GE DDT595SMJ0ES dishwasher Parts

Your GE dishwasher’s model number is printed on the rating label inside the door area. For GE DDT595SMJ0ES units, the DDT595SMJ0ES owner’s manual notes you can find the model and serial numbers on the tub wall just inside the door.

Check these common label locations first (use a flashlight and wipe off any moisture or soap film):

• Tub wall just inside the door opening (most common for GE)
• Left or right inner frame around the door opening
• Top edge of the door (visible when the door is open)
• Side edge of the door itself
• Underside of the control panel lip (less common)

Record both numbers exactly as shown:

• Model number: identifies the exact design and parts list
• Serial number: helps match production changes and correct replacement parts

• Shine light across the label from the side to make faint print stand out
• Take a close-up photo and zoom in
• Copy characters carefully (0 vs O, 1 vs I)

Using the exact model number (like DDT595SMJ0ES) prevents ordering the wrong GE dishwasher parts such as a control board, door latch, or spray arm.

Last updated: January 2026

Yes. On the GE DDT595SMJ0ES dishwasher, an FTD (fail to drain) condition commonly happens when water cannot leave the tub due to a clog in the drain path (air gap, disposer connection, filter area, or drain hose). See the DDT595SMJ0ES owner’s manual for drain and air gap cleaning steps.

• Cancel the cycle and let the unit attempt to drain.
• Check for standing water in the bottom of the tub.
• If you have an air gap, remove the cover and clean the cap and opening.
• If the dishwasher drains into a garbage disposer, run the disposer to clear it.
• Confirm the kitchen sink drains normally; a slow sink often points to a plumbing restriction.
• Inspect the drain hose routing for a proper high loop or air gap (routing issues can mimic a clog).

If the drain path is clear but the dishwasher still will not pump out, the drain pump can be the issue. For this model, the replacement is the dishwasher drain pump WD19X25187.

• Hums but no draining: pump jam or blockage at the impeller
• No pump sound at all: electrical issue, control issue, or failed pump
• Intermittent draining: partial clog, hose routing problem, or weak pump

An FTD condition leaves dirty water in the tub, can cause odors, and can stop the cycle from completing. Clearing the drain path (especially the air gap or disposer connection) restores normal draining in many cases.

Last updated: January 2026

For the GE DDT595SMJ0ES dishwasher, the most common issues we see are draining problems (clogged filter or drain path), the dishwasher not starting (door not fully latched or control issue), and poor cleaning from restricted spray-arm flow. These problems usually trace back to food debris buildup or a failed component.

• Won’t drain or has standing water: drain filter, drain hose routing, or drain pump restriction
• Won’t start or stops mid-cycle: door not fully latched, UI/control problem, or power interruption
• Not cleaning well: clogged spray arm holes, blocked detergent cup, or circulation issue
• Not drying well: heater-related issue, rinse aid issue, or cycle selection
• Leaks: door seal/tub gasket wear, door not closing squarely, or oversudsing

1. Remove and rinse the filter area; clear any food, labels, or glass.
2. Confirm the door closes firmly; a weak latch can prevent a cycle from starting.
3. Check that dishes are not blocking the detergent dispenser (this is a common cause of detergent left in the cup).
4. Run hot water at the sink before starting a cycle so the dishwasher fills with hotter water.
5. Use only automatic dishwasher detergent; hand soap causes heavy suds and can trigger drain and leak symptoms.

Drain clogs and spray restrictions reduce wash pressure and can leave detergent undissolved, while a weak door latch can make the dishwasher act “dead” even when it has power. Catching these early helps prevent repeat cycles, odors, and water left in the tub.

For model-specific operating and care steps (including loading guidance and cleaning recommendations), use the DDT595SMJ0ES owner's manual.

Last updated: January 2026

To clear an error code on your GE DDT595SMJ0ES dishwasher, we start by canceling the current cycle: press and hold Start for 3 seconds, then close the door so the unit drains and resets. After it drains, start a fresh cycle to see if the code returns (see the DDT595SMJ0ES owner's manual).

• Cancel and drain (first step): Press and hold Start for 3 seconds, then close the door so the dishwasher drains.
• Restart correctly: Press Start and close the door within 4 seconds to begin a new cycle.
• Power reset (if the code comes back): Turn the dishwasher’s power off at the breaker for about 5 to 10 minutes, then restore power and try a cycle.
• Check the door: If the door is not fully closed, the dishwasher can pause and beep; closing the door and pressing Start can clear the condition.
• Address common “false” triggers: If the dishwasher will not fill, check that the water valve under the sink is on and that the flood float is not stuck.

If the same error returns right away after a cancel/drain and power reset, we treat it as an active fault (not a “stored” code). These are the most common next checks:

• Clean filters and confirm spray arms spin freely
• Verify the unit fills and circulates water normally
• Look for pinched/kinked drain hose routing
• If symptoms point to control issues, inspect connections to the dishwasher electronic control board WD21X24901C

Clearing the code resets the cycle logic, but repeating codes usually indicate a real problem (door latch, fill, drain, leak detection, or control). Fixing the cause prevents mid-cycle stops, poor cleaning, and repeat beeping.

For code definitions and model-family troubleshooting, use our GE electronic dishwasher error codes reference alongside your manual.

Last updated: January 2026