Kenmore 11029832800 washer Parts

Your Kenmore washer model number is printed on the appliance’s model and serial tag. For Kenmore washers, it’s commonly under the lid on top-load models or inside the door opening on front-load models; once you find it (for example, 11029832800), we can match the correct parts and diagrams for your exact washer.

Where to look on Kenmore washers

Check these common tag locations first:

• Top-load washer: under the lid, around the tub opening
• Front-load washer: inside the door opening, along the door frame
• Back panel: near the power cord entry or rear cabinet
• Control console area: behind or under the console on some designs
• Side of the cabinet: near the bottom edge on some models

What the model number looks like

Kenmore washer model numbers often start with 110 and run 10 to 12 digits (sometimes longer). Write the number exactly as shown, including any leading zeros.

What you see	What it means	Why it matters
11029832800	Full model number	Ensures exact-fit parts for your washer
Serial number	Production identifier	Helps with age and service history, not parts fit
Partial number (first 3 to 6 digits)	Model prefix only	Not enough to guarantee correct parts

Tips to avoid ordering the wrong part

• Copy the model number directly from the tag, not from the control panel labels
• If the tag is worn, use a flashlight and take a close-up photo
• Match the model number on your tag to the model shown in the 11029832800 owner’s manual
• Use the model number when selecting common repair parts like the washer lid switch assembly WP8318084

Why it matters

Kenmore produced many washer designs that look similar but use different drive systems, timers, and switches. Using the exact model number (like 11029832800) prevents fit issues and repeat repairs.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore 11029832800 top-load washer, correct installation, avoiding overloads, and basic care help it reach the longer end of that range; worn drive and drain components are the most common life-shorteners.

Typical lifespan and what affects it

Most washers fall into a predictable window, and usage and setup make the biggest difference.

• Loads per week: more cycles equals faster wear on the drive system
• Overloading: strains the motor, coupling, clutch, and gear case
• Out-of-level installation: increases vibration and can accelerate suspension and tub wear
• Water quality: sediment can shorten inlet valve life
• Cold-weather storage: freezing conditions can damage internal water passages

Quick care checklist (high impact)

Use these habits to extend service life on the 11029832800.

• Keep the washer level on a sturdy floor (reduces “walk” and noise)
• Use the right detergent amount; too much can leave residue and stress draining
• Do not store or operate the washer at or below 32°F
• Periodically inspect fill hoses and connections for seepage
• If agitation gets weak, address it early (small parts can prevent bigger failures)

Common wear items on this model

These parts often show symptoms before the washer reaches end-of-life.

Symptom	Commonly involved part	What you’ll notice
Won’t spin or agitates poorly	Coupling 285753A	Motor runs but basket movement is weak or stops
Won’t drain	Washer drain pump WP3363394	Water left in tub, slow drain, humming
Won’t start or stops when lid opens/closes	Washer lid switch assembly WP8318084	No spin/agitate with lid closed

Why it matters

Knowing the 10 to 15 year average helps you decide whether to repair or replace. If your washer is near that age and needs a major drive repair (gear case, clutch, or motor), comparing repair cost to remaining expected life keeps the decision practical.

For model-specific operating and care guidance, follow the maintenance and use steps in the 11029832800 owner’s manual.

Last updated: February 2026

For the Kenmore 11029832800 washer, the most commonly replaced parts are the lid switch, drain pump, motor coupling, agitator dogs, and water inlet valve. These parts directly affect filling, agitating, draining, and spinning, so they are frequent fixes for “won’t start,” “won’t drain,” or “won’t agitate” symptoms.

Commonly replaced parts for this model

These are the parts we see replaced most often on direct-drive Kenmore top-load washers like model 11029832800:

• Washer lid switch assembly WP8318084: stops spin/agitate when the lid is open; common “won’t spin” cause
• Washer drain pump WP3363394: fixes no-drain, slow drain, or water left in tub
• Coupling 285753A: connects motor to transmission; common for “motor runs but won’t agitate/spin”
• Agitator dog 80040: restores upper agitator movement; common for poor wash action
• Washer water inlet valve WPW10175893: fixes no-fill, slow fill, or hot/cold fill problems
• Clutch 285785: helps basket reach full spin; common for weak spin or burning smell

Quick symptom-to-part guide

Symptom	Most likely part(s) to check	What you may notice
Won’t spin or start	Lid switch assembly	No motor action when lid closes
Won’t drain	Drain pump, pump hose	Humming, standing water
Won’t agitate	Coupling, agitator dogs	Tub fills but clothes barely move
Slow or no fill	Water inlet valve	Long fill times, wrong temp
Weak spin	Clutch, suspension spring	Clothes wetter than normal

Why these parts matter

These components are “high-use” items. The lid switch is a safety interlock, the pump handles every drain, the coupling absorbs shock between the motor and gearcase, and the agitator dogs wear as the agitator reverses during wash.

Before you order

We recommend these checks first so you buy the right fix:

• Unplug the washer before inspecting any internal parts.
• Confirm the symptom happens on more than one cycle.
• Look for simple causes (kinked drain hose, overloaded tub, unbalanced load).
• Use the troubleshooting and disassembly steps in the installation guide to plan tools and access.

Last updated: March 2026