Kenmore Elite 10654789801 side-by-side refrigerator Parts

We size Kenmore Elite model 10654789801 by its rated storage capacity, which is typically listed on the model’s product data label and in the 10654789801 owner's manual. Use that capacity number (in cubic feet) when comparing refrigerators, choosing replacement shelves/bins, or planning kitchen space.

How to find the exact cubic feet for model 10654789801

Check these common places first:

• The product data label inside the fresh food compartment (often on a side wall)
• The owner’s manual specifications section
• The model and serial tag area near the crisper drawers or door frame
• Any energy or product information label that lists capacity

Why the number you see online may not match your refrigerator

Capacity listings can vary depending on how a retailer reports it (total vs. usable space) or which closely related model they’re referencing.

Capacity type	What it means	What to use it for
Total (rated) capacity	Manufacturer’s published cubic feet	Comparing models, general sizing
Usable capacity	Space after shelves, bins, ice maker, etc.	Real-world storage planning

Quick checks that help confirm you have the right model

Before relying on any capacity figure, match the model number exactly:

• Confirm the model reads 10654789801 (all digits, no extra characters)
• Verify the unit is a Kenmore Elite side-by-side refrigerator
• Note whether you have an ice maker and water dispenser, since they reduce usable space

Why it matters

Using the correct cubic feet rating helps you compare like-for-like refrigerators and avoid ordering storage parts (door bins, shelves, drawers) based on a similar looking but different capacity model.

Last updated: January 2026

For Kenmore Elite model 10654789801, the correct base-grille water filter is Part #9030, which matches the replacement filter EDR3RXD1. Use your refrigerator’s full model number to confirm the exact filter style and to follow the correct replacement and reset steps in the 10654789801 owner's manual.

Quick way to identify the right filter

• Find the model number tag inside the fresh food compartment (often on a side wall or ceiling) and confirm it reads 10654789801.
• Check where the filter installs; this model uses a base grille filter below the freezer door.
• Match the filter identifier from the manual: Replacement Filter: Part #9030.
• Order the model-matched cartridge: genuine Kenmore refrigerator water filter EDR3RXD1.
• Keep the existing filter cap; it transfers to the new cartridge.

Replace, flush, and reset (what to expect)

When you change the filter on model 10654789801, some water in the old cartridge is normal and a small spill can happen.

After installing the new filter:

• Flush at the dispenser in 5-seconds-on, 5-seconds-off cycles until water flows.
• Continue flushing for about 5 minutes after water starts flowing.
• Reset the filter status by pressing and holding the FILTER button for 3 seconds (light changes from Replace/red to New/Good/green).

Common “wrong filter” symptoms

Symptom	Most common cause	What to do next
Filter will not seat/lock	Wrong filter style or cap not aligned	Recheck Part #9030 style; align cap ridge to arrow
Low water flow	Air in lines or clogged filter	Flush for 5 minutes; replace if overdue
Leaking at filter area	O-ring cover left on or cap not fully snapped	Remove covers from O-rings; reinstall and tug-check

Why it matters

Using the correct filter for Kenmore Elite 10654789801 prevents leaks, protects the water inlet valve and dispenser flow, and ensures the filter status light resets correctly so you know when service is due.

Last updated: January 2026

Most Kenmore Elite refrigerators, including model 10654789801, typically last 10 to 15 years with normal household use. Regular maintenance (especially cleaning condenser coils and keeping door seals tight) is what most often separates a 10-year refrigerator from a 15-year one; major sealed-system repairs can shorten practical life.

Typical lifespan and what affects it

A refrigerator’s lifespan is mostly driven by compressor run time, airflow, and how hard the sealed system has to work to hold temperature.

• Maintenance habits: cleaning coils, replacing filters, keeping vents clear
• Environment: hot garages, tight built-ins, dusty homes, pet hair
• Usage patterns: frequent door openings, overpacking, warm food loads
• Water and ice system care: timely filter changes, leak prevention
• Repair economics: high-cost repairs (compressor, evaporator, control) often drive replacement decisions

Maintenance checklist to help your 10654789801 reach the high end of the range

We recommend using the care and cleaning schedule in the 10654789801 owner's manual.

• Vacuum and brush condenser coils regularly (more often with pets)
• Confirm door gaskets seal all the way around (no gaps, no tearing)
• Keep air vents inside both compartments unblocked
• Replace the water filter on schedule to protect water flow and ice maker performance
• After a move or new install, allow about 24 hours for temperatures and water supply to stabilize

Common “end-of-life” symptoms and what they usually point to

Symptom	Often related to	What to check first
Warm refrigerator or freezer	Sealed system, airflow, controls	Coil cleaning, fan operation, temperature settings
Loud humming or repeated clicking	Compressor start components or compressor	Listen at rear, check for overheating and dust buildup
Frost buildup, poor cooling	Defrost system	Defrost heater and thermostat function
Slow water dispensing or small ice	Filter or inlet valve	Filter age, water pressure, valve performance

If you are maintaining water and ice performance, the correct replacement filter for this model family is commonly listed as genuine Kenmore refrigerator water filter EDR3RXD1.

Why it matters

A refrigerator that is running hot, restricted by dirty coils, or leaking cold air through worn gaskets runs longer cycles. That extra workload accelerates wear on the compressor and other key components, which is the main reason lifespan drops below the 10 to 15 year average.

Last updated: January 2026

Yes. For Kenmore Elite refrigerator model 10654789801, the most reliable reset is a power reset: turn the temperature control(s) to OFF if your control has an OFF position, unplug the refrigerator for 5 minutes, then restore power and set your normal temperatures. Use the 10654789801 owner's manual for the exact control locations.

Quick reset options

• Power reset (best first step): unplug for 5 minutes, then plug back in.
• Control reset: after power returns, re-set refrigerator and freezer temperatures.
• Dispenser motor reset: if ice stops after holding the dispenser lever too long, wait 3 minutes and try again.
• After reset: confirm doors close fully and interior vents are not blocked.

Step-by-step: power reset

1. Turn the temperature control(s) to OFF (if available).
2. Unplug the refrigerator (or switch off the dedicated breaker).
3. Wait 5 minutes.
4. Restore power.
5. Set controls to your preferred settings.
6. Allow 24 hours for temperatures to stabilize.

If the issue is water or ice, check these basics

• Water shutoff valve fully open
• Home water pressure 30 psi or higher
• No kinked or pinched water line
• Flush the system after a new filter or new installation

Symptom	What to do	What it points to
Display glitches or odd behavior	Do the 5-minute power reset	Electronic control logic
Ice stops after long dispense	Wait 3 minutes	Dispenser motor protection
Weak water flow	Verify 30 psi, valve open, line straight	Water supply issue

Why it matters

A reset clears temporary control glitches, but it will not fix ongoing problems like low water pressure, a kinked supply line, or a failing component.

Last updated: January 2026