Frigidaire AGQ8000FS2 dryer Parts

Yes. For your Frigidaire dryer model AGQ8000FS2, looking up parts by the full model number is the most reliable way to match the correct replacement part because it filters results to components that fit your exact dryer configuration.

How to find the model number on the dryer

We recommend using the model number from the dryer’s data tag (not the number on a receipt). Common locations include:

• Inside the dryer door opening on the cabinet frame
• On the door itself (edge or inner panel)
• On the rear panel of the dryer
• Near the lower front access area (varies by design)

For model-specific identification tips and diagrams, use the AGQ8000FS2 owner’s manual.

How to search parts once you have the model number

When you search by AGQ8000FS2, you can narrow parts by symptom or by section (drum, door, controls, heat system). This helps you avoid ordering a similar-looking part that does not fit.

• Enter the full model number exactly as shown on the tag
• Match the part by name and ID, not just by appearance
• Compare your symptom to common wear items (belt, bearing, thermistor)
• Confirm gas vs. electric details before ordering (this model family can have variations)
• Use the exploded-view style listings to verify where the part installs

Examples of common AGQ8000FS2 parts customers replace

These are typical wear or failure items for many Frigidaire dryers:

Symptom	Common part type	Example part for this model
Drum not turning	Drum belt	Frigidaire dryer drum belt 134503600
Squealing or rumbling	Drum bearing components	Dryer drum bearing kit, drum bearing, glides
Overheating or no heat events	Temperature safety/control	Thermal limiter, thermistor

Why it matters

Dryer parts often look interchangeable, but small differences (mounting points, wiring connectors, drum size, gas valve setup) can cause poor fit or unsafe operation. Searching by AGQ8000FS2 keeps the match tight and reduces returns.

Last updated: February 2026

For the Frigidaire AGQ8000FS2 dryer, a replacement electronic control board typically costs about $150 to $250, depending on the exact board version and availability. Pricing can vary by supplier and whether the board is new or refurbished; confirm the correct part by matching your model and wiring layout in the AGQ8000FS2 owner’s manual.

What affects the price (and what to check first)

Before buying a board, we recommend ruling out common issues that can mimic a bad control.

• Verify the dryer has the correct power supply and is properly grounded.
• Check for loose or damaged wire connections at the control and harness.
• Look for heat-related failures that can trigger shutdowns (restricted venting, overheating).
• If the dryer is gas and the burner shuts off, follow the restart timing guidance in the installation instructions.
• If the dryer shows an error, use the Frigidaire dryer error codes reference to narrow the failure.

Quick comparison: control board vs. other common fixes

Sometimes a lower-cost part solves the symptom (no heat, stops mid-cycle, won’t start) without replacing the board.

Symptom	Often caused by	Example part for AGQ8000FS2
Runs but no heat (gas)	Ignition or gas valve coil issue	Coil-seconda 5303931775
Overheats or shuts down	Airflow restriction or safety limit open	Thermal limiter 137032600
Long dry times	Low voltage (208V), vent restriction, sensor issue	Dryer thermistor 134587700

Why it matters

Control boards are one of the higher-cost dryer parts, and misdiagnosis is common. Confirming power, wiring integrity, airflow, and any stored error codes helps ensure you replace the right component the first time.

Last updated: February 2026

Yes. Frigidaire dryers, including the Frigidaire AGQ8000FS2, are a solid choice for dependable everyday drying, straightforward controls, and widely available replacement parts. Long-term satisfaction still depends on correct installation, safe venting, and routine lint and exhaust maintenance.

What “good” means for a dryer brand

A dryer brand is “good” when it delivers consistent heat and airflow, runs smoothly, and is serviceable over time. For AGQ8000FS2 owners, that comes down to a few practical factors:

• Proper gas supply setup and safe exhaust routing
• Stable drum support (bearings, glides, felt seals)
• Reliable temperature sensing and overheat protection
• Easy access to common wear parts when repairs are needed

For model-specific operating and safety guidance, use the AGQ8000FS2 owner's manual.

What to maintain to keep performance high

Most “dryer problems” are airflow or wear-item issues, not the brand itself. We recommend:

• Clean the lint screen before every load
• Inspect and clean the exhaust duct regularly (crushed or long ducts slow drying)
• Avoid overloading; it strains the drum belt and idler
• Watch for scraping, thumping, or squealing; those point to drum support wear
• If heat becomes inconsistent, check airflow first, then heating system components

Common wear parts you can replace

If your AGQ8000FS2 starts squealing, thumping, or the drum stops turning, these are common fixes:

Symptom	Likely area	Example part for this model
Drum not turning	Belt/idler	Frigidaire dryer drum belt 134503600
Squealing or rumbling	Drum support	Dryer drum bearing kit, drum bearing, drum glide
Overheating or no heat (gas)	Safety/heat sensing	Thermal limiter, thermistor, igniter, valve coils

Why it matters

A Frigidaire dryer can perform extremely well for years, but only if airflow and temperature control stay in spec. Good venting and clean lint paths reduce dry times, protect the burner system, and prevent repeated thermal limiter trips.

For correct placement, rough-in dimensions, gas supply requirements, and exhaust system requirements, follow the AGQ8000FS2 installation guide.

Last updated: February 2026