Kenmore 11092573100 washer Parts

To unclog the drain hose on your Kenmore washer model 11092573100, we unplug the washer, remove as much water as possible, then clear blockages from the drain hose and the drain pump inlet. Most clogs are lint, coins, or small clothing items trapped at the pump or hose connection.

• Unplug the washer before servicing.
• Turn off both water supply valves.
• Have towels and a shallow pan ready; water will spill when hoses are opened.
• Wear gloves; debris can be sharp.
• If the washer was just running, let the motor and pump cool for a few minutes.

1. Remove standing water: Scoop water out, or use a wet/dry vac at the end of the drain hose.
2. Check the standpipe/sink: Make sure the household drain is not clogged.
3. Inspect the external drain hose:
   • Pull the washer forward.
   • Look for kinks, crushing, or a pinched hose.
   • Detach the hose from the standpipe and flush it with hot water.
4. Check the pump area for a clog:
   • Access the pump from the cabinet (location varies by design).
   • Remove the hose from the pump and clear debris.
   • Spin the impeller by hand; it should turn with slight resistance.
5. Reassemble and test: Reconnect hoses, restore power, then run a short drain/spin to confirm strong flow.

If the hose is clear but draining is still slow or noisy, these parts are the most common fixes for this style of Kenmore top-load washer:

A restricted drain hose or pump makes the washer leave water in the tub, stop mid-cycle, or refuse to spin. Clearing the clog quickly also helps prevent pump damage and reduces the chance of leaks at hose connections.

Last updated: February 2026

To reset your Kenmore 11092573100 washer, we use a simple power reset first: unplug the washer (or turn off the breaker) for 1 minute, then restore power and try a normal cycle. This clears many temporary control glitches.

• Press Pause/Cancel once to stop the cycle.
• Unplug the washer (or switch the breaker off).
• Wait 60 seconds.
• Plug back in (or turn breaker on).
• Wait 30 seconds before pressing any buttons.
• Select Drain/Spin or a Normal cycle and press Start.

A “reset” only helps if the issue is a temporary control lockup. If the problem comes back, we focus on the most common causes for this style of Kenmore top-load washer.

• If it will not drain or it stops full of water: check the water pump WP3363394 for a jam or failure.
• If it agitates or spins weakly (or makes a rattling/grinding noise): inspect the coupling 285753A and the clutch 285785.
• If agitation is weak but the motor runs: check the agitator dog 80040 (common wear item).

Resetting restores the washer’s control to a known “idle” state. If you have to reset repeatedly, that usually points to an intermittent electrical issue (power cord/connection) or a failing drive or drain component that is interrupting the cycle.

Last updated: February 2026

Kenmore model 11092573100 is a standard top-load washer; washers in this design class typically run about 3.2 to 3.6 cu. ft. of tub capacity. Use that range for planning loads, and size loads by basket fill level to prevent poor agitation and out-of-balance spins.

Use these loading targets for the 11092573100:

• Fill the basket loosely, not packed down
• Stop at about 2/3 full for mixed loads (best cleaning)
• Go up to about 3/4 full for towels and jeans (heavier fabrics)
• Wash bulky items one at a time (comforter, large blanket)
• Keep items balanced; mix large and small pieces

Overloading reduces water flow and agitation, leaves detergent residue, and increases strain on the drive and suspension. If the washer struggles to agitate or spin with normal loads, worn drive parts are common causes.

• Coupling 285753A (connects motor to transmission drive)
• Clutch 285785 (helps the basket reach full spin)
• Washer suspension spring WP63907 (helps control tub movement)

Last updated: February 2026