Kenmore Elite 11097731701 dryer Parts

On your Kenmore Elite dryer model 11097731701, the model number is on the model and serial number label attached to the dryer cabinet; you’ll typically see it when you open the door and look around the door opening area. For the exact label location and what it looks like, use the owner's manual.

• Open the dryer door and inspect the cabinet frame around the door opening.
• Check the top edge and side edges of the door opening.
• Look for a sticker or metal plate that lists model and serial.
• If the label is dusty, wipe it gently so the numbers are readable.
• Record the full model number and serial number for parts lookup and service.

The model and serial number label is meant for product records and service. It commonly shows:

• Model number (for this dryer: 11097731701)
• Serial number
• Gas and electrical rating information
• Sometimes the BTU rating and other specifications

The model number is how we match the correct Kenmore Elite dryer parts and diagrams to your exact build. Even small model number differences can change which parts fit (for example, a drum support roller, idler pulley, or thermistor).

To order replacement parts for model 11097731701, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

Common problems on the Kenmore Elite dryer model 11097731701 include not starting, no heat or long dry times, loud thumping or squealing, and airflow or venting faults. Most issues trace back to power supply, door-latch/start input, lint restriction, or normal wear parts in the drum drive system.

• Dryer will not run: tripped breaker or blown fuse, door not fully latched, Start button not held long enough
• No heat (drum turns but clothes stay damp): one leg of power missing (electric supply issue), gas supply valve closed (gas models), failed heat-sensing or safety parts
• Long dry times: clogged lint screen, blocked or crushed venting, lint buildup inside the cabinet or ducting
• Loud noise or thumping: worn drum rollers, idler pulley, or blower wheel
• Burning smell on first use after install: brief “new heat” odor that fades after initial heating

1. Confirm the dryer is plugged into a grounded outlet and power is on.
2. Check the house fuse/circuit breaker; reset if tripped.
3. Close the door firmly; if it does not latch, the control can beep and the cycle will not start.
4. Press and hold Start for 2 to 5 seconds (large loads often need a longer press).
5. Clean the lint screen and make sure the vent is not blocked.

If your 11097731701 runs but squeals, thumps, or struggles to turn, these wear items are frequent fixes:

A restricted vent or lint buildup can cause overheating, shutdowns, and long dry times. Worn rollers, an idler pulley, or a blower wheel can quickly turn a minor noise into a no-tumble failure.

For operating checks, cleaning guidance (lint screen, interior, accumulated lint), and troubleshooting steps for “will not run” and “no heat,” use the 11097731701 owner's manual.

You can also search additional Kenmore parts by model number on Sears PartsDirect.

Last updated: February 2026

If your Kenmore Elite dryer 11097731701 will not start, or it runs but produces no heat on heated cycles, a blown thermal fuse or thermal cut-off is a top suspect. Confirm it with a multimeter continuity test after unplugging the dryer; see the owner's manual for access guidance.

• Dryer will not run at all (no motor)
• Drum turns but there is no heat
• Heat cuts out mid-cycle, then returns after cooling
• Long dry times before the failure (restricted airflow)
• Dryer cabinet or laundry area feels hotter than normal

1. Unplug the dryer or switch off the breaker.
2. Remove the appropriate panel to reach the fuse/cut-off.
3. Pull at least one wire off the fuse terminal.
4. Set the meter to continuity or lowest ohms.
5. Probe the two terminals.

Replace the failed safety device and correct the overheating cause. A common related replacement for this dryer is the dryer thermal cut-off kit WP8573713.

• Clean the lint screen and housing
• Clear lint from the lint duct and blower area
• Inspect the vent hose for kinks, crushing, or long runs
• Make sure the outside vent hood opens fully
• Run a timed heated cycle and confirm strong airflow outside

Thermal fuses and thermal cut-offs open to stop overheating. If the vent system stays restricted, the replacement part can open again and the dryer can return to no-heat or no-start symptoms.

You can order parts for model 11097731701 from the parts list for this dryer, or search by model on Sears PartsDirect.

Last updated: February 2026

To open the front panel on your Kenmore Elite dryer model 11097731701, unplug the dryer first, then remove the top so you can reach the screws and clips that hold the front panel. Use the handling and safety steps in the 11097731701 owner's manual.

• Unplug the dryer or switch off the breaker.
• If your 11097731701 is gas, close the gas shutoff valve.
• Protect the floor with cardboard if you need to move or tilt the dryer.
• Keep screws organized so reassembly is straightforward.

1. Remove the screws at the back edge of the top panel.
2. Slide the top panel back, then lift it off.
3. Remove the screws securing the front panel at the upper inside corners.
4. Disconnect the door switch wire harness if it is attached to the front panel.
5. Lift the front panel up to unhook the lower tabs, then pull it forward and set it aside.

• Check for hidden screws near the lint screen housing or console brackets.
• Make sure the door switch connector is fully unplugged and not snagged.
• Lift the panel higher to clear the lower retaining tabs before pulling forward.

Removing the front panel correctly prevents broken tabs, pinched wiring, and cabinet air leaks that can cause long dry times and overheating.

If you need to order parts, use the parts list for model 11097731701 or search by model on Sears PartsDirect.

Last updated: February 2026