Kenmore Elite 11095089402 dryer Parts

To reset a Kenmore Elite dryer model 11095089402, we recommend doing a simple power reset first: turn the dryer off, unplug it (or switch the breaker off) for 1 minute, then restore power and start a cycle. This clears many temporary control glitches.

Recommended reset steps (safe and effective)

• Press PAUSE/CANCEL twice to stop the dryer and clear the current settings.
• Unplug the dryer (or turn the breaker off) for 1 minute.
• Restore power.
• Close the door firmly.
• Select a cycle and options again.
• Press and hold START for about 3 seconds to begin.

If the controls still will not respond

A “reset” issue is often a control lock or a cycle that needs to be fully canceled.

• If Control Locked is on: press and hold AUTO DRY LEVEL for 3 seconds to unlock.
• If the dryer was paused: close the door and press and hold START to resume.
• If the cycle was interrupted for more than 5 minutes: reselect the cycle settings before restarting.

Quick reference table

Symptom	What to do	What it fixes
Dryer acting “frozen”	Unplug 1 minute, then restart	Clears temporary electronic glitches
Need to fully stop and clear	Press PAUSE/CANCEL twice	Cancels cycle and clears settings
Buttons do not work, lock light on	Hold AUTO DRY LEVEL 3 seconds	Turns off Control Locked

Why it matters

Resetting the control correctly prevents repeated shutdowns and helps you avoid misdiagnosing a normal feature (like Control Locked) as a failed electronic control board.

For model-specific button sequences and indicator meanings, follow the 11095089402 owner's manual.

Last updated: January 2026

For Kenmore Elite dryer model 11095089402, the display code called out in the troubleshooting section is PF (power failure). This model can also show E1, E2, or E3 as service codes; those indicate the dryer needs professional diagnosis. Use the 11095089402 manual to confirm the message and the exact restart steps.

Common display codes you can see

These are the code messages referenced for this Kenmore Elite dryer:

• PF: Power failure interrupted the cycle.
• E1: Service code (fault detected).
• E2: Service code (fault detected).
• E3: Service code (fault detected).

What to do when you see a code

Start with the safe, no-parts steps below before assuming a control or sensor failure.

• For PF, press and hold START to restart the dryer.
• Verify the dryer is plugged in and the breaker is fully reset.
• Check that the door closes firmly and the cycle actually starts.
• Clean the lint screen and confirm strong airflow at the outside vent hood.
• If it is a gas dryer, confirm the gas shutoff valve is fully open.

Quick reference table

Code	What it means	What we do first
PF	Cycle was interrupted by a power loss	Press and hold START to restart
E1 / E2 / E3	Service code; a fault was detected	Reset power, then schedule service/diagnostics

Why it matters

A PF message is usually a simple restart after an interruption. E1/E2/E3 are service codes; treating them as a parts-shopping list often leads to unnecessary replacements and repeat problems.

Last updated: January 2026

On the Kenmore Elite dryer model 11095089402, the moisture sensor is a pair of metal strips mounted inside the drum area, positioned so clothes brush across them during Auto Dry cycles. These sensor bars “feel” remaining moisture and help the control adjust drying time automatically (Auto Moisture Sensing).

How to find it on model 11095089402

In most Kenmore Elite dryers that use Auto Moisture Sensing, the sensor bars are located:

• On the inside front bulkhead (front panel area inside the drum opening)
• Low enough that tumbling clothes regularly contact the strips
• Connected to the wiring harness with two wires
• Accessible after removing the lint screen housing or front access components on some builds

For the exact access steps and panel removal sequence for your configuration, follow the disassembly and care guidance in the 11095089402 owner's manual.

What the moisture sensor does (and why it matters)

The manual explains that Auto Moisture Sensing uses two metal strips (sensors) located on the inside of the dryer to detect moisture as clothes pass. When the sensor readings change, the dryer adjusts the estimated time remaining and helps prevent over-drying.

Why it matters

A dirty or coated sensor can cause:

• Cycles that end too soon (clothes still damp)
• Cycles that run too long (over-drying, extra heat exposure)
• Inconsistent dry results between similar loads

Quick checks before replacing parts

Try these steps first (power off the dryer before any internal access):

• Wipe the two metal strips with rubbing alcohol to remove dryer sheet residue
• Avoid using excessive fabric softener sheets, which can coat the sensor
• Clean the lint screen and confirm strong airflow at the exhaust
• Test with a similar-size load on an Auto Dry cycle after cleaning

Common related parts (if symptoms continue)

If Auto Dry performance is still inconsistent after cleaning, these parts are commonly involved in drying performance on this model family:

Symptom	Common area to check	Example part on this model page
Runs but dries poorly	Air movement	Dryer blower wheel WP697772
Over-dries or under-dries in Auto	Sensor circuit	Dryer moisture sensor WP3387223
Long dry times, heat issues	Temperature sensing	Dryer thermistor WP8577274

Last updated: January 2026