Kenmore 11047511701 washer Parts

To hard reset your Kenmore washer model 11047511701, unplug it (or switch off the breaker) for 1 minute, restore power, then press STOP/CANCEL to clear the control and restart a cycle. This resets the control logic and clears many “stuck” conditions.

Quick reset steps (most effective)

• Press STOP/CANCEL once to pause, or twice to cancel and power down.
• Unplug the washer (or turn the breaker off) for 60 seconds.
• Plug it back in (or turn the breaker on).
• Select a cycle and press and hold START for about 1 second to begin.
• If the door will not unlock, wait for the washer to drain automatically if water level or temperature is high.

For the exact button names and cycle-cancel behavior on this model, use the 11047511701 owner's manual.

What “STOP” does on this model

The manual for Kenmore 11047511701 describes these control behaviors:

What you want to do	What to press	What to expect
Pause the cycle	STOP once	Cycle pauses; you can resume with START
Cancel the cycle	STOP twice	Washer powers down; door unlocks after safe drain
Restart with a new cycle	STOP once, pick cycle/options, then START (hold 1 sec)	New cycle starts from the beginning

If you were trying to enter diagnostics

A “hard reset” is different from diagnostic mode. If you are seeing flashing lights or an error code, use the correct troubleshooting path first.

• Write down the exact code (for example, DC, ND, NF, LE, UE).
• Cancel the code with STOP.
• Check for common causes: unbalanced load, drain restriction, or water supply issue.
• If the issue returns immediately after a reset, troubleshoot the specific code.

A good starting point for code-related issues is Kenmore 110 high efficiency front load washer error codes.

Why it matters

Resetting power clears temporary control glitches, but repeated errors usually point to a real problem such as a drain blockage, door lock issue, or load balance problem. Using the correct cancel and restart steps prevents unnecessary part replacement.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use and routine care. For your Kenmore 11047511701, keeping up with cleaning and periodic maintenance (as outlined in the 11047511701 owner's manual) is the most reliable way to reach that lifespan.

What affects washer lifespan most

• Load size and balance: frequent overloading or unbalanced loads increase wear on the drive system and tub support.
• Detergent use: too much detergent can cause residue buildup and odors, which leads to more cleaning and component stress.
• Water quality: hard water can leave mineral deposits in the tub and hoses.
• Drain and filter care: restricted draining makes the washer work harder and can trigger performance problems.
• Door seal condition: a leaking or moldy boot can lead to water damage and recurring service issues.

Maintenance that helps you get the full 10 to 15 years

Use these habits to reduce breakdowns and extend the life of the motor, belt, and controls:

• Run a regular washer-cleaning routine (follow the schedule in the manual).
• Leave the door slightly open between loads to dry the drum and door seal.
• Check and tighten inlet hoses periodically; replace aging hoses before they burst.
• Clean the drain system as needed; if your model uses a serviceable filter, keep it clear.
• Level the washer to reduce vibration and stress on the suspension.

Common “end-of-life” signs vs. repairable issues

Symptom	Often repairable?	Common area involved
Loud rumbling in spin	Sometimes	Tub support, bearings, basket support
Won’t spin or slips	Often	Belt, motor, control
Water leaking at door	Often	Door boot, clamps
Repeated drain problems	Often	Drain path, pump/filter restrictions

If you’re seeing door leaks or mildew that won’t clean up, the washer door boot WPW10111435 is a common wear item on front-load designs.

Why it matters

Knowing the typical 10 to 15 year lifespan helps you decide whether to invest in a repair (like a belt, door seal, or control) or plan for replacement when major components wear out.

Last updated: February 2026

You can identify your Kenmore washer model by finding the model/serial label on the machine; on Kenmore model 11047511701, it’s typically on the cabinet (often near the bottom), behind the door or in the door jamb on front-load designs, or on the back or top edge of the control panel. Use the exact model number when ordering parts.

Where to look first (fastest checks)

• Open the washer door and check the door jamb and the area just behind the door opening
• Look along the inside edge of the front panel near the bottom
• Check the back of the control panel
• Check the top edge of the control panel (rear lip)
• Look on the side of the main cabinet near the bottom

What the label looks like and what to copy

The label usually includes a model number and serial number. For parts lookup, the model number is the key.

What you see on the label	What it’s used for	Example
Model number	Matches the correct parts diagrams and parts list	11047511701
Serial number	Identifies production run details	Varies
Electrical ratings	Helps confirm correct power requirements	Varies

Tips to avoid ordering the wrong part

• Copy the model number exactly, including all digits
• If the label is worn, take a clear photo and zoom in to confirm characters
• Match the model number to the documentation; our 11047511701 owner's manual is a reliable cross-check

Why it matters

Kenmore washers can look similar across multiple model families, but parts like a door boot, control board, or drive belt can differ by model. Using the exact model number helps ensure the right fit and avoids repeat repairs.

Last updated: February 2026

A washing machine like Kenmore model 11047511701 is built around a wash drum, drive system, water fill and drain components, and controls that manage the cycle. Inside, you will typically find suspension parts to control vibration, a dispenser system, and serviceable items such as a drain pump filter.

Main internal parts you will typically find

• Wash drum and outer tub: the stainless steel drum holds clothes; the outer tub holds water around the drum
• Drive system: motor and belt (or direct drive on some designs) that turns the drum
• Drain system: drain pump, hoses, and a clean-out filter that catches debris
• Water fill system: inlet valves and inlet hoses that bring hot and cold water in
• Dispenser system: compartments that release detergent, bleach, and softener at the right time
• Suspension system: springs and shock absorbers that reduce “walk” and off-balance vibration
• Controls and wiring: electronic control board, user interface, and wire harnesses

Parts you can actually service on this model

These are common “inside the washer” parts we see customers replace on Kenmore 11047511701:

• Filter WPW10730972 (drain pump clean-out filter)
• Washer drive belt WP8540101 (connects motor to the drive pulley)
• Washer drive motor WPW10140581 (powers drum movement)
• Washer electronic control board WPW10163007 (controls cycle functions)
• Wire harness WPW10204534 (electrical connections between components)

Quick map: what each part does

Part area	What it does	Common symptom when it fails
Drain pump and filter	Drains water; traps lint/coins	Slow drain, gurgling, “SD” suds routine after poor draining
Suspension (springs, shocks)	Reduces vibration and off-balance	Walking, banging, excessive vibration
Dispenser system	Releases detergent/bleach/softener	Poor cleaning, residue in dispenser
Controls (UI + board)	Runs timing, sensing, and motor control	No start, stuck cycle, erratic operation

Why it matters

Knowing the internal parts helps you troubleshoot faster. For example, gurgling during draining can be normal, but repeated slow draining often points to a clogged filter or drain path. The suspension system also plays a big role in vibration and off-balance loads.

Where to confirm what’s in your washer

For the exact component layout and service access points for Kenmore 11047511701, use the 11047511701 owner’s manual.

Last updated: February 2026

Yes, it’s usually worth repairing a Kenmore washer when the fix restores reliable operation for less than the cost of replacement, especially for a solid front-load model like Kenmore 11047511701. We also recommend paying for a diagnosis first so you’re deciding based on the exact failed part.

A practical way to decide (repair vs. replace)

Use these checkpoints to make a clear call:

• Repair cost vs. replacement cost: If the total repair is under about 50% of a comparable new washer, repair is typically the better value.
• What failed: Wear items (like a belt or filter) are usually cost-effective; major structural or tub issues can be pricier.
• How the washer has been maintained: Regular cleaning and proper loading often mean a repair will last longer.
• Downtime and hassle: If you need a fast, predictable fix, replacing a common part is often quicker than shopping for a new unit.
• Symptoms and error codes: Error codes can point to a specific system (drain, motor, balance) and help estimate repair scope.

Common repairs that are often “worth it” on this model

For Kenmore 11047511701, these are examples of repairs that frequently make sense because they’re targeted and parts are available:

Issue you notice	Likely area	Example part for this model
Won’t spin or slips under load	Drive system	Washer drive belt WP8540101
Leaks at the door	Door seal/clamps	Washer door boot WPW10111435 and/or washer door boot spring clamp WP8540108
Odor, slow drain, debris buildup	Drain filtration	Filter WPW10730972

When replacement is the better move

Replacement is usually the smarter choice when:

• The outer tub or basket area is damaged and the estimate is high.
• Multiple major systems are failing (for example, control + motor + leak).
• The washer has repeated breakdowns close together.

Why it matters

A washer repair decision is really a cost-per-year decision. The manual notes that some items are normal wear parts (for example, filters and belts), so replacing those can be a normal, economical way to keep the washer running well. For model-specific care and troubleshooting steps, use the 11047511701 owner’s manual.

Last updated: February 2026

Yes. Kenmore washer model 11047511701 uses filtering to help keep debris out of the drain system; it also has inlet valve screens at the water connections that can clog with sediment. For the exact filter locations and cleaning intervals, use the 11047511701 owner's manual.

What “filter” means on this Kenmore washer

Top-load washers typically do not have a large, front access coin-trap door like many front-load designs. On model 11047511701, filtering is usually handled in these common places:

• Water inlet valve screens inside the hot and cold inlet ports
• Drain system filtering that helps keep lint and small debris from reaching the pump
• Tub and basket areas where items like coins can collect and later cause drain issues

How to check and clean the most common filter: inlet screens

Sediment-clogged inlet screens cause slow fill, long cycle times, and fill-related errors.

• Unplug the washer and turn off both water supply valves
• Remove the hot and cold fill hoses from the back of the washer
• Inspect the small metal screens inside the inlet ports
• Rinse screens with running water; use a soft brush if needed
• Reinstall hoses, turn water back on, and check for leaks

Symptom	Most likely “filter” area	Best first step
Slow fill or no fill	Inlet valve screens	Clean inlet screens; verify valves fully open
Won’t drain or drains slowly	Drain path restriction	Check drain hose for kinks; reduce oversudsing
Wet clothes after spin	Drain restriction or load balance	Confirm draining first; then rebalance load

When a part replacement makes sense

If you find a damaged or missing filter component during inspection, replacement is the fastest fix. The model-listed part is the filter WPW10730972.

Why it matters

Keeping inlet screens and the drain path clear prevents slow fills, poor draining, and extra strain on the pump and control system; it also helps your Kenmore washer maintain normal cycle times.

Last updated: February 2026

Kenmore washer model 11047511701 (HE2Plus front-loading) has a 3.5 cu. ft. capacity. For the official spec wording and any model-variant notes, confirm the capacity listing in the 11047511701 owner's manual.

Capacity details for model 11047511701

This is a full-size Kenmore front-load washer designed for HE (high-efficiency) detergent and tumbling wash action.

• Capacity: 3.5 cu. ft.
• Washer type: Front-load
• Detergent requirement: HE detergent
• Best loading practice: leave space for items to tumble freely

How we recommend using that capacity (real-world loading)

Even with a 3.5 cu. ft. drum, performance depends on how the load is packed.

• Fill the drum loosely; do not compress laundry
• Keep bulky items (comforters, jackets) balanced with a few smaller items
• Avoid mixing one heavy item by itself (it can cause out-of-balance spinning)
• Use the correct cycle for bulky or bedding loads

Load type	What to watch for	What “right” looks like
Everyday mixed load	Tumble space	Items lift and drop, not packed tight
Bulky/bedding	Balance	Evenly distributed, no single heavy clump
Towels/denim	Water and spin	Not overfilled; spins without banging

Why it matters

Knowing the exact 3.5 cu. ft. capacity helps you size loads correctly, improve cleaning, and reduce vibration. Overloading increases strain on wear parts like the door seal and drive belt.

If you are checking capacity because the washer is shaking or showing a balance-related code, use our Kenmore front load washer ue error code troubleshooting steps to narrow down the cause.

Last updated: February 2026