Kenmore Elite 10650593000 side-by-side refrigerator Parts

On Kenmore Elite refrigerator model 10650593000, the model and serial number label is located inside the fresh food (refrigerator) compartment on the side wall. Open the refrigerator door and look along the left or right interior wall for the rating label (not in the freezer). See the owner's manual for the diagram.

What the label looks like and what to record

The label typically lists key identification details you may need for parts and service.

• Model number (for example, 10650593000)
• Serial number
• Purchase date (you can write this down separately)
• Electrical ratings and other manufacturing information

Quick steps to find it fast

Use these checks to locate the tag without removing shelves.

• Look at eye level first, then scan downward along the side wall
• Check both the left and right interior walls of the refrigerator section
• Use a flashlight; the label can be easy to miss in low light
• Wipe condensation or smudges off the wall so the print is readable
• Take a photo of the label so you have it handy when ordering parts

Common label locations (what to expect)

Location	Most common for this model	Notes
Fresh food compartment side wall	Yes	Listed in the Parts and Features section as the model/serial label location
Ceiling of fresh food compartment	No	More common on some other refrigerator designs
Freezer compartment	No	Not the typical location for this model

Why it matters

We use the exact model number to match the correct Kenmore-compatible parts (such as a water filter, ice maker, or inlet valve) because similar-looking refrigerators can use different shelves, gaskets, and control components.

Last updated: February 2026

For Kenmore model 10650593000, the warranty is 1 year full warranty on the refrigerator plus a 5 year full warranty on the sealed refrigeration system (refrigeration components, connecting tubing, and compressor), both starting from the purchase date. Details and exclusions are listed in the owner's manual.

Warranty coverage at a glance

• 1 year: refrigerator (defects in materials or workmanship)
• 5 years: sealed refrigeration system (sealed system components)
• 30 days (parts only): water filter cartridges (if equipped)
• Coverage applies to private household food storage use
• Proper operation and maintenance per the manual is required

What “sealed refrigeration system” means

The sealed system is the closed-loop cooling circuit. It typically includes:

• Compressor
• Refrigerant tubing/lines
• Evaporator and condenser sections (as part of the sealed circuit)

If you are troubleshooting a cooling issue and suspect a sealed-system component, the parts list for this model includes items such as the refrigerator compressor W10309994 and refrigerator evaporator WP2188823.

Quick comparison table

Item	Warranty length	Notes
Refrigerator (overall unit)	1 year	Defects in materials/workmanship
Sealed refrigeration system	5 years	Includes refrigeration components, tubing, compressor
Water filter cartridges	30 days	Parts only; cartridges are treated separately

Why it matters

Knowing which warranty applies helps you decide whether you are dealing with a general refrigerator issue (often covered for 1 year) or a sealed-system cooling failure (covered longer). It also explains why consumables like filters have a shorter coverage period.

Last updated: February 2026

If your Kenmore Elite 10650593000 side-by-side refrigerator is not cooling, we focus first on airflow, control settings, and heat removal. Blocked air vents, dirty condenser coils, or doors not sealing can quickly raise temperatures; after any control change, allow a full 24 hours to stabilize (per the owner's manual).

Quick checks that fix most “not cooling” complaints

• Confirm the refrigerator is plugged in and the control is not set to OFF.
• Make sure both doors close fully and stay closed.
• Clear packages away from the air vents in both compartments.
• Clean the condenser coils (dirty coils reduce heat transfer and cooling).
• After adjusting temperature controls, wait 24 hours before judging results.
• If the unit was just installed or heavily loaded with warm food, allow 24 hours to cool.

What to check next (common causes)

1) Airflow problems

Cold air has to move from the freezer to the fresh food section. If vents are blocked, temperatures rise even if the compressor is running.

2) Dirty condenser coils

When coils are dirty, the compressor runs harder and cooling performance drops.

3) Door seal (gasket) leaks

If the gasket is not sealing all the way around, warm air leaks in and the refrigerator cannot hold temperature.

Symptom	Most likely area	What we do first
Freezer and refrigerator both warm	Power, controls, condenser coils	Verify power and settings; clean coils
Freezer cold, refrigerator warm	Airflow/vents, evaporator airflow	Clear vents; check for strong airflow
Temps drift up after door use	Door seal, door closing	Inspect gasket contact and door alignment

Parts that often relate to cooling problems

If basic checks do not restore cooling, these model-compatible parts are commonly involved in airflow, defrost, or heat removal issues:

• Refrigerator defrost heater WP2323198 (frost buildup can block airflow)
• Refrigerator defrost bi-metal WPW10225581 (defrost protection and cycling)
• Refrigerator condenser fan W10181323 (moves air across condenser coils)

Why it matters

Running warm can spoil food quickly and forces the compressor to run longer than normal. Fixing airflow restrictions and coil cleanliness first prevents unnecessary part replacement and restores efficient cooling.

Last updated: February 2026

If your Kenmore Elite side-by-side refrigerator model 10650593000 is warm and you hear repeated clicking, loud buzzing, or the compressor never seems to run, the compressor or its start components may be failing. First rule out normal operating sounds and airflow issues using the owner's manual.

What you should check first (fast, no tools)

• Confirm it is actually not cooling: freezer should be near 0°F and fresh food near 37°F.
• Listen for normal sounds: the manual notes you may hear clicking, gurgling, pulsating/high-pitched compressor sounds, and fan airflow during normal operation.
• Check door seal and door closing: poor sealing makes the compressor run longer and cooling suffers.
• Clean condenser coils: dirty coils reduce heat transfer and make the compressor work harder.
• Give it time after changes: after adjusting controls or restoring power, allow 24 hours for temperatures to stabilize.

Signs that point to a compressor problem

These symptoms are strong indicators after the basic checks above are good:

• Clicking every few minutes but the compressor does not stay running (overload cycling)
• No cooling while interior lights work and fans may still run
• Compressor is extremely hot to the touch and shuts off quickly
• Unusual loud humming or grinding from the compressor area
• Breaker trips or the unit repeatedly shuts down when the compressor tries to start

Quick troubleshooting map

What you observe	Most likely area to check next	What it means
Clicking, no steady run	Start device/overload, compressor	Compressor may be struggling to start
Runs constantly, still warm	Airflow, coils, sealed system	Heat not being removed effectively
Fans quiet and warm	Power/control issue	Not always a compressor failure
Loud pulsating but cooling OK	Normal operation	High-efficiency compressor sound can be normal

Parts that are commonly involved (when cooling is poor)

If you confirm airflow and settings are correct, these model-matched parts are often involved in “not cooling” complaints:

• Refrigerator compressor W10309994 (sealed system component)
• Refrigerator condenser fan W10181323 (moves air across condenser coils)
• Refrigerator evaporator fan blade WP2169142 (circulates cold air inside)
• Refrigerator defrost bi-metal WPW10225581 and refrigerator heater WP2323198 (defrost system that prevents ice blockage)

Why it matters

A refrigerator can sound “busy” even when it is healthy; the manual specifically calls out clicking and high-pitched or pulsating compressor sounds as normal in many cases. Checking coils, doors, and airflow first prevents replacing a compressor when the real issue is heat transfer or air circulation.

Last updated: February 2026