Kenmore 25357388600 refrigerator Parts

Yes. We still support Kenmore refrigerator parts, and for Kenmore model 25357388600 you can commonly replace maintenance items (like water filters and door gaskets) and many functional parts (like ice maker and dispenser components). Use the model-specific diagrams and procedures in the 25357388600 owner's manual to match parts correctly.

What parts are typically still available for this model

For Kenmore 25357388600 side-by-side refrigerators, these are common, high-demand replacements we see customers order:

• Water filter: genuine Kenmore refrigerator water filter WFCB (replacement cartridge 46 9910)
• Ice system parts such as the ice maker mold
• Door sealing parts such as fresh food and freezer gaskets
• Cooling and defrost parts such as the defrost bi-metal thermostat and evaporator fan blade
• Convenience parts such as bins, crisper pans, and light bulbs

How to make sure you order the right part

Even when a part name sounds right, the safest match is always by model number and the exact part ID.

• Confirm the full model number is 25357388600 (from the rating label inside the refrigerator)
• Use the exploded-view diagrams to identify the part location and callout number
• Match the part by part ID (not just description)
• For water filters, follow the cartridge style and housing location shown in the manual
• If you are replacing a gasket, match the correct door (fresh food vs freezer)

What you are replacing	Best way to match it	Example from this model
Water filter	Filter system type and cartridge ID	WFCB (46 9910)
Door gasket	Door side and gasket part ID	Fresh food vs freezer gasket
Ice storage or dispenser parts	Bin style and dispenser configuration	Ice container, auger motor

Why it matters

Ordering by the exact model and part ID prevents fit issues, leaks (water filter housing and O-ring sealing), and dispenser or door-closing problems that can cause temperature swings and frost buildup.

Last updated: February 2026

Your Kenmore side-by-side refrigerator model 25357388600 has its exact cubic-foot capacity listed on the serial/rating plate inside the fresh food compartment; that plate is the most accurate source for your specific unit. We also recommend confirming the spec in the 25357388600 owner's manual.

Fast ways to find the cubic feet (capacity)

• Check the serial/rating plate inside the refrigerator compartment (usually on a side wall). Write down the listed capacity.
• Use the model number (25357388600) to match specs in the 25357388600 owner's manual.
• If the label is hard to read, clean it with soap and water only so the print stays intact.
• If you are measuring for fit, also confirm overall dimensions in the 25357388600 installation guide.

Where to look and what to record

The rating plate is inside the refrigerator compartment. Record these items so you can match the correct specs and parts:

• Model number: 25357388600
• Serial number
• Purchase date (helpful for service history)

What you need	Where to find it	Why it matters
Cubic feet (capacity)	Serial/rating plate	Confirms true storage volume for your exact unit
Model and serial	Serial/rating plate	Ensures correct parts and documentation
Cutout/clearance needs	Installation guide	Prevents door swing and ventilation problems

Why it matters

Cubic feet is used to compare storage space across refrigerators, but it is also a practical check for kitchen planning and organization. Using the rating plate avoids mix-ups when similar Kenmore 253-series models have different capacities.

Last updated: February 2026

Most Kenmore side-by-side refrigerators weigh about 250 to 320 lb empty; for Kenmore model 25357388600, use the exact shipping or net weight listed in the 25357388600 owner's manual or the 25357388600 installation guide when you need a precise number for moving or delivery.

Typical weight ranges (what to expect)

Side-by-side refrigerator weight varies mainly by cabinet size, dispenser/ice maker hardware, and insulation.

• Counter-depth units often run 220 to 280 lb
• Standard-depth units often run 260 to 340 lb
• Built-in ice and water features can add 10 to 25 lb
• Packaging and pallet can add 30 to 80 lb to shipping weight

Why the exact weight matters

Knowing the correct weight helps prevent floor damage and injuries, and it ensures you plan the right equipment and help for the job.

Quick planning guide

Task	Use this weight	Why
Carrying up/down stairs	Net (unboxed)	What you actually lift
Delivery appointment	Shipping (boxed)	What the carrier handles
Protecting floors	Net + load distribution	Prevents dents and cracked tile

Tips for moving a side-by-side safely

• Empty food, remove bins and shelves, and tape doors shut
• Disconnect power; then disconnect the water supply line (if equipped)
• Use an appliance dolly with straps; keep the unit as upright as possible
• Measure doorways and turns; side-by-sides are wide and hard to pivot
• If the refrigerator was laid down, let it stand upright before plugging in (follow the timing in the manual)

Related model-specific parts that affect handling

If your refrigerator has an internal filter and dispenser setup, those components add weight and can be damaged if the unit tips.

• Genuine Kenmore refrigerator water filter WFCB (cartridge 46 9910 referenced in the manual)

Last updated: February 2026

For Kenmore model 25357388600, the model number is the full identifier we use to match the correct refrigerator parts and documentation; the first three digits (253) are the source/manufacturer prefix, and the remaining digits identify the exact design and version.

Where to find the model number on this refrigerator

On most Kenmore side-by-side refrigerators, the model and serial tag is typically located in one of these spots:

• Inside the fresh food compartment on a side wall
• On the ceiling area inside the fresh food compartment
• Along the door frame (hinge side)
• Behind the toe grille (lower front)
• On the back of the cabinet (less common for daily access)

For diagrams and the exact tag location callouts for this unit, use the 25357388600 owner's manual.

How to decode a Kenmore model number (quick guide)

Kenmore model numbers are usually structured as a prefix + model identifier + suffix/version.

Section	Example (25357388600)	What it tells you	Why it matters
Prefix	253	Manufacturer/source code	Helps identify the platform and parts family
Core model	573886	Main design series	Drives most part compatibility
Suffix/version	00	Revision/package	Can affect small part changes

Why the full model number matters when ordering parts

Using the complete model number prevents mismatches, especially for parts that vary by revision. Common examples include:

• Refrigerator water filter style and housing
• Ice maker and dispenser components
• Door bins, crisper pans, and shelf supports
• Gaskets and trim pieces
• Electrical items such as light bulbs and thermostats

If you are replacing the water filter on this model, the manual calls out the Kenmore replacement cartridge 46 9910, which matches the genuine Kenmore refrigerator water filter WFCB.

Why it matters

A single missing digit can point to a different parts list, which can lead to ordering a door gasket, ice maker part, or filter that does not fit. Matching 25357388600 exactly keeps your repair accurate the first time.

Last updated: February 2026

To replace the ice maker in your Kenmore 25357388600 side-by-side refrigerator, we shut off power, stop ice production, remove the ice bin, disconnect the ice maker wiring and water fill tube, then install the new ice maker and restore water and power. Use the steps in the 25357388600 installation guide for safe water-line handling.

Before you start (safety and prep)

• Unplug the refrigerator (or switch off the breaker).
• Lift the ice maker wire signal arm to the OFF (up) position.
• Remove the ice container by lifting up and out.
• Protect the floor with towels; a small amount of water is normal.
• Confirm your household water pressure is 30 to 100 psi.
• Use the right tools: adjustable wrench, flat-blade screwdriver, Phillips screwdriver.

Replacement steps (typical side-by-side procedure)

1. Remove the ice bin and clear any ice chips from the chute area.
2. Remove the ice maker mounting screws and gently pull the ice maker forward.
3. Disconnect the wiring harness plug.
4. Disconnect the fill tube (if your design uses a tube at the rear of the ice maker).
5. Install the replacement ice maker: reconnect fill tube and wiring, then secure mounting screws.
6. Lower the wire signal arm to ON (down) and restore power.
7. Run a few harvest cycles; discard the first batch of ice.

Water line connection tips (to prevent leaks)

If you need to reconnect the supply line at the inlet valve, we follow these best practices from the installation instructions:

• Flush the supply line into a bucket until water runs clear.
• Use 1/4-inch (6.4 mm) OD copper tubing when applicable.
• Slide the brass compression nut and ferrule (sleeve) onto the tubing.
• Insert the tubing fully into the valve inlet (about 1/4 inch) and tighten carefully.
• Do not use a self-piercing shutoff valve.

Task	Power	Water supply
Remove ice maker	Off	On is OK (unless disconnecting supply line)
Disconnect supply line at inlet valve	Off	Off
Test for leaks and ice production	On	On

Why it matters

A correct install prevents slow leaks at the inlet valve, protects the dispenser area from ice jams, and helps the new ice maker fill properly so you get full-size cubes.

Related part (if you are servicing the ice bucket area): If your ice bin is cracked or won’t seat after realigning the auger, replace the ice container 241860803.

Last updated: February 2026

The SY EF code on a Kenmore refrigerator indicates a problem the control detects in the evaporator fan circuit (the fan that moves cold air through the freezer and into the fresh food section). On model 25357388600, start with the reset and airflow checks in the 25357388600 owner's manual.

What to do first (safe checks)

• Unplug the refrigerator for 5 minutes, then plug it back in.
• Confirm both doors close fully and nothing is holding them open.
• Make sure interior air vents are not blocked by food packages.
• Set both temperature controls to the center position; wait 24 hours for temperatures to stabilize.
• Listen for the evaporator fan when the compressor is running (you should hear airflow in the freezer).

Common causes and what usually fixes them

Symptom you notice	Most likely cause	Typical fix
Warm freezer and weak/no airflow	Evaporator fan not running	Clear ice obstruction; repair wiring; replace failed fan parts
Code returns quickly after reset	Loose connection in fan circuit	Reseat connectors; inspect harness for damage
Rattling or scraping noise	Fan blade hitting ice or shroud	Remove ice buildup; replace damaged blade

If the fan blade is cracked, warped, or rubbing, replacing the refrigerator evaporator fan blade 5308000010 restores proper airflow.

Why it matters

The evaporator fan is what distributes cold air. When the control senses the fan is not operating correctly, temperatures can rise, frost can build up, and food can spoil.

When service is the right next step

• SY EF returns immediately after a reset
• Heavy frost covers the freezer back wall
• Temperatures stay unsafe after 24 hours at the center settings

Use the 25357388600 owner's manual for model-specific access steps and control settings.

Last updated: February 2026

For Kenmore side-by-side refrigerator model 25357388600, the exact exterior dimensions are listed in the 25357388600 owner's manual. Most units in this series are built to fit a standard 33-inch-wide opening, so confirming width, height, and depth before delivery or cabinet changes prevents clearance and door-swing problems.

How to confirm the correct dimensions

We recommend checking the specification section in the manual and then measuring your installation space.

• Check the width, height, and depth listed for model 25357388600
• Measure your cabinet opening in three spots (top, middle, bottom)
• Allow clearance for door swing and drawer pull-out
• Account for rear space for the water line and power cord
• Include hinges and handles in the depth measurement if the manual specifies them

Quick measuring checklist (what to measure at home)

Use a tape measure and write down these numbers before ordering parts or planning a move.

What to measure	What to include	Why it matters
Opening width	Wall-to-wall at the front	Prevents binding during install
Opening height	Floor to cabinet/soffit	Avoids top clearance issues
Opening depth	Back wall to front edge	Ensures doors can close
Door swing space	In front of the unit	Prevents hitting walls/islands

Why it matters

A side-by-side refrigerator needs enough room for airflow and full door opening. If the opening is tight, even a small difference in depth (especially with handles) can cause rubbing doors, poor leveling, or difficult filter and bin access.

Related parts that can affect fit and access

If you are planning a tight install, these parts are commonly handled during moves or re-leveling:

• Door sealing and alignment issues often show up as gasket gaps (see refrigerator gasket 241786013 and refrigerator freezer gasket 241786014)
• Interior access changes if bins or drawers are removed and reinstalled
• Water line routing can affect how close the cabinet sits to the wall

Last updated: February 2026

Most Kenmore refrigerators average 10 to 15 years of service life; for a Kenmore side-by-side like model 25357388600, regular maintenance and quick fixes (seals, airflow, clean coils) are what most often determine whether it reaches the high end of that range. See the maintenance and care guidance in the 25357388600 owner's manual.

Typical lifespan and what affects it

A refrigerator’s life is usually driven by compressor run time, heat removal, and how well the doors seal.

• 10 to 15 years is the normal expectation for a household refrigerator
• Heavy use (frequent door openings, warm garage installs) shortens life
• Poor airflow (blocked vents, dirty condenser area) increases wear
• Weak door gaskets cause longer run times and temperature swings
• Water and ice features add components that need periodic service (filter, dispenser, ice maker)

Maintenance that most often extends life

These are the highest-impact habits we recommend for Kenmore side-by-side refrigerators:

• Keep door seals clean and closing tightly; replace if torn or warped
• Maintain stable temperatures (avoid frequent control changes)
• Keep interior vents clear so the evaporator fan can circulate air
• Replace the water filter on schedule to protect the water system
• Address frost buildup or warm temperatures early (before the unit runs nonstop)

Common “wear items” to plan for

Item	What it affects	Typical symptom when worn
Water filter	Water flow and ice quality	Slow dispense, odd taste/odor
Door gasket	Cooling efficiency	Moisture, frost, warm spots
Light bulb	Interior lighting	No light with door open

For this model, the correct filter is the refrigerator water filter WFCB (Kenmore replacement cartridge 46 9910 is referenced in the manual).

Why it matters

A refrigerator that runs longer to hold temperature uses more energy and puts extra load on sealed-system components (like the compressor). Simple upkeep, especially sealing and airflow, is the difference between “average life” and “early failure.”

Last updated: February 2026

On Kenmore refrigerator model 25357388600, the model and serial number are printed on the serial plate inside the fresh food (refrigerator) compartment. We recommend writing them down exactly as shown before ordering parts or scheduling service; see the 25357388600 owner's manual.

Where to look on the refrigerator

Check these common locations first (in this order):

• Inside the refrigerator compartment on a side wall (often upper area)
• Inside the refrigerator compartment near the crisper area (side wall behind or beside drawers)
• On the ceiling of the fresh food compartment (less common)
• Behind the toe grille or kick plate area (some designs)
• On the cabinet frame near the door hinge area (door open)

What to copy from the serial plate

Copy the information exactly, including any leading numbers.

• Model number (for this unit, it starts with 253)
• Serial number
• Purchase date (if you still have it)

Item	What it’s used for	Example format
Model number	Ensures parts fit your exact refrigerator	253XXXXXXXXXX
Serial number	Identifies production run and configuration	Letters and numbers

Why it matters

Kenmore refrigerators can look similar across multiple model families. Using the exact model number helps us match the correct parts (like a water filter, door gasket, or ice maker components) and avoid returns due to fit issues.

Quick tip before ordering parts

If the label is dirty, clean it gently with soap and water only (harsh cleaners can damage the printing), then re-check the numbers.

Last updated: February 2026