Kenmore Elite 66514749N513 dishwasher Parts

To take your Kenmore Elite dishwasher model 66514749N513 out of lock mode, press and hold TOP RACK ONLY for 3 seconds until the Locked indicator light turns off. The door can still open and close while the controls are locked; the dishwasher just will not start.

• If Locked is lit, press and hold TOP RACK ONLY for 3 seconds.
• If it will not unlock right away, wake the controls first by pressing START/RESUME or CANCEL/DRAIN.
• You can also wake the controls by opening and closing the door, then try TOP RACK ONLY again.
• Confirm the Locked light turns off (buttons should respond normally).
• Start a cycle by pressing START/RESUME.

For the exact button layout and indicator-light behavior on your control panel, use the 66514749N513 owner's manual.

Control Lock prevents unintended button presses between cycles. If it is on, the dishwasher cannot start even though power is available and the door latches normally.

Last updated: January 2026

To hard reset the Kenmore Elite dishwasher model 66514749N513, we reset the control by using the CANCEL/DRAIN button sequence described in the 66514749N513 owner's manual. This clears the current cycle so you can restart with fresh cycle and option selections.

1. Open the door slightly to stop the cycle; wait for spraying to stop.
2. Open the door fully.
3. Press START/RESUME.
4. Press and hold CANCEL/DRAIN twice to reset the control.
5. Select your new cycle and options.
6. Press START/RESUME, then close the door within 3 seconds.

• The dishwasher may run a short drain if water is in the bottom.
• Indicator lights may change as the control clears the cycle.
• If the door is not closed within 3 seconds after pressing START/RESUME, the dishwasher will beep and not start.

These checks solve the most common “looks reset but won’t run” situations:

• Make sure the door is fully latched; a weak latch can prevent starting.
• Confirm the cycle is selected, then press START/RESUME and close the door within 3 seconds.
• If the tub is full of water, let CANCEL/DRAIN run until draining finishes.
• Check for a control lock indicator light (locked controls will ignore button presses).
• If you suspect a door-latch problem, inspect the dishwasher door latch WPW10653840 for damage or looseness.

A true control reset clears a stuck cycle or invalid option selection, restores normal button response, and helps you restart cleanly without guessing. It is also a fast first step before replacing parts like a door latch or control.

Last updated: January 2026

Yes. Many Kenmore dishwashers are designed to run quietly, and your Kenmore Elite dishwasher model 66514749N513 is built for low-noise operation when it’s installed level, secured correctly, and the spray system is running smoothly. For the exact sound rating (dBA) and cycle details, use the 66514749N513 owner's manual.

Dishwasher noise is typically measured in dBA (decibels A-weighted). Lower numbers are quieter.

If your 66514749N513 seems louder than it used to, these are the most common causes we see:

• Dishes or utensils touching the spray arm (rattling or ticking)
• The dishwasher not level or not secured tightly in the cabinet opening
• A worn rack wheel or adjuster causing the rack to vibrate
• Food debris in the filter area or sump causing grinding sounds
• A drain pump or circulation system issue (buzzing, humming, or growling)

1. Confirm the unit is level and firmly mounted (installation steps are in the 66514749N513 installation guide).
2. Re-load so nothing hangs below the lower rack or blocks the spray arms.
3. Clean the interior and follow the routine care steps in the manual.
4. Inspect rack hardware for looseness or wear; a damaged roller can make the rack chatter.

If the noise happens mainly when sliding racks in and out, these model-matched parts are common fixes:

• Dishwasher rack adjuster W10712395 (upper rack height/position issues)
• Dishwasher dishrack roller assembly, lower WPW10195417 (lower rack rolling noise)

A dishwasher that suddenly gets louder often has a loading, mounting, or wear issue. Fixing it early helps prevent broken dishes, poor wash performance, and premature wear on rack components.

Last updated: January 2026

On Kenmore Elite dishwasher model 66514749N513, F4E1 is a diagnostic-style fault code that indicates the control detected a problem during a wash-related function (water movement, heating, or sensing). We use the model’s tech sheet procedures to pinpoint the exact cause and clear the fault correctly.

• Cancel the cycle and let the dishwasher drain.
• Turn power off at the breaker for 1 minute, then restore power.
• Start a quick cycle and listen for normal wash action (spray sound) after filling.
• Check and clean the filter area and sump for debris.
• If the code returns, run the model’s diagnostic routine from the tech sheet.

These are the most frequent issues on dishwashers in this Kenmore 665 platform:

Use the diagnostic and fault-clearing steps listed for your exact control panel and platform in the 66514749N513 owner's manual. If you are reinstalling the dishwasher or checking wiring connections, follow the 66514749N513 installation guide for safe access and routing.

F4E1 usually shows up when the dishwasher cannot complete a key wash function. Fixing the underlying cause restores proper spray pressure, heating performance, and cycle completion, which directly affects cleaning results.

Last updated: January 2026