KitchenAid KUIX535HBS00 freestanding icemaker Parts

For the KitchenAid KUIX535HBS00 freestanding ice maker, the most reliable reset is a power reset: turn the unit OFF, then disconnect power briefly and restore power; when you turn it back ON, it will run a short rinse cycle (about 5 minutes) and resume normal operation. For model-specific control behavior, use the owner's manual.

Quick reset steps (power reset)

• Press the ON/OFF button to turn the ice maker OFF.
• Wait 5 to 10 minutes so any ice can drop into the bin.
• Disconnect power (unplug or switch the breaker OFF), then restore power.
• Turn the ice maker ON.
• Wait for the rinsing cycle (about 5 minutes) to confirm it is operating.

What to check if it still will not run

• Confirm it is plugged into a grounded 3-prong outlet.
• Make sure the control is turned on.
• Check the breaker or fuse.
• Verify room temperature is above 45°F (7°C); colder rooms can prevent restart.
• If water is sitting in the bin on drain-pump setups, check the drain hose for kinks or pinches.

Reset vs. clean cycle (what is different)

If the issue is slow ice production or scale buildup, a reset may not help; the cleaning cycle is the correct “system reset” for water flow and mineral scale.

Action	What it does	When to use it
Power reset	Reboots the control and restarts the rinse/startup sequence	After a glitch, no ice, odd behavior
CLEAN cycle	Flushes the water system to remove mineral scale	“Cleaning Needed” light, reduced ice output

Why it matters

A proper reset gets the control and rinse/startup sequence back in sync. If the unit is not draining correctly or the room is too cold, it can look like a control problem even when it is an installation or environment issue.

Parts that commonly relate to “won’t make ice” symptoms

If troubleshooting points to a failed component, these are common suspects for this model:

• Pump, recirculating (includes sensor) W11542867 (circulates water over the evaporator)
• Valve W10897719 (water fill issues)
• Control-elek W11034363 (control problems)

For ordering, we list model-matched parts for KUIX535HBS00 on this page, and you can also search by model on Sears PartsDirect.

Last updated: February 2026

Your KitchenAid KUIX535HBS00 is a freestanding ice maker, not a stand mixer; it does not have a “quart bowl” capacity. For capacity details that apply to this ice maker (ice storage and water system information), use the specifications and feature notes in the KUIX535HBS00 owner's manual.

What “quarts” usually means (and why it does not apply here)

When customers ask “how many quarts,” they are usually referring to a stand mixer bowl size (for example, 4.5 qt or 5 qt). A freestanding ice maker like the KUIX535HBS00 is measured differently:

• Ice storage bin capacity (often listed in pounds, not quarts)
• Daily ice production rate (pounds per 24 hours)
• Water supply requirements (pressure range, plumbing connection)
• Cabinet cutout and ventilation clearances
• Electrical requirements

Where to find the correct capacity specs for KUIX535HBS00

We recommend checking these sections in the KUIX535HBS00 owner's manual because they are the most reliable for your exact model:

• Product specifications and features
• Installation location and leveling guidance
• Water supply requirements (including pressure guidance)
• Cleaning cycle and maintenance notes

Quick reference: common capacity terms

If you meant...	Typical unit	Applies to KUIX535HBS00?
Mixer bowl size	Quarts	No
Ice bin storage	Pounds	Yes
Ice production	Pounds per day	Yes
Water supply pressure	PSI	Yes

Why it matters

Using the right capacity measurement helps you buy the right appliance and set it up correctly. For example, this model’s manual notes that excessive water pressure can cause loud filling noises; proper installation and water pressure help the inlet valve and water system run normally.

Ordering parts for your ice maker

If you are troubleshooting performance (no ice, thin ice, loud fill, slow production), common related parts for this model include the valve W10897719 and the pump, recirculating (includes sensor) W11542867. You can order replacement parts from the parts list for KUIX535HBS00, or search by model on Sears PartsDirect.

Last updated: February 2026

A freestanding ice maker like KitchenAid model KUIX535HBS00 typically lasts 10 years with normal home use. Regular cleaning to control mineral scale, good ventilation, and protecting the water line from freezing are the biggest factors that keep the sealed system, pumps, and controls running longer.

Typical life expectancy by ice maker type

Most customers see these ranges:

• Freestanding undercounter ice makers (like KUIX535HBS00): about 10 years
• Refrigerator ice makers (built-in modules): about 7 years
• Light commercial-style units in a home: about 10 years

Ice maker type	Typical life expectancy	What usually ends life first
Freestanding undercounter	10 years	Pump, control, sealed system wear
Refrigerator ice maker	7 years	Mold module, valve, gear wear
Heavy-use home setup	10 years	Scale buildup, ventilation issues

What extends life the most (and what shortens it)

These are the biggest real-world drivers of lifespan:

• Clean the water system on schedule to prevent mineral scale buildup
• Keep the front grille area unobstructed so the unit can ventilate properly
• Turn off water and power during long periods of non-use
• Protect the water supply line from freezing conditions
• Use gentle cleaners on stainless surfaces (avoid abrasive cleaners and chlorine bleach)

Maintenance that matters most for KUIX535HBS00

Minerals naturally get rejected during freezing and can form scale in the water system; that scale is a top cause of early pump and water-system problems. We follow the cleaning intervals and steps in the KUIX535HBS00 owner's manual.

If you are troubleshooting weak ice production or odd cycling, these model-specific parts are commonly involved:

• Pump, recirculating (includes sensor) W11542867 (circulates water over the freezing plate)
• Valve W10897719 (controls water fill)
• Ice maker drain pump W11542868 (drains mineral-heavy water after cycles)

Why it matters

A freestanding ice maker is designed to cycle at preset temperatures and drain mineral-heavy water after each freeze cycle. When scale builds up or airflow is restricted, the machine works harder, makes less ice, and key components wear out sooner.

Last updated: February 2026

If your KitchenAid freestanding ice maker model KUIX535HBS00 runs but makes no ice, the cause is usually a control setting, water supply issue, or a drain problem (like a loose drain cap or blocked drain tube). We recommend checking these items first, then testing key components.

Quick checks that fix most “no ice” problems

• Confirm the control is turned On (see owner's manual).
• Verify the water supply line is connected and the shutoff valve is fully open.
• Make sure incoming water pressure is in a normal range (typically 30 to 120 psi).
• Check the drain cap; if it is loose, the water pan can empty and you can get thin ice or no ice.
• Clean the drain tube and confirm the drain line is not kinked.
• Ensure the front grille area is unobstructed so the unit can ventilate properly.

What to check next (common part-related causes)

If the basics look good, these parts commonly affect ice production on this model:

Symptom	What it often points to	Part to consider
No water entering the unit	Water inlet valve not opening	Valve W10897719
Water present but not circulating over the evaporator	Recirculating pump not moving water	Pump, recirculating (includes sensor) W11542867
Unit drains unexpectedly or will not drain correctly	Drain pump or drain path issue	Ice maker drain pump W11542868
Ice forms but is not cut into cubes/slabs correctly	Cutter grid issue	Grid-assy, 2 W10919199

Safe troubleshooting steps we use

1. Unplug the ice maker before inspecting wiring or components.
2. Inspect the water line and drain line routing for kinks or pinches.
3. Clean the condenser area if airflow is restricted by lint or dust.
4. If you have a multimeter, check for power to the valve and pumps during a fill or circulation step.
5. Replace the failed component using the parts list for KUIX535HBS00, or search by model on Sears PartsDirect.

Why it matters

This ice maker relies on a steady fill, proper recirculation, and correct draining. If the drain cap is loose or the drain tube is restricted, the water pan can empty before a full freeze cycle completes, which directly results in little or no ice.

Last updated: February 2026