Kenmore 11067102310 electric dryer Parts

A bad heating element in your Kenmore electric dryer model 11067102310 usually shows up as no heat while the drum still tumbles. We confirm it by checking the element with a multimeter for continuity; a good element typically measures about 10 to 50 ohms.

Quick checks first (before testing parts)

• Run a timed cycle on high heat for 5 minutes, then open the door and feel for heat (use caution).
• Check both household fuses or breakers; many electric dryers use two.
• Confirm the dryer has a 240-volt supply (the motor can run on 120V, but heat needs 240V).
• Make sure the vent is not crushed or kinked; poor airflow can cause overheating and shutdowns.
• Review the heat and power checks in the 11067102310 installation guide.

How we test the heating element (multimeter)

1. Unplug the dryer (or switch off both breakers).
2. Access the heater terminals (location varies by design; follow the 11067102310 owner's manual).
3. Set the meter to resistance (ohms) and measure across the element terminals.
4. Interpret the reading:
   • 10 to 50 ohms: element is typically OK
   • OL / infinite / no continuity: element is failed and should be replaced

What else can mimic a “bad element”

Symptom	More likely cause	Common related part
Tumbles, no heat	Tripped breaker or blown fuse	Home electrical supply
Heats briefly, then stops	Overheat condition from airflow restriction	Venting, lint buildup
No heat, cycles act odd	Temperature sensing issue	Dryer thermistor WP8577274
No heat after overheating event	Safety device opened	Dryer thermal cut-off fuse kit 279973

Why it matters

A failed element stops drying completely, but airflow problems and overheating can also take out safety fuses and shorten the life of the heater. Fixing the root cause (power and venting) helps the new part last.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the appliance’s ID label (model and serial tag). On Kenmore model 11067102310, you’ll typically find that label inside the door opening, on the door frame, or on the back panel; match the full number exactly to get the right parts and instructions.

Where to look for the model number label

Check these common spots first:

• Inside the dryer door opening on the door frame
• On the back panel of the dryer cabinet
• Around the lint screen housing area (depending on door style)
• On the lower front area behind the toe panel (some designs)

What to write down (and why)

Record both the model and serial number exactly as shown. The model number identifies the design family; the serial number helps narrow production details when parts changed during a run.

What you see on the label	Example	Why it matters
Model number	11067102310	Ensures correct part fit and diagrams
Serial number	(varies)	Helps confirm version-specific parts
Electrical info	Volts/amps	Helps with safe installation and wiring

Tips to avoid ordering the wrong part

Use these quick checks before you buy a heating element, door switch, or drum support parts:

• Match every digit of 11067102310 (no missing or swapped numbers)
• Use the model number when selecting parts like the dryer heating element WP3387747
• If your dryer won’t start, confirm the model before replacing items like the dryer door switch WP3406107
• Keep a photo of the label on your phone for future reference

Why it matters

Kenmore dryers share similar styling across many series, but internal components (like the heating circuit, wire harness, and drum support system) can differ by model. Using the exact model number keeps troubleshooting and part selection accurate.

For additional identification and setup details, use the 11067102310 installation guide.

Last updated: February 2026

To hard reset your Kenmore electric dryer model 11067102310, disconnect power long enough for the control to fully power down, then restore power and try a cycle again. This clears many temporary control glitches without replacing parts.

Hard reset steps (safe and effective)

• Turn the dryer OFF.
• Unplug the dryer from the outlet; for a direct-wired setup, turn OFF the breaker.
• Wait 1 to 5 minutes.
• Restore power.
• Press and hold START/PAUSE until you hear the dryer engage and the drum begins moving.
• Run a short timed cycle to confirm normal operation.

If the dryer still will not start after a reset

These checks match common “won’t run” causes for this Kenmore dryer:

• Confirm the door is fully closed; a failed door switch can prevent starting.
• Check the home electrical supply; electric dryers typically need two fuses/breakers.
• Verify you have a proper 240-volt supply (drum may turn with no heat if one leg is out).
• Make sure you are pressing and holding START/PAUSE long enough.
• If the drum turns but there is no heat, check the same power-supply items first.

Symptom after reset	Most likely area to check	What to do next
No lights, no response	Power supply	Check breaker/fuses, outlet, cord connection
Lights on, will not start	Door/controls	Confirm door closes firmly; test door switch
Runs but no heat	Power supply, heating circuit	Check both breakers/fuses; then heating components

Why it matters

A hard reset is the fastest way to clear a stuck control state. If the problem comes right back, the reset helps narrow the issue to power supply, door switch, or a failing component rather than a one-time glitch.

Helpful references for this model

• Use the safety and power-disconnect steps in the 11067102310 owner's manual.
• If you suspect the door is not being detected as closed, the dryer door switch WP3406107 is the common interlock that prevents the dryer from running.

Last updated: February 2026

The Kenmore electric dryer model 11067102310 is a standard 27-inch-wide dryer. Based on the installation dimensions, it measures about 43 inches tall, 27 inches wide, and 29 1/2 inches deep (depth can increase if you include the vent elbow clearance). See the exact diagram in the installation guide.

Model 11067102310 dimensions (installation)

These are the cabinet dimensions shown for installation planning:

• Width: 27 in (686 mm)
• Height: 43 in (1092 mm)
• Depth: 29 1/2 in (749 mm)
• Recommended rear clearance for vent elbow (most installs): 5 1/2 in (140 mm)

Measurement	Dryer cabinet	What can add space
Width	27 in	Side clearance (recommended 1 in each side in many installs)
Height	43 in	None (cabinet height)
Depth	29 1/2 in	Exhaust vent elbow and ducting behind dryer

Why your measured depth may not match

If you measure a different depth at home, it is usually because of installation details, not the dryer itself.

• Vent elbow sticks out behind the cabinet
• Flexible venting bows outward
• Wall outlet box or recessed vent box changes how close the dryer sits
• Baseboard or trim prevents the cabinet from sitting flush
• Closet installs often need extra space for airflow and service access

Quick fit-check tips before you buy parts or move the dryer

• Measure the space opening (width and height) and compare to the cabinet size.
• Plan for rear vent clearance so the vent does not crush.
• If installing in a closet, allow for door swing and required ventilation openings.
• Confirm your vent uses 4-inch diameter ducting.

For operating and care details (including airflow and venting tips that affect drying performance), use the 11067102310 owner’s manual.

Last updated: February 2026