Craftsman 358352162 chainsaw Parts

On the Craftsman 358352162 gas chainsaw, the serial number is typically on a sticker or stamped plate near the oil fill cap or on the bar side of the saw under the handle. Once you find it, record it exactly as shown for parts lookup and service records.

Where to check on the saw

Look in these common spots first:

• Near the oil fill cap (often on the rear handle or tank housing)
• Bar side of the saw under the handle (near the clutch cover area)
• On the main chassis/crankcase area (stamped into the housing on some units)
• On a label near the starter/recoil cover

If the label is dirty, wipe it with a dry rag so you do not smear the print.

How to use the serial number (and what to write down)

For the most accurate lookup, we recommend writing down:

• Model number: 358352162
• Serial number: copy all letters and numbers in order
• Any prefix/suffix on the serial tag (do not omit dashes)
• Date code (if shown)

Serial number vs. model number

Item	What it identifies	Where you use it
Model number (358352162)	The chainsaw design family	Selecting the correct parts diagrams and lists
Serial number	Your exact production unit	Confirming production run details and service history

Why it matters

Craftsman chainsaws can have small production changes across serial ranges. Having the serial number helps match the correct parts and avoids ordering the wrong fuel line, carburetor kit, or clutch components.

For additional identification and safety details, use the owner's manual.

Last updated: February 2026

Your Craftsman chainsaw’s model is printed on a model number label on the saw. For this unit, the operator’s manual identifies it as model 358.352162 (often shown as 358352162) and describes it as a 36cc, 16-inch bar gas chainsaw. See the 358352162 owner's manual for label location and identification details.

Where to look for the model number label

We recommend checking these common spots on Craftsman gas chainsaws like model 358352162:

• On the starter housing (recoil starter side)
• Near the rear handle or trigger handle area
• On the crankcase or chassis near the bar mount
• Under the top cover near the air filter area
• On the underside of the saw body (less common)

What numbers matter (and what they mean)

Use the model number first; it is the best match for parts diagrams and the correct parts list.

What you find on the saw	Example	What to do with it
Model number	358.352162 or 358352162	Use this to look up parts and the manual
Engine size / description	36cc, 2-cycle	Helps confirm you have the right family of saw
Bar length	16 in.	Helps match bar and chain specs

If the label is hard to read

If the label is worn, you can still confirm the saw by matching key specs from the manual and the parts list.

• Clean the label area with a dry rag (avoid solvents on decals)
• Use a flashlight at an angle to make faded printing stand out
• Take a close-up photo and zoom in
• Compare your saw’s bar length and layout to the manual’s diagrams

Why it matters

The correct model number ensures you get parts that fit, such as the right fuel line size, air filter, carburetor kit, chain, and bar. It also helps you follow the correct fuel mix and maintenance steps for safe, reliable starting and cutting.

Last updated: February 2026

Common problems on the Craftsman 358352162 gas chainsaw include hard starting, rough running, poor acceleration or power under load, excessive smoking, overheating, and chain issues like clattering, cutting at an angle, or moving at idle. Many of these trace back to fuel delivery, air flow, carburetor settings, or chain tension and sharpness (see the owner's manual).

Quick symptom checklist (most common)

• Won’t start or only runs a few seconds: empty tank, flooded engine, spark issue, or fuel not reaching the carburetor
• Won’t idle smoothly: idle speed or carburetor adjustment
• Dies under load or lacks power: dirty air filter, fouled plug, plugged muffler/spark arrestor screen, or carburetor adjustment
• Smokes excessively: choke partially on or incorrect fuel mixture
• Runs hot: dirty air filter, high-speed mixture too lean, or crankcase leak
• Chain problems: incorrect tension, dull/damaged cutters, worn sprocket, bent/burred bar, or clutch issues

What to check first (fast, high-impact steps)

1. Fuel and mix: Use fresh fuel with the correct gasoline-to-oil ratio; don’t store gas from one season to the next.
2. Air filter: A clogged filter can make the saw run rich and lose power; replace the engine air filter 530037793 if it’s dirty or damaged.
3. Fuel lines and primer: Cracked or loose lines cause hard starting and stalling; inspect and replace as needed using the poulan lawn & garden equipment fuel line, small 530069247 and/or ayp lawn & garden equipment fuel line, large 530069216.
4. Carburetor condition: If fuel delivery is weak or tuning won’t hold, a rebuild or replacement is common; see how to rebuild a chainsaw carburetor.
5. Chain tension and sharpness: A loose or dull chain increases kickback risk and cuts poorly; tension and sharpen per the manual.

Common causes and likely fixes

Symptom	Likely cause	Typical fix
Won’t start	Flooded, no spark, fuel not reaching carb	Correct starting procedure, check plug, inspect fuel lines/primer
Runs rough	Dirty air filter, carb out of adjustment	Clean/replace filter; adjust carb
Chain moves at idle	Idle speed too high or clutch issue	Adjust idle; inspect clutch
Cuts at an angle	Dull/uneven cutters, worn/bent bar	Sharpen evenly; replace bar if worn

Why it matters

Ignoring basic maintenance (fresh fuel, clean air filter, correct chain tension) can create bigger problems like fouled plugs, plugged exhaust screens, poor cutting performance, and increased kickback risk.

Last updated: February 2026

For the Craftsman 358352162 gas chainsaw, use a 40:1 fuel-to-oil mix. That is the specified ratio for this engine when using unleaded gasoline mixed with a good-quality 2-cycle air-cooled engine oil; it helps protect the engine with the correct lubrication level (see the owner's manual).

Correct mix for this model

Use this ratio every time you mix fuel:

• 40:1 mix ratio
• 3.2 fl oz of 2-cycle oil per 1 gallon of unleaded gasoline
• Use 2-cycle air-cooled engine oil (not automotive oil or marine/boat oil)
• Mix in an approved fuel container; add oil, then gasoline, then shake briefly
• Refuel outdoors and wipe up spills before starting

Quick mixing table (40:1)

Gasoline amount	2-cycle oil to add
1 gallon	3.2 fl oz
1/2 gallon	1.6 fl oz
1 quart	0.8 fl oz

What happens if you run 50:1 in a 40:1 saw?

A 50:1 mix contains less oil than 40:1. In a saw designed for 40:1, that reduces lubrication and increases heat and wear risk during cutting, especially under heavy load.

Related maintenance that affects fuel performance

Fuel ratio is only one part of a good-running saw. If your 358352162 is hard to start, runs rough, or won’t idle, these items commonly matter just as much:

• Clean or replace the air filter (example: engine air filter 530037793)
• Inspect fuel lines for cracks, soft spots, or leaks (example: fuel line, small 530069247)
• Check the primer bulb for damage (example: primer assembly 530071835)
• Keep fresh fuel mix; don’t store mixed fuel for long periods
• Replace the spark plug yearly as part of routine service

Why it matters

Two-cycle engines rely on the oil in the fuel for crankshaft, piston, and cylinder lubrication. Using the specified 40:1 mix helps the Craftsman 358352162 maintain the correct air-fuel mixture, cooling, and long-term engine life.

Last updated: February 2026

The model number for this Craftsman gas chainsaw is 358.352162 (often written without the dot as 358352162). You can confirm it on the model/serial tag and in the owner's manual, which lists it as a 2.2 cu. in./36cc 2-cycle chainsaw with a 16-inch bar.

Where to find the model number on the saw

We recommend checking the model tag first, then matching it to the manual.

• Look for a model/serial label on the saw body (commonly near the rear handle, starter housing, or fuel tank area)
• Match the full model format: 358.352162
• Write the number down before ordering parts or using diagrams
• Clean the label gently if it is oily or dusty so the digits are readable

Why the dot matters (358.352162 vs 358352162)

Both formats refer to the same model; the dot is a formatting style used on some labels and manuals.

You might see it as	What it means	Where it shows up
358.352162	Same model number	Operator's manual and some labels
358352162	Same model number	Parts lookup and search

Why it matters when buying parts

Using the exact model number helps us match the correct illustrated parts list, especially for fuel and engine items.

Common parts customers replace on this model include:

• Fuel line, small 530069247
• Engine air filter 530037793
• Chain brake assembly 530029850

Why it matters

A single digit difference in a Craftsman 358.xxxxxx model can change the bar/chain fit, fuel line routing, and carburetor parts; confirming 358.352162 prevents wrong-part returns.

Last updated: February 2026