Kenmore 10659592992 side-by-side refrigerator Parts

The most common issues we see with the Kenmore 10659592992 side-by-side refrigerator involve ice maker and water dispensing problems, warm temperatures from airflow or defrost faults, and door sealing or closing issues. Your 10659592992 owner's manual helps confirm control settings and basic checks before replacing parts.

Most common symptoms (and what usually causes them)

• No ice or small/hollow cubes: water supply restriction, inlet valve not opening fully, ice maker failure
• Water dispenser not working or slow: inlet valve issue, frozen/kinked water tube, filter housing restriction
• Refrigerator or freezer too warm: evaporator fan airflow problem, diffuser issue, defrost system fault
• Frost buildup on back wall: defrost heater or defrost bi-metal not working
• Doors not closing well or leaking air: worn door gasket, door cam wear, bins/shelves misaligned

Quick checks we recommend first

1. Verify temperature settings and allow 24 hours after changes.
2. Confirm the condenser area is clean and the unit has proper airflow clearance.
3. For ice and water: make sure the shutoff valve is fully open and the supply line is not kinked.
4. Check for frost on the freezer back panel; heavy frost points to a defrost problem.
5. Inspect door gaskets for gaps, tears, or hardened sections.

Parts that commonly fix these problems

Symptom	Common part to check/replace	What it does
No ice or slow fill	Refrigerator inlet valve W10408179	Opens to send water to ice maker and dispenser
No ice (mechanical failure)	Ice maker assembly 4317943	Cycles to harvest and refill ice
Frost buildup, warm temps	Refrigerator heater WP2323198	Melts frost off the evaporator
Frost buildup, defrost not cycling	Refrigerator defrost bi-metal WPW10225581	Senses coil temperature for defrost control
Door not closing, air leaks	Refrigerator door cam (black) WP2182179	Helps the door lift/close smoothly

Why it matters

Ice, water, and temperature complaints often share the same root causes: restricted water flow, poor airflow, or a failed defrost component. Fixing the underlying cause protects food temperatures and prevents repeat icing and frost issues.

Last updated: March 2026

The cubic-foot capacity for Kenmore side-by-side refrigerator model 10659592992 is listed in the specifications section of the product documentation; use the 10659592992 owner's manual to get the exact total volume for your specific configuration (ice maker, shelves, and bins).

Where to find the exact cubic feet

Capacity is typically shown as “total capacity” (combined fresh food + freezer) in the specs.

• Check the “Product specifications” or “Refrigerator specifications” pages in the manual
• Look for a line labeled “Total capacity” or “Total volume” (cu. ft.)
• If your unit has an ice maker installed, note that usable space changes but the rated capacity stays the same
• If you are comparing models, use total capacity for apples-to-apples comparisons

Typical capacity range for this style

Most Kenmore 106-series side-by-side refrigerators fall into a common size band; your exact number depends on the specific build.

Refrigerator type	Typical total capacity range
Side-by-side (standard width)	20 to 26 cu. ft.

Why it matters

Knowing the cubic feet helps when comparing refrigerator sizes, planning food storage, and understanding why features like an in-door ice system can reduce usable freezer room.

Last updated: January 2026

Most Kenmore side-by-side refrigerators, including model 10659592992, do not have a single dedicated “reset” button. The practical reset is a power reset (unplugging briefly) and then resetting the temperature controls to your normal settings; see the steps in the 10659592992 owner's manual.

How to “reset” the refrigerator (safe, standard method)

• Turn the temperature control(s) to OFF.
• Unplug the refrigerator from the wall outlet (do not use an extension cord).
• Wait 2 to 5 minutes.
• Plug the refrigerator back in.
• Set the control(s) back to the desired temperature setting.
• Allow 24 hours for temperatures to stabilize after changes.

If you are trying to reset the ice maker

If the issue is “no ice,” the fix is usually not a reset button; it is an ON/OFF condition or water supply issue.

• Confirm the shut-off arm is down (ON) if your model uses a wire arm.
• If your model has an ice maker switch, set it to ON.
• Make sure the household water shut-off valve is fully open.
• Check for a jammed cube in the ejector area (use a plastic utensil).
• After restoring water or turning the ice maker on, wait 24 hours for normal production.

Helpful part checks (when symptoms point to a failure):

• Ice maker assembly - refrigerator ice maker by whirlpool 4317943 (no ice, not cycling)
• Refrigerator inlet valve W10408179 (no water to ice maker or dispenser)

Quick guide: what “reset” means on this model

What you want to reset	What to do	What to expect
Cooling controls	Power reset + set controls back	Temps stabilize in ~24 hours
Ice maker	Verify ON position + water supply	Ice in ~24 hours after correction
Dispenser behavior	Power reset; then check for ice/water blockage	Immediate change if it was a control glitch

Why it matters

A power reset clears minor control glitches, but most “needs a reset” complaints on a side-by-side refrigerator are caused by settings, door sealing, airflow restrictions, or water supply problems, not a hidden button.

Last updated: January 2026