Kenmore 10655249400 side-by-side refrigerator Parts

Most Kenmore side-by-side refrigerators are about 32 to 36 inches wide; for your specific Kenmore model 10655249400, the exact cabinet width is listed in the 10655249400 owner's manual.

Side-by-side refrigerator width is usually driven by capacity and whether the unit is standard-depth or counter-depth.

• Standard-depth models commonly run 33 in. to 36 in. wide
• Counter-depth models are often 32 in. to 36 in. wide (depth changes more than width)
• Door style and handles can add extra clearance needs beyond cabinet width
• Door swing needs space next to walls so bins can clear
• Water line hookup (if you have an ice maker) needs room behind the unit

We recommend measuring both the cabinet and the “installed” width so you do not get surprised during delivery.

A refrigerator that is even 1 inch too wide can prevent proper installation, reduce door opening range, and make it harder to service parts like the ice maker or water inlet valve.

In the use and care information for this Kenmore side-by-side style, proper ventilation clearance is called out; we follow those spacing guidelines when planning an opening and door swing. See the 10655249400 owner's manual for the recommended clearances.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10655249400, the model number is printed on the model and serial number label located on the inside wall of the fresh food (refrigerator) compartment; check the interior side wall near the front where it is easy to read. See the 10655249400 owner's manual for the exact label location illustration.

• Open the refrigerator (fresh food) door and look along the inside side walls
• Check near the front edge of the cabinet liner (not the door)
• Use a flashlight; labels can be low-contrast or partially covered by shelves
• Look for a combined model and serial label (both are typically on the same sticker)
• Write the model number down exactly as shown before ordering parts

The label usually includes both identifiers; we recommend recording both before troubleshooting or ordering Kenmore parts.

Kenmore 106 model refrigerators can have multiple design revisions. Using the exact model number from the inside-compartment label helps us match the correct parts (such as an ice maker assembly, water inlet valve, or door cam) and avoid returns due to fit issues.

Last updated: February 2026

Your Kenmore 10655249400 side-by-side refrigerator ice maker usually stops making ice because it is turned off (wire shutoff arm up), the freezer is not cold enough yet, or the water supply to the refrigerator is off or restricted. Start by confirming the ice maker is ON and the water valve is open.

• Make sure the wire shutoff arm is down (ON); do not force it up or down.
• If the ice maker was just installed or the refrigerator was recently moved, wait 72 hours for full ice production.
• Confirm the household water shutoff valve to the refrigerator is fully open.
• Check for a kinked or pinched water line behind the refrigerator.
• Look for an ice cube jammed in the ejector area; clear it with a plastic utensil.
• Verify the freezer control is set cold enough; wait 24 hours after any adjustment.

The ice maker should produce about 7 to 9 batches in 24 hours under normal conditions. After first startup, we recommend discarding the first three batches.

If the basic checks pass (ice maker ON, freezer cold, water on) and you still have no ice, these parts are common causes:

• Refrigerator water inlet valve W10408179 (won’t fill the ice mold if it fails)
• Ice maker assembly 4317943 (internal motor/module issues)
• Refrigerator water filter housing WP2186443 (leaks or restriction at the filter head)

An ice maker depends on two things: cold freezer temperatures and steady water flow. If either is missing, the ice mold will not fill or the harvest cycle will stall, so production drops to zero.

For model-specific operating details (wire shutoff arm operation, expected output, and water supply notes), follow the steps in the 10655249400 owner's manual.

Last updated: February 2026

Kenmore model numbers tell us who built the appliance and which design family it belongs to. On Kenmore refrigerator model 10655249400, the 106 prefix identifies the manufacturer family, and the remaining digits narrow down the exact configuration so we can match the correct parts and manual.

For Kenmore 10655249400, the model and serial number label is typically located on the inside wall of the refrigerator compartment. Confirm the exact location and label details in the 10655249400 owner's manual.

• Open the fresh food (refrigerator) door and look along the inside side walls
• Check near the crisper area and the upper liner walls
• Write down the full model number and serial number exactly as shown
• Keep the purchase date with your records for service and parts matching

Kenmore model numbers are usually a prefix + base model + suffix.

• Prefix (first 3 digits): identifies the manufacturer family (for example, 106)
• Middle digits: identify the platform or base design
• Ending digits: identify feature and production variations (color, dispenser style, revisions)

Using the full model number prevents ordering the wrong refrigerator water inlet valve, thermostat, ice maker assembly, door gasket, or shelf parts. Even small suffix differences can change wiring harnesses, dispenser components, and door hardware.

If you are diagnosing dispenser or ice issues, the Kenmore 106 model refrigerator error codes guide is a fast way to interpret display or diagnostic codes before replacing parts.

Last updated: February 2026

The most common problems we see on Kenmore refrigerators like model 10655249400 are cooling issues, water leaks, ice maker and dispenser troubles, moisture buildup, and door sealing problems. Many of these come down to airflow being blocked, controls needing a reset, or worn parts such as gaskets, valves, or defrost components (see the 10655249400 owner's manual).

• Not cooling or warm temperatures: blocked air vents, frequent door openings, controls set incorrectly, or a control reset needed.
• Moisture buildup inside: high room humidity, doors opened often, food not wrapped well, or vents blocked.
• Water leaking or puddles: clogged defrost drain, loose water line connections, or a leaking valve.
• Ice maker not making ice: water supply issue, failed ice maker, or a valve problem.
• Doors hard to open or not sealing: dirty or sticky gaskets, cabinet not level, or door alignment issues.
• Noises: fan blade rubbing ice, airflow restrictions, or normal compressor/fan cycling.

1. Make sure air vents are not blocked by food packages.
2. Confirm the temperature controls match room conditions; for digital controls, turn the unit OFF then ON to reset.
3. Reduce warm-ups by opening doors less often and loading groceries efficiently.
4. Clean and dry door gaskets if they feel sticky.
5. If the refrigerator wobbles, level it so doors seal consistently.

Cooling, moisture, and ice maker problems often share the same root cause: restricted airflow or inconsistent temperatures. Fixing vent blockage, door sealing, and water supply issues early helps protect food quality and reduces strain on the compressor.

Last updated: February 2026

Most Kenmore refrigerators last 10 to 15 years on average. For a Kenmore side-by-side like model 10655249400, consistent care (cleaning, good door sealing, and fixing cooling or water issues early) is what most often determines whether it reaches the high end of that range.

A refrigerator’s life is usually driven by how hard the sealed cooling system and airflow components have to work day to day.

• Condenser coil cleanliness (dirty coils raise compressor run time)
• Door gasket condition (air leaks cause longer run times and frost)
• Stable temperatures (freezer near 0°F, fresh food near 37°F)
• Water/ice system health (leaks and clogs create secondary problems)
• Ventilation and leveling (poor airflow and misalignment stress parts)

For model-specific care and cleaning intervals, follow the 10655249400 owner's manual.

• Vacuum condenser coils and the grille area regularly.
• Keep door gaskets clean and fully sealing.
• Do not block interior air vents with food packages.
• Replace clogged water filters on schedule.
• Address slow ice production, warm temps, or unusual noises quickly.

If you’re troubleshooting water supply problems that shorten lifespan, the refrigerator water inlet valve W10408179 is a common wear item on many Kenmore 106-style designs.

A refrigerator that runs longer to maintain temperature uses more energy and wears out key components faster. Simple upkeep like cleaning and sealing reduces run time, helps food stay safer, and extends the service life.

Last updated: February 2026

To replace the ice maker in your Kenmore side-by-side refrigerator model 10655249400, we disconnect power, shut off the water supply, swap the ice maker assembly, then restore power and water and turn the ice maker back on using the wire shutoff arm. See the 10655249400 owner's manual for model-specific access and fastener locations.

• Unplug the refrigerator (or switch off the breaker) before servicing.
• Turn off the main water supply to the refrigerator.
• Empty the ice bin and clear any loose cubes.
• Protect the freezer floor with a towel to catch melting ice.
• Use a grounded 3-prong outlet when restoring power (no adapters or extension cords).

1. Turn the ice maker off: lift the wire shutoff arm to the OFF (up) position.
2. Remove the ice bin to access the ice maker area.
3. Disconnect power to the refrigerator.
4. Remove the ice maker mounting screws and gently pull the ice maker forward.
5. Unplug the ice maker wiring harness (do not pull on wires).
6. Install the replacement by reconnecting the harness, positioning the ice maker, and tightening mounting screws.
7. Restore water and power, then lower the wire shutoff arm to turn the ice maker on.

A correct ice maker replacement prevents leaks, protects wiring, and restores normal ice production (many units make multiple batches per day when operating correctly). Following the shutoff steps also helps avoid water spurts and air in the line after service.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10655249400, a bad compressor usually shows up as poor cooling with the unit running a lot, unusual compressor noises (or no compressor sound at all), and a compressor shell that gets very hot while the temperatures stay warm. Use the 10655249400 owner's manual to compare normal operating sounds versus problem symptoms.

• Confirm the refrigerator and freezer controls are set correctly (avoid extreme settings).
• Listen for normal sounds: a high-pitched or pulsating compressor sound can be normal on efficient units.
• Check airflow: make sure vents inside the compartments are not blocked by food.
• Verify the condenser area is clean and the unit has breathing room (dust buildup can mimic compressor trouble).
• If you have an ice maker, note that a buzzing sound can simply be the water valve filling the ice maker.

A compressor is more likely at fault when these happen together:

• Refrigerator runs constantly but both sections stay warm.
• Repeated clicking every few minutes (start attempt then shutoff).
• Compressor is extremely hot to the touch after trying to run.
• No steady “hum” from the compressor even though fans may run.

Before replacing a compressor, we typically rule out common cooling and start-up causes:

• Temperature control issues (for this model, see refrigerator thermostat WP2198202).
• Defrost system problems that cause heavy frost and weak airflow (example: refrigerator defrost bi-metal WPW10225581).
• Sealed system or refrigerant flow issues (often requires a sealed-system technician).

Compressors are part of the sealed refrigeration system; misdiagnosing the problem can lead to an expensive repair that does not restore cooling. Checking for normal sounds, airflow restrictions, and defrost symptoms helps pinpoint the real failure faster.

Last updated: February 2026

The cubic-foot capacity for Kenmore side-by-side refrigerator model 10655249400 is listed in the product specifications section of the 10655249400 owner's manual. That published spec is the correct total interior volume for the fresh food and freezer compartments combined.

Look for headings such as “Product specifications,” “Capacity,” “Features,” or “Refrigerator information.” Capacity is usually shown as total cubic feet.

• Check the first few pages and the specifications/features section
• Search within the PDF for: capacity, cu. ft., cubic, or volume
• If your unit has an ice maker installed, note that usable freezer space is lower than total volume
• If you are comparing models, use total capacity for apples-to-apples comparisons

Total cubic feet is a standardized measurement; usable space depends on shelves, bins, and accessories.

Capacity helps you compare replacement refrigerators, plan grocery storage, and understand how features like an ice maker affect day-to-day space.

Last updated: February 2026