Kenmore Elite 11047791701 washer Parts

For Kenmore Elite washer model 11047791701, the exact tub capacity in cubic feet is listed in the product specifications section of the 11047791701 owner's manual. If you are comparing models, most Kenmore Elite front-load washers of this generation are typically in the 3.5 to 4.5 cu. ft. range.

How to find the exact cubic feet for your model

We recommend using the manual specs because “Elite” washers were sold in multiple capacities under similar-looking designs.

• Open the 11047791701 owner's manual
• Look for “Specifications” or “Capacity” (sometimes listed as “tub volume”)
• If capacity is not shown as cubic feet, check for a model feature/spec table near the front
• Use the full model number 11047791701 when comparing online listings or replacement guides

Quick capacity guidance (typical ranges)

Washer type	Typical capacity range
Compact front-load	2.0 to 2.8 cu. ft.
Standard front-load	3.5 to 4.5 cu. ft.
Large front-load	4.5 to 5.5 cu. ft.

Why it matters

Capacity affects how much you can wash per load and how well the washer balances during spin. Overloading can also increase vibration and contribute to drain and spin complaints noted in the troubleshooting guidance in the manual.

Last updated: January 2026

To hard reset your Kenmore Elite washer model 11047791701, disconnect power for about 2 minutes, then restore power and reselect your cycle. If the control is still acting up, cancel the cycle using the STOP button sequence shown in the 11047791701 owner's manual.

Hard reset steps (power reset)

• Press STOP to end the current cycle.
• Unplug the washer (or switch the breaker off).
• Wait 2 minutes.
• Restore power.
• Press POWER, select a cycle, then press and hold START for about 1 second to begin.

If you need a “master reset” during a cycle

Our manual-based reset is to cancel and restart the cycle:

• Select STOP twice to cancel the cycle.
• Select POWER.
• Select the desired cycle.
• Choose any OPTIONS or MODIFIERS you want.
• Press and hold START (about 1 second) to restart.

What to expect after a reset

Situation	What the washer may do	What we recommend
Door stays locked	It may drain automatically before unlocking if water level or temperature is high	Wait for draining to finish, then open the door
Washer won’t start	Door not fully latched or START not held long enough	Close door firmly; hold START for 1 second
Excess water in tub	Cycle was interrupted	Run DRAIN & SPIN after canceling

Why it matters

A hard reset clears temporary control glitches and lets the washer reinitialize the door lock, drain logic, and cycle selection. Canceling correctly also helps prevent a “stuck” cycle state.

Last updated: January 2026

To force your Kenmore Elite washer model 11047791701 to drain, cancel the cycle and run Drain & Spin: press STOP twice, press POWER, select DRAIN & SPIN, then press and hold START for about 1 second to begin draining (see the 11047791701 owner's manual).

Fast steps to drain it now

• Press STOP twice to cancel the current cycle.
• Press POWER.
• Select DRAIN & SPIN.
• Press and hold START (about 1 second).
• Wait for the cycle to finish; the door unlocks when the spin is complete.

If it still will not drain

A drain problem is usually a clog, a kinked hose, or a failing drain pump.

• Check the drain hose for kinks or crushing behind the washer.
• Make sure the drain hose is not shoved too far into the standpipe (it needs an air gap).
• Look for slow draining at the standpipe or laundry tub (a household drain restriction can mimic a washer failure).
• If you hear the pump humming but water does not move, the pump or tub-to-pump hose may be blocked.
• If the washer is completely silent during drain, a control or door lock issue can prevent draining.

Common parts involved (when draining fails)

Symptom	Most common cause	Part to check
Hums but does not drain	Clog in pump or hose	Pump 280187 and washer tub-to-pump hose WPW10467168
Drains slowly	Partial blockage or drain setup issue	Drain hose routing and standpipe
Will not start Drain & Spin	Door not locking or control issue	Door lock and control diagnostics

Why it matters

Forcing a drain the correct way protects the door lock system and helps prevent water from backing up into the tub. Proper drain hose setup also reduces siphoning and repeat drain errors.

Last updated: January 2026

Yes. Kenmore Elite is Kenmore’s premium tier, and the Kenmore Elite washer model 11047791701 is positioned above standard Kenmore washers with more performance-focused design, upgraded features, and stronger ownership support details listed in the 11047791701 owner's manual.

What “high end” means in the Kenmore lineup

Kenmore Elite models are built to deliver higher efficiency and more refined operation than entry and mid-tier Kenmore units.

Typical “premium” indicators include:

• More cycle and option choices for fabric care
• Higher-efficiency washing (HE detergent use)
• Quieter, smoother operation through better vibration control
• More robust core components (common in front-load designs)
• More detailed care and maintenance guidance to protect long-term performance

What the 11047791701 manual signals about premium positioning

The manual for model 11047791701 includes a dedicated Kenmore Elite warranty section and highlights longer-term coverage on major wash-system components.

Manual section or item	What it indicates	What to do as an owner
Kenmore Elite appliance warranty	Premium-line ownership support	Follow operating and care instructions consistently
Long-term coverage on major tub/drum components (per warranty terms)	Focus on durability of core wash parts	Avoid overloading; keep the washer level
Washer care and troubleshooting sections	Designed for long service life with maintenance	Clean regularly; address small issues early

Why it matters

A “high-end” washer pays off in day-to-day results: better cleaning with less water and energy, fewer vibration issues, and longer-lasting core components when the washer is installed and maintained correctly.

Tips to keep Elite-level performance

• Use HE detergent and measure carefully to prevent oversudsing
• Wipe and dry the door boot after loads; replace it if it’s torn (see washer door boot WP8182119)
• Keep the washer level to reduce noise and “walking”
• Check fill performance if cycles run long; a restricted valve can slow filling (see washer water inlet valve WPW10156253)
• Fix draining problems quickly; poor draining affects spin and cleaning

Last updated: January 2026