Kenmore Elite 11016942503 washer Parts

The Kenmore Elite washer model 11016942503 has a 3.2 cu. ft. wash basket capacity. Use this capacity to size loads correctly so the agitator can circulate items and the washer can drain and spin without going out of balance; see the owner's manual for cycle and loading guidance.

• Load loosely; don’t pack items down.
• Keep the load below the top of the basket so clothes can roll.
• Mix large and small items (for example, towels plus a few smaller pieces).
• Wash bulky items (comforters, blankets) one at a time when possible.
• If the washer bangs or “walks,” reduce the load size and rebalance.

Even with a 3.2 cu. ft. basket, usable capacity varies by fabric and cycle.

Correct loading helps your Kenmore 11016942503 clean better, spin out more water, and reduce strain on key drive and suspension parts. Chronic overloading commonly leads to vibration and wear in components like the washer suspension spring WP63907 and drive system.

Last updated: February 2026

Yes. Kenmore Elite model 11016942503 is part of Kenmore’s premium washer lineup, typically offering upgraded performance and features compared with standard Kenmore models. For the exact features and cycle options included on your specific washer, use the owner's manual.

Kenmore Elite generally indicates a higher-tier build and feature set within the Kenmore brand. On washers like the 11016942503, that usually shows up as better wash action, more cycle selections, and stronger component sets than entry-level models.

Common “Elite” expectations include:

• More cycle and option choices (for bulky, delicate, or heavy soil loads)
• Better load handling and cleaning performance when used with the right settings
• More robust mechanical drive components than basic models
• More detailed operating and care guidance in the manual

The fastest way to validate what your washer includes is to match the control panel features to the cycle descriptions and option charts.

Use this checklist:

• Compare your cycle knob and any option switches to the cycle descriptions
• Verify recommended load sizes and detergent guidance
• Check any special instructions for bleach and dispensers
• Record your model and serial number for future parts matching

Even a high-end washer can act “basic” if key wear parts are failing. If you’re troubleshooting performance (poor agitation, no spin, not draining), these are common items to inspect on this model:

“High end” is most noticeable when the washer is set up correctly (leveling, proper drain standpipe height, correct cycle selection) and maintained. The installation guide helps prevent vibration, out-of-balance issues, and draining problems that can make any washer feel underpowered.

Last updated: February 2026

Yes, repairing a Kenmore Elite washer like model 11016942503 is worth it when the problem is a common wear item (lid switch, drain pump, motor coupling, agitator parts) and the washer is otherwise in good shape. If the repair involves multiple major drive components, replacement becomes the better value.

Use these checks before you buy parts:

• Repair it when the symptom is isolated (won’t drain, won’t start, won’t agitate) and you can tie it to one likely part.
• Repair it when the fix is a single, accessible component such as a lid switch or pump.
• Replace it when you have multiple major failures (leaks plus no spin plus loud grinding) or repeated breakdowns.
• Replace it when the tub, basket, or gear case area is damaged and the repair becomes a large teardown.
• Confirm safe DIY steps and operating checks in the owner's manual.

These are frequent, straightforward fixes for Kenmore top-load designs:

• Won’t drain or leaves water behind: washer drain pump WP3363394
• Won’t start or stops when the lid is opened/closed: washer lid switch assembly WP8318084
• Agitator moves poorly or “ratchets”: agitator dog 80040
• Motor runs but washer won’t agitate/spin: washer motor coupling 285753A

A targeted repair keeps a dependable Kenmore washer running for years and avoids the cost and hassle of replacement. The key is diagnosing the symptom correctly so you replace the right part the first time.

Last updated: February 2026

Your Kenmore Elite washer model is 11016942503. On this washer, the model number is printed on a rating label that’s typically on the back of the control panel, on the cabinet near the bottom, or under the lid area; confirm the exact location using the owner's manual.

Check these common spots on Kenmore top-load washers like model 11016942503:

• Back of the control panel (often easiest to see with a flashlight)
• Along the top rim under the lid (lift the lid and look around the opening)
• On the main cabinet near the bottom edge (front or side)
• Rear panel near the bottom (especially if the washer has been moved)

The label usually includes both a model number and a serial number.

• Model number identifies the exact washer design (used to match parts like a lid switch or drain pump).
• Serial number identifies your specific unit (useful for age and production details).

Using the exact model number 11016942503 prevents ordering the wrong replacement part and helps match the correct repair instructions. For example, common repairs on this platform involve items like the washer lid switch assembly WP8318084 or the washer drain pump WP3363394.

• Wipe the area with a damp cloth to remove detergent residue
• Use your phone camera zoom and a bright light
• If the washer was recently installed or moved, review the label and setup steps in the installation guide

Last updated: February 2026

The Kenmore Elite 11016942503 does not use a dedicated “reset” button like some electronics; most resets are done by stopping the cycle and restarting it using the Cycle Control knob, or by resetting a specific control (such as the water level control) as described in the owner's manual.

Use this when the washer seems paused, stuck, or you want to restart the cycle.

• Push in the Cycle Control knob to stop the washer.
• Wait about 2 minutes if the washer is in a normal pause during certain cycles.
• Make sure the lid is closed (it will not agitate or spin with the lid open).
• Pull out the Cycle Control knob to restart.
• If the washer is overloaded, reduce the load size and restart.

Your washer can have a Variable Water Level control that includes a reset position.

• Turn the WATER LEVEL selector to RESET.
• Then turn it to the desired water level setting.

This is a control reset for the water level selection, not a full machine reset.

These are the most common causes we see on Kenmore top-load washers like model 11016942503.

• Check the home electrical supply; reset the breaker or replace a blown fuse.
• Confirm the washer is not in a programmed pause.
• Verify the lid is fully closed; a failed lid switch can prevent spin/agitation.
• Make sure the drain hose is installed correctly (not sealed into the standpipe).
• Avoid very cold wash water (below about 60°F); detergent may not dissolve well and cycles can perform poorly.

Using the correct stop and restart method protects the timer and drive system, and it helps you avoid misdiagnosing a normal cycle pause as a failure.

Last updated: February 2026