Installation guide
Owner’s manual
Error Codes
How long should a Kenmore gas stove last?
A Kenmore gas range like model 79078923000 typically lasts 15 years with normal household use. Keeping burners clean, ensuring proper ignition, and addressing weak oven heating early (often igniter-related) helps you get the full service life; see the 79078923000 installation guide for safe operating checks.
Most ranges reach their expected life when heat and ignition components stay in good condition.
- Cooking frequency and high-heat use (daily cooking shortens life)
- Burner cap and burner head cleanliness (prevents poor flame and delayed ignition)
- Oven ignition health (slow ignition strains components)
- Proper gas supply and leak-free connections
- Keeping vents and airflow paths clear to reduce heat stress on controls
If your range is approaching the 10 to 15 year mark, these symptoms often signal it is time for repair planning.
| Symptom | Common cause | What we recommend |
|---|---|---|
| Surface burner clicks but lights slowly | Dirty burner ports or mis-seated cap | Clean and reseat caps; verify each burner lights within about 4 seconds |
| Oven takes 30 to 60 seconds before flame appears, then gets slower over time | Weak igniter or gas flow issue | Compare ignition timing; inspect igniter circuit and flame quality |
| Oven temperature swings or bakes unevenly | Sensor drift or control issue | Test the range oven temperature sensor 5304504897 and check calibration steps in the manual |
| Oven light out repeatedly | Bulb/socket wear | Replace the range oven light bulb 316538904 and inspect the socket for heat damage |
A gas range can keep running well past mid-life, but ignition delays and unstable temperatures waste gas, increase cooking time, and can overheat wiring and controls. The installation instructions also call out verifying proper burner ignition and flame after hookup, which is a good performance baseline to revisit over time.
- Keep burner caps installed and properly seated during use
- Prevent spills and cleaners from entering burner gas openings
- Clean burner heads and caps regularly; dry fully before reassembly
- If the oven flame is slow to appear, troubleshoot promptly (often igniter-related)
Last updated: February 2026
Where to find model number on Kenmore Elite gas range?
On the Kenmore Elite gas range model 79078923000, the model number is typically printed on a rating label around the oven door opening or on the frame behind the lower storage or warming drawer. Use the exact model number from that label when ordering Range parts or looking up specs in the 79078923000 owner's manual.
Check these spots in order (they are the most common on Kenmore ranges):
- Door jamb/frame: open the oven door and look along the front frame (left or right side).
- Behind the bottom drawer: pull the storage or warming drawer fully out and look on the frame rails.
- Back panel: look near the rear cover or vent area.
- Side frame: sometimes on a side panel edge, visible when the drawer is removed.
- Turn the oven light on and use a flashlight to scan the front frame.
- Remove the bottom drawer (most slide out; lift slightly at the end of the travel and pull).
- Write down the full model number and the serial number exactly as shown.
Most labels include the same key fields:
| Label field | What to copy | Why it matters |
|---|---|---|
| Model | 79078923000 | Ensures diagrams and parts match your exact range |
| Serial | Letters and numbers | Helps confirm production run and compatible revisions |
| Gas type | Natural gas or LP | Needed for correct orifices and conversions |
Kenmore Elite ranges often have multiple versions that look similar. Using the exact model number prevents ordering the wrong igniter, control board, burner parts, or an LP conversion kit.
Last updated: February 2026
Who makes Kenmore 79078923000?
Kenmore is a brand name, and the Kenmore Elite gas range model 79078923000 was manufactured for Kenmore by another appliance maker (Kenmore does not operate its own range factory). For this model, the most reliable way to confirm the actual manufacturer is to use the identification information and documentation for the unit.
Use these checks in order; they work even if the range has been moved or the kitchen has been remodeled:
- Check the serial plate location: it is on the decorative bottom trim and is visible when the lower oven door is opened.
- Compare the serial plate details to the information in the 79078923000 installation guide.
- Use the model and serial information when ordering parts such as an igniter, spark module, or oven control.
- If you are matching parts by design, look for telltale features like burner head style, igniter connector type, and control layout.
Different manufacturers use different wiring layouts, igniter styles, and gas valve configurations. Confirming the maker helps you avoid ordering the wrong component and speeds up diagnosis.
| What you are doing | What to use | Why it helps |
|---|---|---|
| Ordering replacement parts | Model and serial plate info | Ensures correct fit and electrical/gas compatibility |
| Diagnosing ignition problems | Wiring diagram and component IDs | Helps trace power to igniters and spark module |
| Planning service | Installation and safety notes | Reduces risk when checking gas connections |
If you are troubleshooting symptoms, these are common parts customers replace on gas ranges like the 79078923000:
- Range spark module 5304508269 for weak or no sparking at surface burners
- Frigidaire range bake igniter 316489406 for an oven that will not heat or takes too long to ignite
- Range oven temperature sensor 5304504897 for inaccurate oven temperatures
Kenmore model numbers often map to a specific manufacturing platform; confirming the platform using the serial plate and the documentation helps ensure the right Kenmore Elite range parts, wiring, and gas components are selected.
Last updated: February 2026
