the mold from filling correctly.

Symptom	What it usually points to	What to do
No ice at all	Water supply off or line kinked	Open valve; straighten line
Small/hollow cubes	Low water flow or restriction	Check line; replace filter
Gray/dark ice	Filter needs flushing	Flush system; replace filter if needed

If your filter is due, use the correct replacement for this model, the genuine Kenmore refrigerator water filter EDR3RXD1.

If the ice maker still won’t fill

If the supply line is good and the ice maker is ON, the next common failure is the valve that feeds water to the ice maker.

• Listen for a brief “fill” sound after a harvest cycle.
• Check for a frozen fill tube (ice blockage) and thaw it with warm air (no sharp tools).
• If there’s no water fill and household water pressure is good, test/replace the refrigerator inlet valve W10408179.

Why it matters

When the bin is out of position or the door is not fully closed, the ice maker’s sensor system can intentionally stop production. Water flow problems then compound the issue by preventing proper fills and normal cube size.

Last updated: February 2026

The most common issues we see with Kenmore refrigerators like model 10657026602 are cooling problems, ice maker and water dispenser troubles, water leaks, frost buildup, and unusual noises. Many of these come down to airflow restrictions, dirty condenser coils, door seal leaks, or a failing water supply component (valve, filter, or ice maker). For model-specific troubleshooting steps, use the owner's manual.

Common problems and what to check first

• Not cooling or warm temperatures: confirm controls are on, doors fully close, vents are not blocked, and allow 24 hours after a new install or major setting change for temperatures to stabilize.
• Runs too much: frequent door openings, warm room temperature, or a large food load can make the compressor run longer.
• Noisy operation: buzzing, gurgling, popping, and cracking can be normal; buzzing often happens when the water valve opens to fill the ice maker.
• Ice maker not making ice: verify the shutoff arm or switch is on, freezer is cold enough, and water supply is connected.
• Water dispenser slow or tastes off: replace the filter and flush the first few glasses.
• Leaks or puddles: check the water line connections, inlet valve, and defrost drain area.

Quick symptom-to-likely-cause guide

Symptom	Common cause	Good next step
Fresh food warm, freezer OK	Airflow issue or evaporator fan problem	Check vents; listen for fan; inspect frost pattern
No ice and no water	Water supply off or inlet valve issue	Confirm supply valve open; test fill at valve
Slow water flow	Clogged filter	Replace genuine Kenmore refrigerator water filter EDR3RXD1
Frost buildup	Door not sealing or defrost issue	Inspect gaskets; check defrost heater/thermostat
Clicking/buzzing near back	Water valve energizing or compressor start components	Identify when noise occurs (ice fill vs. start)

Parts that commonly solve these problems (when diagnosis points there)

• Water flow and ice fill issues: refrigerator inlet valve W10408179
• Ice production failures: refrigerator ice maker 2198597
• Poor water taste or low flow: genuine Kenmore refrigerator water filter EDR3RXD1
• Frost and defrost complaints: refrigerator heater WP2323198 and refrigerator defrost bi-metal thermostat WPW10225581
• Warm temps with weak airflow: refrigerator evaporator fan motor WP2315549

Why it matters

Catching the root cause early protects food temperatures, reduces energy use, and prevents secondary damage like ice buildup, water leaks, or compressor overwork.

For model-family diagnostics that often apply to Kenmore 106 refrigerators, we also use the Kenmore 106 model refrigerator error codes guide.

Last updated: February 2026