Owner’s manual
Error Codes
How to replace an ice maker in a side by side refrigerator?
To replace the ice maker in your Kenmore 10658906801 side-by-side refrigerator, we shut off the water supply, turn the ice maker OFF, remove the ice bin, swap the ice maker assembly, then restore water and power. After installation, allow time for ice production to return to normal.
- Unplug the refrigerator or switch off power at the breaker.
- Turn off the water supply to the refrigerator (recommended before any ice maker work).
- Turn the ice maker OFF using the freezer on/off control (the switch is on the top right side of the freezer compartment per the owner's manual).
- Remove the ice storage bin from the freezer door.
- Protect the floor with towels in case a water line drips.
- Remove the ice bin: Hold the base with both hands, press the release button, and lift the bin up and out.
- Access the ice maker: Remove the cover (if present) and locate the mounting screws and wiring harness.
- Disconnect wiring: Unplug the ice maker harness connector.
- Remove the old ice maker: Support it with one hand while removing mounting screws.
- Install the new ice maker: Mount the replacement, reconnect the harness, and reinstall any covers.
- Reinstall the ice bin and close the freezer door.
- Turn water and power back on, then turn the ice maker ON.
The manual guidance for ice production applies after replacement:
| What you see | What it means | What to do |
|---|---|---|
| No ice right away | Normal startup | Allow 24 hours for the first batch of ice |
| Slow production | Normal fill cycle | Allow up to 3 days to completely fill the bin |
| Cloudy or odd-tasting early ice | System flushing | Discard the first three batches of ice |
If the ice maker still will not produce ice after replacement, these related parts often matter:
- Refrigerator ice maker 2198597 (complete ice maker assembly)
- Refrigerator inlet valve W10408179 (controls water flow to the ice maker)
- Genuine Kenmore refrigerator water filter EDR3RXD1 (a restricted filter can reduce water flow)
An ice maker depends on steady water pressure, a working inlet valve, and correct on/off control operation. Replacing the ice maker fixes mechanical and electrical failures, but water supply issues can still prevent ice production.
Last updated: February 2026
How wide is a Kenmore side by side refrigerator?
Most Kenmore side-by-side refrigerators are 33 to 36 inches wide. For your specific Kenmore model 10658906801, use the dimension and clearance guidance in the 10658906801 owner's manual and measure your cabinet opening so you know the refrigerator and doors will fit.
These are the common exterior width classes for side-by-side refrigerators:
- 33-inch class: narrower footprint
- 35 to 36-inch class: most common full-size width
- 42-inch class: built-in style (less common)
| Side-by-side style | Typical exterior width | What changes most |
|---|---|---|
| Standard depth | 33 to 36 in. | Depth and door swing |
| Counter-depth | 33 to 36 in. | Depth (shallower), width often similar |
| Built-in | About 42 in. | Cabinet opening requirements |
Measure both the refrigerator and the space, then compare.
- Measure the opening width at the top, middle, and bottom
- Measure the refrigerator cabinet width (main box, not including handles)
- Check overall width with doors and handles (handles can add clearance needs)
- Plan for door swing next to walls or cabinets
- Follow ventilation and clearance guidance; the manual calls out 1/2 inch space on each side and at the top, and 2 inches minimum next to a fixed wall (depending on model) for door swing
Width alone does not guarantee a good install. Door swing clearance and ventilation space affect everyday use, temperature performance, and whether the ice maker and water line routing fit cleanly.
Last updated: February 2026
Where is the model number on a Kenmore side by side refrigerator?
On Kenmore side-by-side refrigerator model 10658906801, the model number is printed on the appliance identification label (the same label that lists the serial number). We use that label information to match the correct parts list and the correct owner's manual for your refrigerator.
Look for a paper or foil label in these typical spots on a Kenmore side-by-side:
- Inside the fresh food (refrigerator) compartment on a side wall
- Along the ceiling of the fresh food compartment near the light housing
- On the cabinet frame around the door opening (near the hinges)
- Behind the base grille area at the bottom front (less common)
- On the back exterior panel (least convenient, but possible)
The label usually shows both a model number and a serial number. For ordering parts, we match by model number first.
| What you see on the label | What it’s used for | Example format |
|---|---|---|
| Model number | Identifies the exact design and parts | 10658906801 |
| Serial number | Identifies the production unit | Letters plus numbers |
Kenmore side-by-side refrigerators can look similar across multiple model numbers, but parts like the water filter, ice maker, inlet valve, and electronic control can vary by model. Using the exact model number helps us point you to the right diagrams and compatible replacement parts.
- Use a flashlight and check the cabinet walls near the crisper drawers.
- Wipe the label gently with a damp cloth; grease and dust can hide digits.
- Write the model number down exactly as shown (all digits, no spaces).
Last updated: February 2026
