Kenmore Elite 79572059114 refrigerator Parts

To raise your Kenmore Elite refrigerator model 79572059114 off the floor, adjust the two front leveling legs. Turning a leveling leg to the left raises that side; turning it to the right lowers it. Use an 11/16-inch wrench or a flat-blade screwdriver as shown in the owner's manual.

Quick steps to raise the front (leveling legs)

• Unplug the refrigerator if you will be working near wiring or moving it for access.
• Remove the base grille or kick plate (if equipped) to access the leveling legs.
• Use an 11/16-inch wrench or flat-blade screwdriver on the leveling leg.
• Turn the leg left to raise that side; right to lower.
• Have a second person push back gently on the top front of the cabinet to take weight off the legs.
• Adjust both legs in small, equal turns to keep the cabinet stable.
• Recheck door closing; a slight tilt to the rear often helps doors close more easily.

Door alignment vs. raising the cabinet

If your goal is to fix uneven door gaps (not just add clearance), use the door hinge adjustment nut instead of over-raising the cabinet.

Goal	Best adjustment	Where it’s adjusted
More clearance at the front, stop rocking	Front leveling legs	Bottom front corners
Doors not closing easily	Slight rear tilt using both leveling legs	Bottom front corners
Uneven space between fresh food doors	Door alignment nut	Bottom hinge area

Safety and floor-protection tips

• Use two or more people when moving the refrigerator.
• Pull the refrigerator straight out; do not “walk” it side-to-side (this helps prevent floor damage).
• Keep the unit upright; do not tip excessively.
• If you need to roll it for service, raise the front slightly so it rolls easier, then re-level when finished.

Why it matters

Proper leveling keeps the refrigerator stable, helps the doors seal correctly, and can reduce frost, temperature swings, and water or ice maker issues caused by poor door closure.

Last updated: February 2026

On Kenmore Elite model 79572059114, you adjust door height at the bottom hinge using the adjustable nut. Turn the nut to the right to raise the door or to the left to lower it, then recheck the gap between the two fresh food doors for an even alignment. See the owner's manual for the exact hinge location and illustrations.

Before you start

• Unplug the refrigerator or switch off power to avoid accidental dispenser or light operation.
• Remove heavy items from the door bins to reduce weight on the hinge.
• Keep the doors closed as much as possible so the cabinet stays stable.
• Have a helper gently push back on the top of the refrigerator if you also need to level it.

Step-by-step: adjust the door height

1. Open the door you need to adjust and locate the adjustable nut on the bottom hinge.
2. Use the wrench included with the Use & Care Guide (or a correctly sized wrench) on the nut.
3. Turn the nut:
   • Right (clockwise) to raise the door
   • Left (counterclockwise) to lower the door
4. Close both doors and check:
   • The space between doors is even
   • Doors close smoothly without rubbing
5. Repeat in small turns until the doors align.

If the doors still do not close easily

Door alignment and cabinet leveling work together. If the refrigerator feels unsteady or the doors do not self-close well, adjust the front leveling legs to tilt the cabinet slightly to the rear (both legs the same amount). The owner's manual covers the leveling-leg directions and tool size.

Quick reference

Adjustment	What to turn	Direction	Result
Door height	Bottom-hinge adjustable nut	Right	Raises door
Door height	Bottom-hinge adjustable nut	Left	Lowers door
Door closing feel	Front leveling legs	Adjust evenly	Improves closing and stability

Why it matters

Even door height helps the door gaskets seal correctly, prevents warm air leaks, and reduces frost and temperature swings in the fresh food and freezer sections.

Last updated: February 2026

Common issues on the Kenmore Elite 79572059114 bottom-mount refrigerator include warm temperatures after a power interruption, longer-than-expected run time while it stabilizes, ice maker overproduction, door sealing or leveling problems, and normal clicking or whooshing noises that can sound alarming. Use the owner's manual troubleshooting section to match symptoms to the right fix.

Most common symptoms and what they usually mean

• Not cooling or slow to cool: after moving or restoring power, cooling can take up to 24 hours to fully stabilize.
• Runs a lot: frequent door openings, adding warm food, or initial cool-down can keep the compressor running longer.
• Ice maker makes too much ice: the shutoff arm or electronic sensor path is blocked; clearing the bin area typically restores normal cycling.
• Noises (clicking, rattling, whooshing, gurgling): often normal operation (defrost cycle clicks, fans moving air, refrigerant flow).
• Door hard to open or poor seal: pressure equalization after closing can make the door feel stuck; dirty or sticky gaskets can also cause sealing issues.
• Wobbling or unstable cabinet: leveling legs need adjustment; shims may be needed on uneven floors.

Quick checks we recommend first (in order)

1. Confirm the refrigerator is not in Demo Mode.
2. If power was just restored, allow 24 hours for temperatures to recover.
3. Make sure doors close fully; clean gasket surfaces and the cabinet contact area.
4. Check for airflow restrictions (do not block vents with food packages).
5. If ice production is abnormal, empty the bin and clear the shutoff arm or sensor area; then wait 24 hours.
6. If you hear new noises, compare them to the “normal operation” sounds in the manual.

Symptom-to-part areas (helpful for troubleshooting)

Symptom	Most likely area to inspect	Example part on this model page
Warm fridge/freezer, poor cooling recovery	Sealed system or cooling components	Refrigerator compressor TCA38091801
Water dispenser slow or no water	Water supply and valve	Refrigerator water inlet valve AJU72992603
Ice maker issues (no ice, odd cycling)	Ice maker module and sensors	Refrigerator ice maker assembly AEQ73110203
Frost buildup, temperature swings	Defrost sensing and control	Refrigerator defrost sensor assembly 6615JB2005R

Why it matters

Catching the difference between normal behaviors (defrost clicks, fan whoosh, 24-hour cool-down) and true failures (persistent warm temps, repeated leaks, ice maker overflow) prevents unnecessary part replacement and helps you focus on the right system first.

Last updated: February 2026

On Kenmore Elite refrigerator model 79572059114, dH (or Er dH) indicates a defrost heating problem. The refrigerator is detecting that the evaporator is not warming up as expected during the defrost cycle, which can lead to frost buildup and poor cooling.

What to check first (quick, safe steps)

• Power reset: unplug the refrigerator (or turn off the breaker) for 5 minutes, then restore power.
• Make sure the doors close fully and the gaskets seal; warm air leaks can worsen frost and trigger defrost-related errors.
• Listen for the evaporator fan running; weak airflow can mimic a defrost issue.
• Check for heavy frost on the freezer back wall; that is a strong sign the defrost system is not clearing ice.
• If the display is locked, unlock controls before trying any diagnostic steps (see the owner's manual).

Likely causes on this model

In most Kenmore 795 bottom-mount designs, dH points to a failure in one of these areas:

• Defrost sensor or temperature sensor out of range
• Defrost heater circuit problem (heater, wiring, or connection)
• Main control not driving the defrost circuit correctly
• Ice buildup restricting airflow across the evaporator

Parts that commonly relate to a dH/defrost issue

What it affects	What you may notice	Example part on this model
Defrost sensing	Frost returns quickly after a manual defrost	Refrigerator defrost sensor assembly 6615JB2005R
Defrost sensing (alternate sensor listing)	Temperature readings seem erratic	Refrigerator defrost sensor assembly ACM73919214
Cooling control	Defrost never seems to start or complete	Lg refrigerator electronic control board EBR75234703

Why it matters

When the defrost system cannot melt frost off the evaporator, airflow drops and temperatures rise. That can cause warm refrigerator temps, soft ice cream, longer run times, and eventually no-cool conditions.

When to stop and get service

If you see heavy ice buildup, burning smell, repeated tripping of a breaker, or the error returns quickly after a reset, we recommend having a qualified technician diagnose the defrost circuit and control safely.

Last updated: February 2026