Kenmore Elite 79048023801 wall oven Parts

On Kenmore model 79048023801, the model and serial number are printed on the serial plate located along the interior side trim of the oven; you can see it when you open the oven door. This is the number we use to match the correct wall oven parts and diagrams.

Where to look (fast checklist)

• Open the oven door fully.
• Look along the left or right interior side trim (the vertical trim beside the oven cavity).
• Find the serial plate label; it lists model and serial numbers.
• Write down the full model number and serial number.
• If you are ordering parts, also note any lot number/letter shown on the plate.

What the serial plate label looks like

Most labels include:

• Model number (for example, 79048023801)
• Serial number
• Electrical ratings (volts/amps)
• Manufacturing or lot code

Why it matters

Using the exact model number helps us pull the right Kenmore Elite wall oven parts list, including common replacements like the range oven light bulb 316538904 or the frigidaire range oven temperature sensor 316217002. Even small model-number differences can change the correct bake element, control panel, or wiring harness.

Quick reference table

What you need	Where to find it	When you need it
Model number	Serial plate on interior side trim (door open)	Parts lookup, diagrams, manuals
Serial number	Same serial plate	Service history, part compatibility checks
Lot number/letter	Same serial plate (if shown)	Parts inquiries and matching revisions

For a visual and additional details, check the owner's manual.

Last updated: February 2026

If your Kenmore Elite wall oven model 79048023801 is not working at all, the most common causes are a power interruption (clock not set yet), a tripped breaker or blown fuse, or control settings that are not programmed correctly. Start with the power supply and control reset steps in the owner's manual.

Quick checks (fastest fixes first)

• Set the clock if the display is flashing after a power interruption; the oven will not program until the clock is set.
• Verify the circuit breaker is fully engaged (turn it OFF, then back ON firmly).
• Check the home fuse (if applicable) and replace or fully seat it.
• Press STOP/CLEAR to clear beeping or a fault condition, then reprogram the oven.
• If you see F11 (or another fault code), write it down after clearing it; it helps pinpoint the failure.
• If the oven light is out, check for a loose or burned-out bulb.

What the symptoms usually mean

Symptom	Most likely cause	What to do next
Display flashing, oven will not start	Power was interrupted; clock not set	Set the clock, then try Bake again
Completely dead (no display)	Power supply issue	Check breaker, fuse, and junction box connection
Beeping with fault code (example: F11)	Electronic control detected a fault	Clear with STOP/CLEAR; reprogram; record code if it returns
Oven light does not work	Bulb burned out or loose	Replace or tighten the bulb

Parts that commonly fix “not working” complaints

If power and settings check out, a failed component can stop heating or cause erratic operation. These are common service parts for this model:

• Frigidaire range oven temperature sensor 316217002 (temperature feedback to the control)
• Frigidaire range bake element 318254902 (primary heat source for Bake)
• Terminal block 5304409888 (power connection point; damage here can cause loss of power)
• Range oven light bulb 316538904 (if the only issue is the light)

Why it matters

Wall ovens use 240V power and electronic controls; a simple power interruption can lock out programming until the clock is set, while repeated fault codes (like F11) point to a control or wiring issue that should be addressed before it worsens.

Last updated: February 2026

If your Kenmore Elite wall oven model 79048023801 fan is not spinning, the most common causes are normal fan behavior (it stops when the door opens in convection), a seized fan blade, a failed fan motor, or a wiring/control issue. Use the installation guide and owner's manual to confirm when the fan should run.

First, confirm the fan is supposed to be running

On this model, the convection fan runs during convection baking/roasting and stops when you open the oven door. Also, the cooling fan can cycle on and off and may run after the oven is turned off.

Quick checks

• Set Convection bake and watch for the convection fan indicator on the display (rotating fan icon).
• Keep the door closed; the convection fan can stop with the door open.
• Let the oven heat up; some fans start after internal temperatures rise.
• If you only hear airflow sometimes, that can be normal cooling-fan cycling.

What to check if the fan never spins

Turn off power at the breaker before inspecting anything inside the oven.

• Obstruction: Look for foil, a loose screw, or debris contacting the blade.
• Fan blade damage: A bent blade can bind and prevent startup.
• Motor failure: A humming motor with no rotation often indicates a weak or seized motor.
• Wiring/connectors: Heat can loosen or damage connectors, especially near the rear.
• Control issue: If the oven is not actually in a convection mode, the fan may not be commanded on.

If you find a damaged blade, the fan blade 318398302 is the correct replacement part listed for this model.

Symptom-to-cause guide

What you notice	Most likely cause	What we recommend
Fan stops when door opens	Normal convection behavior	Test with door closed in convection mode
Fan runs after oven is off	Normal cooling fan operation	Let it finish cooling; verify vents are clear
Hums but will not spin	Seized motor or binding blade	Check blade for rubbing; inspect motor
No sound, no airflow in convection	No power to motor, wiring, or control	Check connections; verify mode/settings

Why it matters

A working convection or cooling fan helps keep temperatures even and protects electronic components from overheating. If the fan is stuck, you can see uneven baking, longer preheat times, or heat-related shutdowns.

Last updated: February 2026