Kenmore 11016852500 washer Parts

For Kenmore washer model 11016852500, we identify the correct model by finding the model and serial number label on the washer. On this style of Kenmore top-load washer, the label is located under the washer lid, and the model number typically starts with 110. (followed by more digits). See the 11016852500 owner's manual for the exact label location and what to record.

Where to look on the washer

Check these common Kenmore washer label locations:

• Under the lid on the rim of the opening (most common for top-loaders like model 11016852500)
• On the rear panel of the cabinet
• Near the control panel area (depending on design)
• Inside the lid itself (less common)

What the model number looks like (and why it matters)

Kenmore washer model numbers often begin with 110 and are usually 11 characters or more. Using the full model number helps us match the correct diagrams and parts, especially for items like the lid switch, drain pump, and drive system.

Quick checklist

• Write the model number exactly as shown (include all digits)
• Record the serial number too (helpful for production variations)
• Use the model number when ordering parts or checking fit

Common parts that depend on the exact model

Even small model differences can change which parts fit. For model 11016852500, examples of model-specific parts include:

Part type	Example part on this model page	What it affects
Lid safety switch	Washer lid switch assembly WP8318084	Spin/agitate operation and safety
Drain system	Washer drain pump WP3363394	Draining and spin performance
Agitation drive	Agitator dog 80040	Agitator movement and wash action

Why it matters

Using the exact Kenmore model number prevents ordering the wrong replacement part, reduces return hassles, and speeds up troubleshooting because the wiring, controls, and mechanical drive parts can vary by revision.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11016852500, correct installation (level floor, proper water pressure, and a grounded outlet) and routine care help you reach the high end of that range; see the 11016852500 owner's manual for care guidance.

Typical lifespan and what affects it

Most washers land in the same general window, but these factors move the needle:

• Load size and frequency: frequent heavy loads shorten drivetrain life.
• Overloading: increases stress on the clutch, drive system, and suspension.
• Water quality and temperature: very hot water and mineral buildup can accelerate wear.
• Installation conditions: an unlevel floor increases vibration and component fatigue.
• Maintenance habits: periodic cleaning and checking hoses reduces preventable failures.

Model-specific installation basics that support longevity

Your installation guide calls out key requirements that protect the washer over time:

Item	Recommended for 11016852500	Why it matters
Hot water temp	120°F (49°C)	Helps cleaning without overheating components
Water pressure	5 to 100 psi	Prevents fill problems and valve strain
Floor	Level; max 1 in. slope under washer	Reduces shaking and wear
Electrical	Grounded outlet within 4 ft	Prevents power and safety issues

For the full setup details, use the 11016852500 installation guide.

Parts that commonly wear first (and why)

When a washer stops agitating, won’t spin, or makes new noises, these are frequent wear items:

• Agitator dog 80040: worn dogs can cause weak or no agitation.
• Washer motor coupling 285753A: a common driveline failure that can stop spin/agitate.
• Clutch 285785: wear can lead to slow or no spin under load.
• Washer drain pump WP3363394: failures often show up as no-drain or leaking.

Why it matters

Knowing the 10 to 15 year average helps you decide whether to repair or replace. If your 11016852500 is within that window, replacing a targeted part (like a coupling or pump) often restores reliable performance without replacing the whole washer.

Last updated: February 2026

For Kenmore washer model 11016852500, the most commonly replaced parts are the ones that affect draining, spinning, and agitation. If your washer will not drain, will not spin, or agitates poorly, these are the first parts we check and replace. See the owner's manual for operating and care tips that help prevent repeat failures.

Most common replacement parts (and what they fix)

• Lid switch: washer will not spin or drain if the lid is not sensed as closed; consider the washer lid switch assembly WP8318084.
• Drain pump: slow drain, no drain, or humming with no water movement; consider the washer drain pump WP3363394.
• Motor coupling: motor runs but tub will not agitate or spin; consider the washer motor coupling 285753A.
• Agitator dogs: agitator “slips” or only moves one direction; consider the agitator dog 80040.
• Clutch: weak spin, burning smell, or clothes still wet at end of cycle; consider the clutch 285785.
• Suspension spring: excessive vibration or “walking”; consider the washer suspension spring WP63907.

Quick symptom-to-part guide

Symptom	Most likely parts to check first	What you may notice
Will not spin	Lid switch, clutch	Stops before spin, wet clothes
Will not drain	Drain pump, drain hose issues	Standing water, pump hum
No agitation	Motor coupling, agitator dogs	Tub fills but clothes do not move
Loud banging/shaking	Suspension spring	Off-balance loads, cabinet movement

Why these parts fail most often

These parts handle the most stress: frequent lid openings, heavy loads, and water flow. Wear items like couplings, clutches, and agitator components are designed to take the abuse so the drive system is protected.

Tips to reduce repeat repairs

• Avoid overloading; heavy loads strain the clutch and coupling.
• Use the correct water level and cycle for bulky items.
• Check pockets and small items; debris can damage the drain pump.
• Replace inlet hoses every 5 years and inspect for bulges or leaks (noted in the manual).

Last updated: March 2026