Craftsman 917275021 lawn tractor Parts

A Craftsman “6.75” walk-behind mower does not map to one single model number; “6.75” is an engine power label used across multiple mower models. To get the exact model number, we match the number from your mower’s model tag (not the engine cover) to the correct parts list.

Check these common locations on a Craftsman walk-behind mower:

• Rear of the deck near the discharge chute
• Under the rear bagger door or on the bagger frame
• On the side of the deck near a rear wheel
• On the handle support brackets
• In your paperwork, if you still have the 917275021 owner's manual for your Craftsman equipment

Most Craftsman mower model numbers are a 9-digit format (often starting with 917.). Here is a quick comparison:

Using the correct mower model number ensures you get the right blade, drive belt, air filter, and ignition parts. The same “6.75” marking can appear on different Craftsman decks, and parts like wheels, pulleys, and cables can vary by model.

Model 917275021 is a Craftsman front-engine lawn tractor (48-inch deck, 23.0 HP per the manual), not a 6.75 walk-behind mower. For tractor troubleshooting and maintenance, we follow the procedures in the 917275021 owner's manual.

Last updated: February 2026

Craftsman model 917275021 is a Craftsman front-engine lawn tractor from the mid-2000s era, most commonly placed around 2004 to 2006. For the most accurate confirmation, match the product identification information in your 917275021 owner's manual to the ID tag on your tractor.

We recommend using the tractor’s identification tag and the manual’s model labeling to pin down the exact build timeframe.

• Locate the ID tag (typically under the seat, on the frame rail, or near the engine compartment)
• Confirm the model number reads 917275021
• Record any serial number and product number shown on the tag
• Compare those numbers to the identification information referenced in the 917275021 owner's manual
• If parts have been swapped over time (engine, hood, wiring), rely on the frame tag, not the replaced component

Craftsman tractors in the same “917” family can look similar across multiple years, but small changes affect fit.

• Electrical parts (ignition switch, PTO switch, harness) can vary by production run
• Deck and drive components can change with different sub-variants
• Correct year range helps avoid ordering the wrong hardware sizes and linkages

The manual excerpts confirm the model number and show model-specific parts diagrams and lists for 917275021, which is the best starting point for matching your tractor.

If you are troubleshooting blade engagement while you verify the year, the switch.pto 582107601 is the model-listed PTO switch and is a common failure point when the mower deck will not engage.

Last updated: February 2026

Yes, replacing the engine on your Craftsman lawn tractor model 917275021 is worth it when the tractor is otherwise in solid shape (deck, transmission, steering, and frame) and you want several more seasons of reliable mowing. If multiple major systems are worn out, putting that money toward a replacement tractor is the better value.

• Replace the engine if the deck cuts well, the transmission drives smoothly, and the tractor is structurally sound.
• Replace the tractor if you have engine failure plus recurring drive issues, severe deck rust, or major steering/brake problems.
• Replace the engine if you can do most labor yourself and only need normal tune-up parts afterward.
• Replace the tractor if you will pay full labor and also need several high-cost repairs at the same time.
• Replace the engine if you already have the correct blade/deck setup and want to keep your current attachments.

Use your 917275021 owner's manual to confirm safety system operation and basic maintenance checks before deciding.

• Safety interlock system: The engine should only start with the brake fully depressed and the attachment clutch disengaged; leaving the seat with blades engaged should shut the engine off.
• Deck and blade system: Check for vibration, bent blades, and worn mandrels; the manual calls for tightening blade bolts to 45 to 55 ft-lbs.
• Fuel system condition: Old fuel, clogged filter, or cracked fuel lines can mimic engine failure.
• Drive system: If you have loss of drive, a worn motion drive belt or freewheel control position can be the real issue.

If the total engine swap cost (engine + any required hardware + labor) is over about 50% of the tractor’s current value, replacement usually makes more sense.

An engine swap only pays off when it restores a dependable mower. If the deck, mandrels, belts, and safety circuits are already near end-of-life, you can end up chasing problems even after the new engine is installed.

Last updated: February 2026

For a Craftsman lawn tractor model 917275021, a full engine replacement typically costs $260 to $1,800 installed, depending on the engine, labor rates, and whether related items (belts, wiring, fuel parts) also need service. Plan on about 6 labor hours for a riding mower engine swap.

• Engine type and availability (new vs. rebuilt, exact spec match)
• Labor rate at the shop (often the biggest variable)
• Extra parts found during teardown (fuel lines, filters, pulleys, hardware)
• Electrical and safety circuit condition (switches, wiring, solenoid)
• Fuel system cleanup if old fuel caused varnish or contamination

Many “bad engine” symptoms are actually starting, fuel, or safety-interlock issues. Before committing to an engine, we use these quick checks:

• Battery charged and cables clean/tight
• Starter solenoid and starter engagement
• Safety switches (seat, brake, PTO) working correctly
• Fuel flow and fuel filter condition
• Air filter and spark plug condition

If your blades will not engage or the tractor will not crank, a failed switch can mimic bigger problems; the switch.pto 582107601 is one example of a common electrical control part on this model.

An engine replacement is one of the highest-cost repairs on a riding mower. Verifying the real root cause first helps you avoid paying for an engine when the fix is a battery, wiring, belt, or a safety switch adjustment. For model-specific maintenance intervals and specs (like spark plug type/gap and fuel filter service), follow the 917275021 owner's manual.

Last updated: February 2026

Craftsman riding mower model 917275021 is a front-engine garden tractor; the exact engine make and model are identified on the engine’s ID label (model, type, and code) and in the 917275021 owner's manual. Use that engine ID when buying filters, spark plugs, or carburetor parts.

Use these checks before ordering engine parts or troubleshooting a no-start:

• Find the engine ID label on the blower housing, valve cover, or near the starter
• Record the engine model, type, and code exactly as shown
• Confirm the tractor’s model tag reads 917275021 (commonly under the seat or on the frame)
• Cross-check the engine information with the specifications and maintenance sections in the 917275021 owner's manual
• Use the engine ID, not just the tractor model number, to match tune-up and fuel system parts

The manual describes the tractor configuration (electric start, mower deck size, transmission type) and provides maintenance and repair guidance. The engine ID label is the deciding reference for the engine manufacturer and exact engine series.

Craftsman tractors can use different engines across production runs; the engine ID prevents wrong-part orders and speeds up diagnosis for common issues like hard starting, stalling, or poor cutting performance.

Last updated: February 2026