Kenmore Elite 11095876400 dryer Parts

On the Kenmore Elite 11095876400 dryer, the model number is on the model and serial number label located at the top inside the dryer door well. Open the door and look along the upper edge of the door opening for the sticker/plate.

How to find it quickly

• Open the dryer door fully.
• Look at the top inside lip of the door opening (the door well).
• Check for a label that lists both model and serial numbers.
• Wipe dust off the area; the print can be faint.
• Write down the full model number and serial number before ordering parts.

What the label typically includes

Item on label	What it’s used for
Model number	Matching the correct parts diagrams and parts list
Serial number	Identifying production details for service and compatibility
Gas/electrical ratings	Confirming supply requirements and safe setup

Why it matters

We use the exact model number to match your dryer to the correct Kenmore Elite parts list (for example, the right drum support roller, idler pulley, or thermistor). Even small model-number differences can change which parts fit.

Helpful tip before ordering

Use the model number from the label (not the control panel styling) when checking part fit in the parts list and in the owner's manual.

Last updated: February 2026

To reset your Kenmore Elite dryer model 11095876400, unplug it (or switch the breaker off) for 1 minute, then restore power. If the control is simply paused or confused after an interruption, you can also clear the cycle by pressing PAUSE/CANCEL twice, then selecting a new cycle and pressing and holding START.

Quick reset options (try in this order)

• Power reset: Unplug for 1 minute, then plug back in.
• Clear the current cycle: Press PAUSE/CANCEL twice.
• Restart after a stop: Close the door, then press and hold START for about 3 seconds.
• After a power outage: If you see PF, press and hold START to restart.
• Control Locked is on: Press and hold AUTO DRY LEVEL for 3 seconds to unlock.

What “reset” usually fixes

A reset helps when the dryer is not responding, a cycle will not start, or the control panel is stuck after a power interruption. It will not fix a mechanical problem like a broken belt, a seized drum roller, or a failed motor.

Common symptoms and what to do next

Symptom	What to try	What it points to
Dryer will not start	Power reset; then press and hold START	Control needs a reboot or cycle was not started correctly
Dryer stops and shows PF	Press and hold START	Power failure interruption
Buttons do not change settings	Unlock Control Locked	Control lock enabled
Runs but dries poorly	Clean lint screen; check vent airflow	Restricted airflow or venting issue

Why it matters

Resetting the control is the fastest way to recover from a power glitch or an accidental button sequence, and it can save time before you start checking parts like the drive system or airflow components.

For the exact button sequences and indicator meanings for your control panel, use the owner's manual.

Last updated: February 2026

A Kenmore dryer typically lasts 10 to 13 years. With consistent care on your Kenmore Elite 11095876400 (especially lint-screen and vent cleaning), it’s common to reach the high end of that range and avoid the most frequent wear-related breakdowns. See the maintenance section in the owner's manual.

What most affects dryer lifespan

• Airflow maintenance: clean the lint screen every load; keep the exhaust vent clear and uncrushed
• Load habits: avoid overloading; heavy loads strain the drive system and drum supports
• Heat system health (gas models): weak ignition or cycling heat increases run time and wear
• Room conditions: operation is less reliable in spaces below 45°F (7°C)
• Preventive cleaning: remove accumulated lint inside the cabinet periodically

Quick maintenance checklist (best ROI)

• Clean the lint screen after every load.
• Inspect and clean the vent path (dryer outlet to exterior hood) regularly.
• Use rigid or flexible metal venting; avoid crushed or kinked ducting.
• Keep loads sized so items tumble freely.
• If drying times increase, address airflow first before replacing parts.

Common wear items vs. what they impact

Symptom you notice	Likely wear area	Example part for this model
Thumping, squealing, rumbling	Drum support and belt path	Support WPW10314173 or dryer idler pulley 279640
Longer dry times, weak airflow	Lint buildup or blower issue	Dryer blower wheel WP697772
Heat starts then stops (gas)	Ignition or gas valve coils	Dryer gas valve coil kit 279834

Why it matters

A dryer can “run” for years while slowly losing airflow or developing friction in the drum support system. Fixing those issues early helps your 11095876400 dry faster, run cooler, and reduces strain on the drive motor and gas heat components.

Last updated: February 2026