Kenmore 11027122310 commercial washer Parts

The exact cubic-feet capacity for Kenmore commercial washer model 11027122310 is not listed in the installation instructions; most Kenmore top-load washers in this design family are typically about 3.2 to 3.5 cu. ft. For the most accurate number, confirm by measuring the wash basket.

How to measure capacity (most accurate)

Use the basket dimensions to calculate cubic feet.

• Unplug the washer and open the lid.
• Measure the inside diameter of the basket (in inches).
• Measure the usable depth to the normal fill line (in inches).
• Calculate: Capacity (cu. ft.) = (π × (diameter/2)² × depth) ÷ 1728.
• Round to one decimal place.

Quick reference table

What you measure	Where to measure	Why it matters
Inside diameter	Across the basket, inside wall to inside wall	Sets the tub “footprint”
Usable depth	Bottom of basket to typical waterline	Prevents overestimating
Calculated cu. ft.	Use the formula above	Gives a model-specific capacity

Typical capacity range for this style of Kenmore washer

For many Kenmore 110-series, belt-driven top-load designs, capacity commonly falls in this range:

• Standard to large: ~3.0 to 3.5 cu. ft.
• Extra-large (some variants): ~4.0+ cu. ft.
• Commercial versions: often prioritize durability and turnover over maximum volume

Why it matters

Capacity affects load sizing, detergent amount, and cycle performance. Overloading can cause poor agitation, longer drain times, and extra wear on drive components like the belt and pulley.

Related parts and resources

If you are troubleshooting performance issues that feel like “low capacity” (poor turnover, slow spin, or slipping), these model-matched parts are common checks:

• Washer drive belt WPW10006384
• Whirlpool washer drive pulley W10721967

For installation specs (including drain and electrical requirements), use the installation guide. If you need to order parts by model number, search on Sears PartsDirect.

Last updated: February 2026

Most Kenmore washers average 10 to 15 years of service life. For the Kenmore 11027122310 commercial washer, lifespan lands in that same range, but heavy daily use shortens it; correct installation and routine maintenance extend it (see the installation guide).

Typical lifespan by use level

Commercial-style machines like model 11027122310 often see very different results depending on how many loads you run.

Use pattern	Typical lifespan expectation	What usually ends it first
Light (few loads/week)	12 to 15 years	Hoses, valve, belt wear
Moderate (daily)	10 to 12 years	Drain pump, suspension, drive system
Heavy (many loads/day)	7 to 10 years	Drive components, motor, control issues

What extends the life of your 11027122310

We see these steps make the biggest difference on belt-drive top-load commercial washers:

• Keep the washer level; an unlevel cabinet increases vibration and wear.
• Stay within the washer’s load limits; chronic overloading accelerates belt and suspension wear.
• Use correct water supply pressure; the installation instructions call for 20 to 100 psi.
• Avoid installing on carpet; a firm, level floor reduces movement and stress.
• Inspect for small leaks and fix them early (hoses, clamps, inlet valve connections).

Parts that commonly affect “end of life” decisions

If the washer stops spinning, won’t drain, or becomes very noisy, these are frequent repair points:

• Washer drive belt WPW10006384 (slipping, burning smell, no spin)
• Washer drain pump assembly WPW10276397 (won’t drain, humming, intermittent draining)
• Damper assembly W10780046 (excessive shaking, banging, out-of-balance behavior)
• Washer water inlet valve WPW10486031 (slow fill, no fill, hot or cold fill problems)

Why it matters

A washer near the end of its lifespan typically shows up as repeat failures (drain, spin, vibration) and longer cycle times. Knowing the 10 to 15 year baseline helps you decide whether a repair is a smart reset (belt, pump, valve) or whether multiple major repairs are stacking up.

For ordering, we list replacement parts for Kenmore 11027122310 on this page; you can also search by model number on Sears PartsDirect.

Last updated: February 2026

To hard reset your Kenmore washer model 11027122310, unplug it (or switch off the breaker) for 1 minute, then restore power and start a new cycle. This clears a temporary control glitch without changing any coin-slide settings or installation setup; see the installation guide for safety basics.

Hard reset steps (safe, no tools)

• Press Power/Cancel to stop the cycle.
• Unplug the washer or turn OFF the dedicated breaker.
• Wait 60 seconds (full minute).
• Restore power.
• Select a cycle and press Start.
• If the controls are still unresponsive, repeat once with a 5-minute power-off.

If it still will not start after a reset

A reset helps only when the control is “stuck.” If the washer still will not run, focus on power, draining, and drive components that commonly stop a commercial top-load washer.

• Confirm the washer is plugged into a grounded 3-prong outlet.
• Check for a drain issue (standing water can prevent advancing); inspect the washer drain pump assembly WPW10276397.
• If you hear the motor but the basket does not move, inspect the washer drive belt WPW10006384 and whirlpool washer drive pulley W10721967.
• If the tub is violently out of balance, check suspension; the damper assembly W10780046 is a common fix.

Quick symptom guide

What you see	What the reset fixes	What to check next
Dead panel, no response	Temporary control lockup	Outlet, breaker, power cord connection
Hums but will not spin/agitate	Rarely	Belt, pulley, gear case
Will not drain, stops mid-cycle	Sometimes	Drain pump, drain hose, clogs
Lid locks and cycle will not proceed	Sometimes	Drain condition, load size, control behavior

Why it matters

A hard reset is the fastest way to clear a momentary electronic control error on the 11027122310. If the same symptom returns, a mechanical issue (drain, drive, or suspension) is usually the real cause, and replacing the correct part from the model-specific list on this page or searching by model at Sears PartsDirect prevents mismatches.

Last updated: February 2026

Kenmore washer model numbers are structured so the first 3 digits identify the manufacturer, the next set of digits identifies the base design, and the remaining digits indicate feature or production variations. For your Kenmore commercial washer model 11027122310, the full number is the key to getting the correct parts and installation details in the installation guide.

What each section of a Kenmore model number tells you

Most Kenmore model numbers follow this pattern:

• Prefix (first 3 digits): identifies who built the washer for Kenmore
• Core model digits (middle group): identifies the base platform and major design
• Suffix digits (ending group): identifies revisions such as color, feature set, or production changes

Example using your model

Example model	Prefix	Middle digits	Suffix	What it helps with
11027122310	110	27122	310	Matching the correct parts list and documentation

Why using the full model number matters

Small digit changes can point to different internal components, even when two washers look the same. Using the exact model number helps us match the right drive system, drain components, and controls.

Common parts that can vary by model revision include:

• Drive belt and pulley style
• Drain pump design
• Water inlet valve configuration
• Control board and console parts
• Suspension and tub components

Parts lookup tips for model 11027122310

When you are ordering or troubleshooting, we recommend:

• Match the model number on the washer’s model tag exactly to 11027122310
• Use the parts list for this model first; then search by part ID if needed
• If you are diagnosing a no-spin or squeal issue, check common drive items like the washer drive belt WPW10006384 and whirlpool washer drive pulley W10721967
• For drain or no-drain symptoms, confirm the correct pump such as the washer drain pump assembly WPW10276397
• For broader model-number and parts-search help, use Sears PartsDirect

Why it matters for installation and service

This Kenmore commercial washer family includes coin-slide and meter-case variations. The correct model number ensures you follow the right setup steps and hardware expectations (for example, coin slide and coin box components may be sourced separately depending on the exact configuration).

Last updated: February 2026