Kenmore 66513203N412 dishwasher Parts

Yes. We still support replacement parts for many Kenmore dishwashers, including Kenmore model 66513203N412, as long as the specific part is still manufactured and available. The key is matching parts by your full model number, then choosing the correct component for the symptom (drain, fill, heating, racks, or controls).

How to make sure you get the right part

Use the complete model number 66513203N412 and confirm the part’s location and function in the diagrams and instructions in the 66513203N412 owner's manual.

• Match the model number exactly (including all digits and letters)
• Identify the symptom first (won’t drain, won’t fill, not drying, poor cleaning)
• Compare the part name and ID, not just a look-alike photo
• Replace worn rack hardware early to prevent rack damage
• After any repair, run a short cycle and confirm water enters the tub

Common Kenmore dishwasher parts people replace

These are frequently replaced items for this model family:

Problem you see	Part that often fixes it	Example part for 66513203N412
Upper rack won’t stay up or rolls poorly	Rack adjuster/roller hardware	Dishwasher rack adjuster W10712395
Dishwasher won’t drain	Drain pump or drain hose	Dishwasher drain pump (model-specific)
Dishwasher won’t fill or fills slowly	Water inlet valve	Dishwasher water inlet valve (model-specific)
Dishes not drying well	Heating circuit components	Heating element assembly (model-specific)

Why it matters

Kenmore dishwashers are built to be serviceable for years, and many repairs are straightforward when you match parts to the exact model. Using the correct part helps restore proper washing, draining, and drying performance and prevents repeat failures.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66513203N412 is usually worth it when the problem is a common wear item (rack hardware, drain hose, inlet valve) and the repair cost is reasonable; it is less worthwhile when major components (control, tub, motor) fail and the total cost approaches replacement.

Quick way we decide: cost, age, and the failed part

• If the dishwasher is under ~10 years old, repairs are typically a good value.
• If the repair is under ~50% of replacement cost, repairing usually makes sense.
• If the failure is a “big ticket” part (tub, control, sump motor), compare total repair cost to a new unit.
• If performance issues are maintenance-related, cleaning and setup often restore results without major parts.

Common repairs that are usually worth it on 66513203N412

These are frequent, straightforward fixes that often restore normal washing and draining:

• Upper rack problems: dishwasher rack adjuster W10712395
• Not filling or filling slowly: dishwasher water inlet valve W11175771
• Not draining: dishwasher drain pump W10876537
• Leaks at the pump area: dishwasher pump grommet WPW10538166
• Poor wash coverage from below: dishwasher spray arm, lower W10849471

Repairs that often push toward replacement

Issue	Typical impact	Usual decision driver
Control/console problems	Can stop cycles or cause erratic operation	Higher part cost plus labor
Tub damage or major leaks	Structural, hard to justify	High part cost
Sump motor assembly failure	Wash performance and noise	Expensive assembly

Why it matters

A dishwasher repair is most cost-effective when it restores core functions (fill, wash, heat, drain) with a single part. Your 66513203N412 also has features like a heating element and filtration that benefit from routine care, which can prevent repeat problems.

What we recommend before spending money

• Check the troubleshooting section in the 66513203N412 owner’s manual
• Confirm the symptom (no fill, no drain, poor cleaning, won’t start)
• Inspect and clean filters and spray arms
• If you see an error code, use Kenmore 665 model dishwasher error codes

Last updated: February 2026

The model number for your Kenmore dishwasher is printed on the appliance’s rating label; on 66513203N412 units, it’s typically on the tub frame where the door closes. Open the door fully and look around the inner door edge and tub opening for a sticker or metal tag.

Where to look on a Kenmore 66513203N412 dishwasher

Check these common label locations first:

• Along the left or right side of the tub opening (vertical frame)
• On the top edge of the tub opening (under the counter lip)
• On the inner edge of the door itself (near the latch area)
• Near the bottom edge of the tub opening (front frame)
• On the side wall just inside the tub (less common)

If you see multiple numbers, the model number is the one that matches the 665.xxxx format (for example, 665.1320xx). For diagrams and identification notes, use the owner's manual.

Tips to read the label correctly

Dishwasher labels can be hard to read due to steam and detergent residue. We recommend:

• Wipe the label gently with a damp cloth and mild soap
• Use a flashlight and view from an angle to reduce glare
• Take a photo and zoom in to read small characters
• Write down the full model number and the serial number

Why the exact model number matters

Kenmore 665-series dishwashers can use different racks, pumps, and controls depending on the exact suffix. The full model number helps ensure the correct fit for parts like a dishwasher rack adjuster W10712395 or a dishwasher water inlet valve W11175771.

What you’re looking for	Example format	Why it’s needed
Model number	665.1320XX	Matches parts diagrams and correct replacements
Serial number	Letters and numbers	Helps identify production range for some parts

Last updated: March 2026