Kenmore 10653293201 refrigerator Parts

The most common problems we see on Kenmore refrigerators like model 10653293201 are cooling issues (too warm or not cooling), ice maker not making enough ice, water dispenser or leak problems, excess frost or moisture buildup, and unusual noises. Many of these trace back to airflow, door sealing, or water supply setup; use the owner's manual troubleshooting steps first.

• Not cooling or temperature too warm: make sure air vents are not blocked, and minimize frequent door openings.
• Ice maker not producing ice or not enough ice: after installation, allow 72 hours for full ice production; confirm freezer temperature is cold enough.
• Refrigerator will not operate: verify the power cord is plugged into a grounded 3-prong outlet; reset a tripped breaker or replace a blown fuse.
• Moisture buildup inside: reduce door openings, confirm food is wrapped, and keep vents clear.
• Noisy operation: many sounds are normal; high-efficiency models can run longer than older units.

If troubleshooting points to a failed component, these are common replacements for this model:

• Water quality or slow dispensing: refrigerator water filter EDR5RXD1
• Water leaks or no water to dispenser/ice maker: refrigerator inlet valve W10822681
• Frost buildup or defrost problems: refrigerator defrost bi-metal WPW10225581
• Warm temps from poor airflow: refrigerator air diffuser WP2216112

Cooling, ice, and leak complaints often start as simple issues (blocked vents, doors opened often, or a new ice maker needing time). Catching those early helps protect food, reduces frost and moisture, and prevents unnecessary part replacement.

Last updated: February 2026

A Kenmore side-by-side refrigerator like model 10653293201 usually stops cooling because power is interrupted, the controls are set to OFF or need a reset, airflow is blocked by items in front of vents, or the doors are not sealing. Start with the quick checks in the owner's manual.

• Confirm the power cord is fully plugged into a grounded 3-prong outlet.
• Check your home breaker or fuse; reset or replace if tripped.
• Make sure the refrigerator and freezer controls are not set to OFF.
• If your model has digital controls, turn the unit OFF then ON to reset.
• Look for blocked air vents in either compartment; move food packages away from vent openings.
• Check door gaskets for gaps all the way around; reseat shelves/bins that prevent full closure.

Blocked vents and frequent door openings can make the refrigerator seem like it is not cooling because cold air cannot circulate from the freezer to the fresh food section.

When airflow is restricted or doors do not seal, the compressor has to run longer and temperatures drift upward. Fixing vent blockage and door sealing prevents food spoilage and reduces strain on the cooling system.

These parts are not the first step, but they are commonly related to “not cooling” complaints after you complete the checks above:

• Refrigerator air diffuser WP2216112 (controls cold-air flow into the refrigerator section)
• Refrigerator defrost bi-metal WPW10225581 (can contribute to frost buildup that blocks airflow)
• Refrigerator condenser fan W10181323 (helps remove heat; issues can reduce cooling)

Last updated: February 2026

On Kenmore model 10653293201, “error 15” is most often reported as an ice maker related fault (commonly shown on some Kenmore designs as Er IS or Er 15, meaning an ice maker sensor signal problem). Use the troubleshooting and control reset steps in the owner's manual to match the exact display and correct the cause.

• Write down the exact characters on the display (for example: 15, Er, Er IS).
• Note what is failing: ice maker, dispenser, cooling, or just an alarm.
• Check whether the freezer is holding proper ice-making temperature.
• Look for obvious ice jams in the door chute or ice bucket.
• If the unit has digital controls, perform a control reset (OFF then ON) as described in the manual.

On Kenmore refrigerators that use this code format, Er IS (sometimes read as Er 15) indicates the control is not receiving the expected input from the in-door ice maker sensor. Common causes include a sensor issue, a loose connection, or a control problem.

Follow the sequence below; it prevents replacing parts before basics are verified.

If you have no water to the ice maker or dispenser along with the code, the water supply components are the first place we look.

• Refrigerator inlet valve W10822681 (water supply to ice maker and dispenser)
• Refrigerator water filter EDR5RXD1 (a clogged filter can restrict flow)
• Refrigerator water filter housing WP2186443 (leaks or poor filter seating)

An ice maker sensor or water supply problem can stop ice production, cause intermittent dispensing, and trigger repeated error displays. Matching the exact code format to the troubleshooting steps avoids unnecessary part replacement.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10653293201, the model number is printed on the model and serial number label located on the inside wall of the refrigerator compartment. Use that label to record the full model and serial number for parts lookup and service reference (see the owner's manual).

• Open the fresh food (refrigerator) door, not the freezer door
• Look along the inside side walls of the refrigerator compartment
• Check near the crisper area and lower side wall first (common placement)
• Use a flashlight; the label can be small and easy to miss
• Write down both the model number and serial number exactly as shown

We recommend recording these items exactly as printed:

• Model number (for this unit: 10653293201)
• Serial number
• Purchase date (if you still have it)

Kenmore refrigerators often have similar-looking doors, shelves, and water system parts across multiple models. Using the exact model number from the inside label helps ensure you get the right replacement parts the first time.

Last updated: February 2026