Kenmore Elite 63013902011 dishwasher Parts

To hard reset your Kenmore Elite dishwasher model 63013902011, cancel the current cycle so the unit drains and returns to a ready state. On this model, holding CANCEL until the WASHING light goes out resets the control after the drain completes (about 1 minute). See the 63013902011 owner's manual for the exact button sequence for your control panel.

Reset steps for model 63013902011

• Open the door.
• Press and hold CANCEL until the WASHING LED goes out.
• Close the door.
• Wait about 1 minute while the dishwasher drains.
• Confirm the COMPLETE LED illuminates (this indicates the unit has been reset).
• If you are changing cycles, press POWER off, then POWER on, and select a new cycle.

If the dishwasher still will not start after a reset

These checks solve most “won’t start” complaints after a cancel/reset:

• Make sure the door is fully closed and latched.
• Confirm Delay start is not set.
• Verify the house breaker or fuse is on.
• Turn on the hot water shutoff valve under the sink.
• Start a short cycle and listen for fill and wash motor operation.

Quick reference: reset vs power cycle

Action	What it does	When to use it
Cancel/reset (hold CANCEL)	Drains and clears the current cycle	Stuck cycle, wrong cycle selected, needs reset
Power off/on	Reboots the user interface after a reset	Controls unresponsive after cancel/reset

Why it matters

A proper cancel/reset clears a “previous cycle not completed” condition and forces a drain, which helps the control accept a new cycle selection and prevents standing water from causing odor or poor cleaning.

Last updated: January 2026

Error 25 (often shown as E25) on a Kenmore dishwasher typically points to a drain problem: the drain pump is blocked, or the drain pump cover is loose or missing. On Kenmore Elite model 63013902011, start by checking for standing water and clearing the filter and drain area.

What to check first (fast, no parts)

• Cancel the cycle and let the unit attempt to drain.
• Remove the lower rack and check the sump area for debris (glass, labels, bones).
• Remove and clean the filter system as described in the 63013902011 owner's manual.
• Inspect the drain hose for kinks, clogs, or a blocked high loop/air gap.
• Check for excess suds (hand soap or too much detergent can slow draining).

Parts that commonly fix an E25-style drain issue

If the drain path is clear but the dishwasher still will not drain, the drain pump or its cover can be the next likely fix.

Symptom	Most likely area	Example part for model 63013902011
Hums but won’t drain	Drain pump jammed or failed	Drain pump 00611332
Leaks or poor drain after cleaning	Pump cover/lid not seated	Lid 00611322
Drains slowly or backs up	Drain hose restricted	Dishwasher drain hose (match routing and length)

Why it matters

A blocked drain pump can leave dirty water in the tub, cause odor, and stop the cycle early. Clearing the filter system and drain path restores normal wash performance and helps prevent repeat drain errors.

Last updated: January 2026

Kenmore Elite dishwasher noise is measured in dBA, and many modern built-in dishwashers operate in a quiet range of about 40 to 50 dBA. For the exact sound rating of model 63013902011, use the specification section in the 63013902011 owner's manual.

Typical dishwasher noise ranges (dBA)

These ranges help you interpret what the number means in a real kitchen:

• 39 to 44 dBA: very quiet, soft wash sounds
• 45 to 50 dBA: quiet, noticeable in a silent room
• 51+ dBA: more noticeable wash and drain noise

Quick comparison table

Noise rating (dBA)	What you usually hear	Best fit for
39 to 44	Low hum, light water movement	Open floor plans, nighttime runs
45 to 50	Gentle wash and occasional drain sounds	Most kitchens
51+	Clearer spray and drain sounds	Closed kitchens, budget installs

If your dishwasher seems louder than expected

A dishwasher can sound louder than its rating when vibration or water flow is affected. Check these common causes:

• Dishes or utensils contacting the spray arm
• Loose toe panel or mounting screws vibrating against cabinets
• Drain hose routing that allows the hose to slap the cabinet (the install guide calls for a raised loop)
• Debris in the sump area causing louder pump sounds
• Drain components wearing and getting noisy during drain-out

If the noise is strongest during draining and you also see slow draining, inspect the drain path and consider the drain pump 00611332 as a key component in that system.

Why it matters

The dBA rating tells you the baseline sound level; changes in sound are often a troubleshooting clue. Noting whether the noise happens during fill, wash, or drain helps narrow the issue to the water inlet, spray system, or drain system.

Last updated: January 2026

On Kenmore Elite dishwasher model 63013902011, the F4E1 service code indicates a water movement problem during washing; the dishwasher is not circulating water as expected. The fastest path to the correct fix is to follow the diagnostic and reset steps in the 63013902011 owner's manual.

What F4E1 usually points to

F4E1 is tied to wash performance and circulation. Common causes include:

• Debris in the filter system or large object trap restricting flow
• A spray arm that is blocked or not turning
• A circulation (wash) pump issue (motor not running or weak)
• Low water level from a fill problem
• Wiring or control issue affecting the pump circuit

Quick checks we recommend first

Shut off power at the breaker before accessing internal components.

• Confirm the dishwasher fills to a normal level (water should cover the sump area)
• Clean the filter system and remove any debris from the trap area
• Spin the spray arms by hand; clear obstructions in the holes
• Run the shortest cycle and listen after the fill for strong wash action
• If the dishwasher does not run at all, use the basic “does not operate” checks in the 63013902011 installation guide

Resetting or clearing the code

Reset steps vary by console layout and control software. Use the model-specific procedure in the 63013902011 owner's manual so the control enters the correct diagnostic or cancel routine.

Reset approach	What it does	When to use it
Cancel/drain routine	Stops the cycle and drains water	After a stalled cycle or to restart cleanly
Diagnostic mode	Tests components and can clear stored faults	After repairs or when troubleshooting

Parts that commonly solve the underlying problem

If the dishwasher fills but does not wash well, these parts are often involved:

• Drain pump 00611332 (if draining is also abnormal)
• Dishwasher water inlet valve 00622058 (if fill is slow or water level is low)
• Circulation pump or motor assembly (select the exact version listed for your model)

Why it matters

When circulation is weak, detergent does not dissolve correctly and spray arms cannot clean. Fixing the root cause prevents repeat fault codes and restores normal wash performance.

Last updated: January 2026