Kenmore 11078132410 gas dryer Parts

To hard reset your Kenmore gas dryer model 11078132410, unplug the dryer (or switch the breaker off) for 1 to 5 minutes, then restore power and start a cycle. This clears many temporary control glitches and lets you restart normally using the START/PAUSE procedure in the owner's manual.

Hard reset steps (safe, standard method)

• Turn the dryer OFF.
• Unplug the power cord (or turn the dryer circuit breaker OFF).
• Wait 1 to 5 minutes.
• Restore power.
• Select a cycle, then touch and hold START/PAUSE for up to 3 seconds to begin.

If the dryer still will not start after a reset

These checks solve the most common “looks dead” or “won’t run” situations on 11078132410:

• Door not fully closed: close firmly until it latches.
• START/PAUSE not held long enough: use the pad of your finger and hold up to 3 seconds.
• Power supply issue: check the household breaker or fuses (some homes use more than one).
• Cycle selector not set: rotate the knob until a cycle lights up (a blank display can happen when it is not on a cycle).
• Wrinkle Guard pause behavior: if the door was opened during Wrinkle Guard, use Power to turn off or press START/PAUSE to continue.

What a reset does (and does not) fix

A hard reset is best for temporary electronic states. It will not correct a failed safety device or heating component.

Symptom after reset	What it usually points to	Common next step
Display shows PF	Power failure interruption	Press START to clear, then press and hold START to resume
Dryer runs but heat is inconsistent	Gas ignition components	Check igniter and flame sensing; consider dryer valve coil kit 279834
Dryer shuts off or won’t run after overheating	Airflow restriction or safety fuse	Clean venting; if needed, test/replace thermal fuse W10909685
“Check Vent” indicator	Blocked or restricted venting	Clean lint screen and entire vent path

Why it matters

Resetting is a fast first step, but airflow and starting technique matter just as much. Restricted venting can trigger overheating symptoms, longer dry times, and repeated shutdowns, even after a successful reset.

For parts and diagrams specific to model 11078132410, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

Common problems on Kenmore dryers like model 11078132410 fall into three buckets: won’t start, won’t heat or takes too long to dry, and loud or thumping noises. Most fixes start with power, airflow (lint and venting), and a few high-wear parts listed in the 11078132410 owner's manual.

Most common symptoms and what usually causes them

• Dryer won’t run: door not fully closed, START/PAUSE not held long enough, tripped breaker or blown fuse, or incorrect power supply.
• Dryer runs but won’t heat (gas models): gas shutoff valve closed, weak ignition components, or a safety device opened due to overheating.
• Long dry times: restricted venting, lint buildup, or poor airflow.
• Loud squealing, rumbling, or thumping: worn drum support rollers, idler/bracket wear, or a damaged belt.
• Intermittent heat: failing gas valve coils or a temperature-sensing issue.

Parts that commonly fix these problems (for 11078132410)

If troubleshooting points to a worn or failed component, these are frequent replacements for this model:

• Dryer drum support roller WPW10314173 (rumbling, thumping)
• Belt-4 rib, W10849499 (drum not turning)
• Dryer valve coil kit 279834 (burner lights then shuts off, intermittent heat)
• Igniter 279311 (no ignition)
• Thermal fuse W10909685 (dryer won’t run or stops due to overheating)

Quick checks we recommend before replacing parts

1. Confirm the dryer is set to a heated cycle (not Air Only).
2. Verify the door is fully closed and you touch and hold START/PAUSE up to 3 seconds.
3. Check the home breaker/fuses (many dryers use two).
4. For gas dryers, confirm the gas supply valve is open.
5. Clean the lint screen and inspect the vent path for crushing or blockage.

Symptom-to-fix guide

Symptom	Most likely starting point	Common part if needed
Won’t start	Door, START/PAUSE, breaker/fuses	Thermal fuse W10909685
Runs, no heat	Gas valve open, airflow, ignition	Igniter 279311 or dryer valve coil kit 279834
Loud rumble/thump	Drum support wear	Dryer drum support roller WPW10314173
Drum won’t spin	Belt and drum support system	Belt-4 rib, W10849499

Why it matters

A restricted vent or lint buildup can cause overheating, nuisance shutdowns, and repeated thermal fuse failures. Fixing airflow first protects the heater system, improves dry times, and helps parts last longer.

You can order replacement parts for Kenmore 11078132410 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

Most Kenmore dryers, including the Kenmore gas dryer model 11078132410, typically last 10 to 13 years with normal household use. Regular vent cleaning, lint removal, and replacing wear items (like a belt or drum rollers) on time are what most often push lifespan past that range. See the owner's manual for the maintenance schedule and operating tips.

What affects dryer lifespan the most

A dryer’s life is usually determined by heat stress, airflow, and normal wear on moving parts.

• Airflow and venting: restricted venting overheats the dryer and shortens component life
• Lint control: a clogged lint screen housing increases drying time and heat buildup
• Load size: frequent overloading strains the drum, belt, and support rollers
• Cycle selection: high heat on every load accelerates wear on thermostats and fuses
• Timely repairs: replacing a noisy roller early prevents secondary damage

Common wear parts that extend life when replaced

On model 11078132410, these are typical “keep it running” parts when symptoms show up:

Symptom	Likely wear area	Example part on this model page
Thumping, rumbling, squealing	Drum support and drive system	Dryer drum support roller WPW10314173
Drum not turning, burning rubber smell	Belt or idler system	Belt-4 rib, W10849499
Runs but no heat or heat cuts out	Gas ignition or safety devices	Dryer valve coil kit 279834

Why it matters

A gas dryer that is kept cool with strong airflow dries faster, uses less energy, and avoids repeated overheating that can trip safety devices (like a thermal fuse) and shorten the life of the motor, blower wheel, and controls.

Quick maintenance routine we recommend

Use this simple routine to get the longest service life:

• Clean the lint screen every load
• Check airflow at the outside vent hood monthly
• Clean the full vent duct run at least yearly (more often with long vents)
• Avoid overloading; keep loads loose so air can tumble through
• If you see an F# E# style code, follow the troubleshooting guidance in the owner's manual

You can order replacement parts for Kenmore 11078132410 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

The Kenmore 11078132410 is a full-size 27-inch gas dryer; dryers in this platform are typically in the 6.5 to 7.4 cu. ft. range. For the exact rated capacity for your specific unit, use the specifications section of the 11078132410 owner's manual.

How to find the exact capacity (fastest method)

Use the model-specific documentation first, then confirm it matches your unit’s ID label.

• Open the 11078132410 owner's manual and look for “Specifications”, “Capacity”, or “Drum volume”
• Confirm the model family listed includes 110.7813*410 (the asterisk is the color code)
• Check your dryer’s model tag (commonly inside the door opening) to verify 11078132410 matches
• If multiple models are listed, match the exact model line for your dryer before using the spec

Typical capacity guide (for planning loads)

Use this as a practical reference for load sizing while you confirm the exact spec.

Dryer size class	Typical capacity	Common use
Compact (24-inch)	3.4 to 4.4 cu. ft.	Apartments, small loads
Standard 27-inch	6.5 to 7.4 cu. ft.	Most households
Large 27-inch	7.5+ cu. ft.	Bulky items, larger families

Why it matters

Capacity affects tumbling space and airflow. When the drum is overloaded, clothes do not lift and separate well; drying times increase and heat and mechanical wear go up.

Parts that often show wear when loads are consistently too large

If you notice rumbling, thumping, or squealing, these common wear items are worth checking.

• Drum support wear and noise: dryer drum support roller WPW10314173
• Belt and pulley wear (slipping, squeal): dryer repair kit 4392067
• Air movement issues (long dry times): dryer blower wheel WP697772

Ordering parts

You can order replacement parts for Kenmore 11078132410 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026