Kenmore 1069552811 refrigerator Parts

For your Kenmore side-by-side refrigerator model 1069552811, set the freezer to 0°F (-18°C) for everyday use. That temperature keeps frozen food safely stored while helping the refrigerator run efficiently; fine-tune only if items are too soft or you see excess frost (use the control guidance in the 1069552811 owner's manual).

Most temperature complaints come from control settings and airflow balance, not a “bad freezer.” Your model uses a Thermostat control (overall colder or warmer) and an Air balance control (sends more cold air to the freezer or fresh food section).

• Start with the freezer at 0°F and the refrigerator at 37°F.
• If the freezer is warm, move the Thermostat one step colder and wait 24 hours before changing again.
• If the freezer is warm but the refrigerator is too cold, shift the Air balance toward the freezer.
• Keep vents clear; blocked vents cause warm spots and poor ice production.
• Avoid setting colder than needed; it can increase frost and energy use.

• Confirm the door closes and seals fully; gaps pull in humid air and create frost.
• Let temperatures stabilize for 24 hours after any adjustment.
• Do not overload the freezer; air must circulate around packages.
• Clean condenser coils regularly for better cooling performance.
• Check that the refrigerator is level; misalignment can prevent proper sealing.

Keeping the freezer at 0°F protects food quality and helps your Kenmore 1069552811 maintain stable temperatures without running excessively. Stable temps also support consistent ice maker performance.

If you are also seeing ice maker issues, the ice maker assembly - refrigerator ice maker by whirlpool 4317943 is a common replacement when the unit stops producing ice after temperature and water supply checks.

You can order replacement parts for model 1069552811 from the parts list for this refrigerator, or search by model number on Sears PartsDirect.

Last updated: February 2026

Most Kenmore side-by-side refrigerators are about 32 to 36 inches wide; your Kenmore 1069552811 is typically in that same range. For the exact cabinet width and the clearance you need for doors and ventilation, use the dimensions and spacing guidance in the 1069552811 owner's manual.

Side-by-side refrigerator widths commonly fall into these buckets:

• 32 to 33 inches: narrower, smaller-capacity models
• 35 to 36 inches: most full-size side-by-sides
• 36+ inches: larger or specialty configurations

To get a number you can trust, we recommend measuring in three places:

• Cabinet width: left edge to right edge of the main box (not the doors)
• Overall width: include handles if they stick out past the doors
• Installation width: cabinet width plus the side clearances needed for airflow

If you are replacing an older unit, also measure the door swing path so the doors can open fully without hitting a wall or cabinet.

Even if the cabinet is a certain width, the opening must allow ventilation. The manual guidance for this model family calls for:

• 1/2-inch minimum space on each side
• 1/2-inch minimum space at the top
• Extra space at the back if you have an ice maker or water dispenser (for the water line connection)

Width is not just about fitting the box into the opening; it also affects door alignment, gasket sealing, and airflow. Tight clearances can lead to warm temperatures, frost buildup, or moisture issues over time.

If you are planning a refresh while you measure, common fit-related replacements for this model include door storage and sealing parts such as the refrigerator door bin WP2156022 and the refrigerator door gasket (black) 2159081. You can also search by model number on Sears PartsDirect if you need additional options.

Last updated: February 2026

To clean the condenser coils on your Kenmore 1069552811 side-by-side refrigerator, remove the base grille, vacuum the coils when they are dusty or dirty (as often as every other month), then reinstall the grille. This restores airflow and helps the refrigerator run efficiently; see the 1069552811 owner's manual.

• Unplug the refrigerator (safety first).
• Open both doors.
• Remove the base grille (it snaps in and out).
• Vacuum the condenser coils and the area around them using a brush attachment.
• Reinstall the base grille and confirm it snaps fully into place.
• Plug the refrigerator back in and verify normal operation.

The base grille must come off to access the condenser coils and defrost pan.

• Clean coils whenever you see dust buildup; many homes need it about every other month.
• Use a coil brush or soft brush attachment to avoid bending fins.
• Keep the base grille clear of rugs, pet hair, and storage items so air can circulate.
• While you are there, check door gaskets for a tight seal; leveling helps the doors seal correctly.

Dirty condenser coils reduce heat transfer, which makes the compressor and fans run longer. Regular coil cleaning improves cooling performance, reduces energy use, and can help prevent warm refrigerator temperatures.

If you need replacement parts while servicing the lower front area, we stock model-matched items such as the refrigerator bulb WP22002263 and other Kenmore 1069552811 parts on this page, or you can search by model at Sears PartsDirect.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 1069552811, the model and serial number are on the model and serial label located on the inside side wall of the fresh food (refrigerator) compartment. Use that label to record the complete model and serial number for parts lookup and service.

• Open the refrigerator (fresh food) door.
• Look along the inside side wall for a printed label.
• Check near the control panel area and light switch zone.
• If you do not see it immediately, scan the side walls from top to mid-height.
• Write down both the model number and serial number exactly as shown.

The model and serial label is the reference point we use to match the correct Kenmore refrigerator parts, diagrams, and troubleshooting information.

Kenmore side-by-side refrigerators can look similar across multiple model series, but parts like an ice maker assembly, door gasket, or thermostat can vary by model. Using the label prevents ordering the wrong replacement part.

• Confirm your model number first in the owner's manual.
• If you are ordering parts, start with the parts list for model 1069552811, then use Sears PartsDirect to search by model number if you need additional items.
• For ice and water dispenser issues, use the model series troubleshooting info in Kenmore 106 model refrigerator error codes.

Last updated: February 2026

On Kenmore model 1069552811, a bad compressor shows up as poor or no cooling even though the unit keeps trying to run; you often hear repeated clicking (start attempt then shutoff) or it runs for long periods but temperatures never recover. Use the sound guide in the 1069552811 owner's manual to separate normal noises from failure symptoms.

• Refrigerator and freezer stay warm or slowly get warmer
• Compressor runs almost constantly with little cooling
• Repeated clicking every few minutes (start device trips)
• Compressor shell becomes very hot (use caution)
• You hear running but cooling performance stays weak

Many “bad compressor” symptoms are caused by airflow, defrost, or door seal problems.

• Listen for normal sounds: gurgling after shutdown, occasional timer or thermostat clicks
• Confirm airflow in the freezer; a failed fan can mimic compressor trouble
• Check for heavy frost on the freezer back wall (defrost problem)
• Inspect door gaskets and door alignment; poor sealing causes moisture, frost, and warm temps

The compressor is part of the sealed refrigeration system; misdiagnosis can lead to unnecessary, expensive repairs when the real issue is a defrost failure, airflow restriction, or a leaking door gasket.

If testing confirms the compressor is the issue, the model-matched replacement is the refrigerator compressor W10309990. You can also order other parts for model 1069552811 from the parts list, or search by model on Sears PartsDirect.

Last updated: February 2026